Boosted Performance single turbo build

Nixlimited · 05-03-2012, 12:19 AM

@Boosted: Did you consider a SS turbine housing for weight savings and corrosion prevention considering the placement of the turbo?

O&G · 05-03-2012, 12:51 PM

Quote:

Originally Posted by Nixlimited

@Boosted: Did you consider a SS turbine housing for weight savings and corrosion prevention considering the placement of the turbo?

why does the placement matter for this? It wouldn't be the same if the turbo was anywhere else? I'm sure the customer can choose those options if they want to spend the extra coin. My turbo turbines are ceramic coated but I havn't seen any turbos around here suffering from corrosion and we have tons of humidity and salt air.

Bet boosted has this thing at the dyno already LOL!

Nixlimited · 05-03-2012, 02:24 PM

Quote:

Originally Posted by O&G

why does the placement matter for this? It wouldn't be the same if the turbo was anywhere else? I'm sure the customer can choose those options if they want to spend the extra coin. My turbo turbines are ceramic coated but I havn't seen any turbos around here suffering from corrosion and we have tons of humidity and salt air.

Bet boosted has this thing at the dyno already LOL!

Well, turbos on many OEM applications are protected by splash plates. I am not worried about the turbo rusting away or anything, merely a curiosity. Plus, the SS hotsides are much lighter, which is nice, particularly where you have pipes supporting part of the turbo's weight. Anyway, based on BP's response, looks like it's not even an option here.

Quote:

Originally Posted by Boosted Performance

Well, for starters there is no such thing as a SS divided turbine housing...remember, this is a twin scroll turbo system. On top of that, I use Precision turbos and Precision does not offer this as an option, only Garrett turbo does. They also only offer it for the GT35R turbo and the GT42 (a rather large turbo). The heat alone will prevent the housing from rusting, it may develope a bit of surface corrosion but that is as far as it will go.

I think there are Tial Sport SS hotsides available for a broader range of Garrett turbos: link

Quote:

Originally Posted by GaleForce

What is the benefit of running open dump for the waste gates?

Quote:

Originally Posted by Dzel

I would like to know this as well?

In theory, even less exhaust back-pressure since the exhaust that bypasses the turbo gets vented to atmosphere rather than back into the exhaust system. However, I have to believe that for most street applications, the performance difference is nominal.

05-03-2012, 12:19 AM	#1 (permalink)
Nixlimited A True Z Fanatic Join Date: Aug 2009 Location: San Diego Posts: 1,235 Drives: 15 GT-R / 11 Prius Rep Power: 28	@Boosted: Did you consider a SS turbine housing for weight savings and corrosion prevention considering the placement of the turbo? __________________ Car Sold! Pleasure being a part of the Z community. New ride: 2015 GT-R - 647 WHP / 641 WTQ (e85) & 543 WHP / 519 WTQ (91)

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Twin Turbo vs. Single Turbo V6: A Dissertation	Mike@GTM	Forced Induction	115	08-14-2014 10:04 PM
STS 370Z Single Turbo System	STSTurbo.com	Forced Induction	337	11-21-2012 11:55 AM
Question about a single turbo set up?	dnasty370z	Forced Induction	8	07-26-2012 11:56 AM
New Single Turbo Option.. yes please	Isamu	Forced Induction	108	05-09-2012 09:07 AM
Will we see a SINGLE turbo kit?	Brazilbro	Forced Induction	17	07-03-2009 05:03 PM