Vq35hr 20psi stillen blower

Pro4Jackster · 04-13-2014, 12:36 PM

What up man? I come and go on the forums. Usually just read. Sell me your kit when you decide to go LS.

O&G · 04-13-2014, 12:52 PM

Quote:

Originally Posted by Pro4Jackster

What up man? I come and go on the forums. Usually just read. Sell me your kit when you decide to go LS.

LOL, I would never set a non Nissan motor in my baby! We need to get the rest of those break in miles in on the car, I know your a busy guy though! Tran drives her when he can!

YzGyz · 04-13-2014, 02:25 PM

My name is Tran. I can drive her for you. B ^ D

1slow370 · 04-13-2014, 05:24 PM

http://www.vortechsuperchargers.com/pdf/si_cmap.pdfMore cooling will help, the vortechs pump a lot of heat once you spin them faster. This is the old SI map and you are getting into the 65% efficiency island.

O&G · 04-13-2014, 09:19 PM

Quote:

Originally Posted by Pro4Jackster

I just saw this. It is my car. I got the cog pulley idea from the Stillen supercharged guys on this forum. I am running the 3.2" serp pulley that comes with the kit. The rear pulleys were a 1:1 ratio and were changed out for 34T:30T setup and JTran made the idler pulley and got everything to work. Should be spinning the Si impeller around 56K rpms. It made 13+ psi on the SCi impeller at the same rpms, so I think 16+ psi is probable with the Si. Also have a 28T pulley in Ron's toolbox, but we haven't been able to make it work without shredding cog belts. It would spin the blower around 61K rpms, but I don't think it's going to happen. That setup will surely push close to 20 psi, but I'm not in a rush to make that work right now. For extra cooling, we added meth injection.

The car made 266hp w/ boltons and tune. 409hp w/ Stillen SC. 420+hp w/cogs. 450+hp when it blew w/ cogs and Si impeller and quite a bit of belt slip(15 psi @ 6500 rpms and held 15psi to redline).

We'll see how it does in a couple of weeks. I ran a 12.5 @ 114 on street tires with the cog pulleys and SCi impeller. I am a Novice.

All facts. Take them or leave them.

Also remember JTrans dyno reads lower than even other Mustang dynos, it's a relic, which is why he is switching to a new setup soon. We will all have a dyno jet day so we can compare numbers with all these other cats throwing out "big numbers", but as far as a tuning tool, it still does the job well!

1slow370 · 05-11-2014, 03:38 AM

Final Results?

Pro4Jackster · 05-11-2014, 06:37 PM

Still breaking it in. I should have some final results by the end of the month.

O&G · 05-11-2014, 07:18 PM

^hard worker, always on the road.... and I don't think the Z will make it out to some of those rig sites! Business is good down in the great state of Texas!

Pro4Jackster · 05-22-2014, 09:00 AM

I have given up on the Stillen Supercharger. It got to the point where we were going to have to redesign most of the original kit to make anymore power (belt routing, charge pipe, relocate MAFs, new air filter and intake pipe, bigger heat exchanger, separate IAT sensor, etc). And since we are already spinning the SI in the red at 56K rpms, I don't want to spend any more money on this setup. I just sold the kit to a local guy and it's getting installed right now.

My motor was finished a couple of months ago, and now has just over 1000 miles on it. We ended up going with 10:1 Arias pistons and Carrillo rods. Ron took apart and cleaned the heads up. So the motor is ready for a lot more than this kit can put out. So it's time for a JTran Motorsports Low-Mount Single Turbo.

jwick · 05-22-2014, 09:11 AM

Quote:

Originally Posted by Pro4Jackster

I have given up on the Stillen Supercharger. It got to the point where we were going to have to redesign most of the original kit to make anymore power (belt routing, charge pipe, relocate MAFs, new air filter and intake pipe, bigger heat exchanger, separate IAT sensor, etc). And since we are already spinning the SI in the red at 56K rpms, I don't want to spend any more money on this setup. I just sold the kit to a local guy and it's getting installed right now.

My motor was finished a couple of months ago, and now has just over 1000 miles on it. We ended up going with 10:1 Arias pistons and Carrillo rods. Ron took apart and cleaned the heads up. So the motor is ready for a lot more than this kit can put out. So it's time for a JTran Motorsports Low-Mount Single Turbo.

Nice decision. What turbo you selecting? I'm running the BP PT6266 Twin Scroll. Same size as JTran put in that last Nismo he built but with a divided housing.

Pro4Jackster · 05-22-2014, 09:40 AM

I don't know yet. Johnny and Ron are still talking about it. They are going to pick the turbo. They are slightly more qualified than me to make those decisions. Ha.

jwick · 05-22-2014, 09:51 AM

Quote:

Originally Posted by Pro4Jackster

I don't know yet. Johnny and Ron are still talking about it. They are going to pick the turbo. They are slightly more qualified than me to make those decisions. Ha.

You are in good hands with those two. Can't wait to see progress. I'll be in and out a few weekends in June getting some things adjusted on the G.

elperuano · 05-22-2014, 09:57 AM

That makes 3 people now! Congrats! Now you're ready for serious power!

1slow370 · 05-22-2014, 11:32 AM

Quote:

Originally Posted by Pro4Jackster

I have given up on the Stillen Supercharger. It got to the point where we were going to have to redesign most of the original kit to make anymore power (belt routing, charge pipe, relocate MAFs, new air filter and intake pipe, bigger heat exchanger, separate IAT sensor, etc). And since we are already spinning the SI in the red at 56K rpms, I don't want to spend any more money on this setup. I just sold the kit to a local guy and it's getting installed right now.

My motor was finished a couple of months ago, and now has just over 1000 miles on it. We ended up going with 10:1 Arias pistons and Carrillo rods. Ron took apart and cleaned the heads up. So the motor is ready for a lot more than this kit can put out. So it's time for a JTran Motorsports Low-Mount Single Turbo.

ladies and gentleman of the jury... I CALLED THAT ****!

O&G · 05-22-2014, 11:57 AM

I like to sit on forums all day and stroke my epenis!

sent from my Note 3

04-13-2014, 12:36 PM	#61 (permalink)
Pro4Jackster Base Member Join Date: Oct 2011 Location: NW Houston Posts: 130 Drives: '08 350Z Rep Power: 14	What up man? I come and go on the forums. Usually just read. Sell me your kit when you decide to go LS. O&G likes this. __________________ Jtranbuilt '08 Z [Jtran PT7075 Single - Fujitsubo - Transgo - Wilwood - TE37SL - BC Racing]

04-13-2014, 05:24 PM	#64 (permalink)
1slow370 A True Z Fanatic Join Date: Aug 2009 Location: In the D Posts: 3,732 Drives: v8 74 260z ;) Rep Power: 7251	http://www.vortechsuperchargers.com/pdf/si_cmap.pdfMore cooling will help, the vortechs pump a lot of heat once you spin them faster. This is the old SI map and you are getting into the 65% efficiency island. __________________ ANSWER PRICE LIST Answers - - - - - - - - - - - - - - - - $0.75 Answers (requiring thought) - - - - $1.25 Answers (correct) - - - - - - - - - - $12.50

05-11-2014, 03:38 AM	#66 (permalink)
1slow370 A True Z Fanatic Join Date: Aug 2009 Location: In the D Posts: 3,732 Drives: v8 74 260z ;) Rep Power: 7251	Final Results? DEpointfive0 likes this. __________________ ANSWER PRICE LIST Answers - - - - - - - - - - - - - - - - $0.75 Answers (requiring thought) - - - - $1.25 Answers (correct) - - - - - - - - - - $12.50

05-11-2014, 06:37 PM	#67 (permalink)
Pro4Jackster Base Member Join Date: Oct 2011 Location: NW Houston Posts: 130 Drives: '08 350Z Rep Power: 14	Still breaking it in. I should have some final results by the end of the month. DEpointfive0 likes this. __________________ Jtranbuilt '08 Z [Jtran PT7075 Single - Fujitsubo - Transgo - Wilwood - TE37SL - BC Racing]

05-11-2014, 07:18 PM	#68 (permalink)
O&G A True Z Fanatic Join Date: Nov 2010 Location: Lone Star State Age: 42 Posts: 1,212 Drives: 40th Anv. Rep Power: 23	^hard worker, always on the road.... and I don't think the Z will make it out to some of those rig sites! Business is good down in the great state of Texas! __________________ O&G's Build/Journal <---(1st lowmount single turbo treeseventy) Built Engine Thread 2011 F-250 Build/Journal

04-13-2014, 02:25 PM	#63 (permalink)
YzGyz A True Z Fanatic Join Date: Jun 2013 Location: Houston Posts: 1,449 Drives: 2010 Nismo Rep Power: 64	My name is Tran. I can drive her for you. B ^ D

05-22-2014, 09:00 AM	#69 (permalink)
Pro4Jackster Base Member Join Date: Oct 2011 Location: NW Houston Posts: 130 Drives: '08 350Z Rep Power: 14	I have given up on the Stillen Supercharger. It got to the point where we were going to have to redesign most of the original kit to make anymore power (belt routing, charge pipe, relocate MAFs, new air filter and intake pipe, bigger heat exchanger, separate IAT sensor, etc). And since we are already spinning the SI in the red at 56K rpms, I don't want to spend any more money on this setup. I just sold the kit to a local guy and it's getting installed right now. My motor was finished a couple of months ago, and now has just over 1000 miles on it. We ended up going with 10:1 Arias pistons and Carrillo rods. Ron took apart and cleaned the heads up. So the motor is ready for a lot more than this kit can put out. So it's time for a JTran Motorsports Low-Mount Single Turbo. Mr.Squeeze, jwick and elperuano like this. __________________ Jtranbuilt '08 Z [Jtran PT7075 Single - Fujitsubo - Transgo - Wilwood - TE37SL - BC Racing]

05-22-2014, 09:40 AM	#71 (permalink)
Pro4Jackster Base Member Join Date: Oct 2011 Location: NW Houston Posts: 130 Drives: '08 350Z Rep Power: 14	I don't know yet. Johnny and Ron are still talking about it. They are going to pick the turbo. They are slightly more qualified than me to make those decisions. Ha. __________________ Jtranbuilt '08 Z [Jtran PT7075 Single - Fujitsubo - Transgo - Wilwood - TE37SL - BC Racing]

05-22-2014, 09:57 AM	#73 (permalink)
elperuano A True Z Fanatic Join Date: Oct 2011 Location: Southwest FL Posts: 1,374 Drives: G37S Rep Power: 29	That makes 3 people now! Congrats! Now you're ready for serious power! Pro4Jackster likes this.

05-22-2014, 11:57 AM	#75 (permalink)
O&G A True Z Fanatic Join Date: Nov 2010 Location: Lone Star State Age: 42 Posts: 1,212 Drives: 40th Anv. Rep Power: 23	I like to sit on forums all day and stroke my epenis! sent from my Note 3 __________________ O&G's Build/Journal <---(1st lowmount single turbo treeseventy) Built Engine Thread 2011 F-250 Build/Journal

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
My Stillen blower blew up :(	FireDan50	Forced Induction	20	08-22-2013 06:05 AM
GReddy High Capacity Aluminum Oil Pan VQ35HR VQ37HR USED $269 w/ FREE SHIPPING*	Sales@AAMComp	Drivetrain/Engine	12	10-30-2012 12:53 PM
WTB: ATI Blower Fan	DIGItonium	Misc Items for sale (No Z stuff)	6	12-29-2010 01:38 PM
Any 370s running higher than 20psi?	GoDZiLLa_845	Forced Induction	68	04-16-2010 11:31 PM
NEW Exedy Stage 2 Cerametalic Clutch Kit w/Chromaly Flywheel VQ35HR/VQ37	NIZMOZ	Parts for sale (Private Classifieds)	8	10-25-2009 08:49 AM