Stillen SC ?

14Q60awdSPORT · 03-07-2022, 05:34 PM

Quote:

Originally Posted by Averying

The reason that the Stillen kit has been labeled as unreliable is not because of the power that it produces, but rather the design itself being flawed. This thread (Before Installing Stillen Supercharger) goes over the issues. Basically MAF before intercooler = bad.

I’m sure the unreliability is hyped up a bit since people are less likely to report good results than to bash it if they have a problem. But Bottom line.. there are better options.

Sent from my iPhone using Tapatalk

Most people trash the kit because it does not make a lot of power and requires a lot of modifications to the kit like A2A conversion to make some real power. And if your goal was power I’d recommend the topgunz rotrex kit (which I have myself)

The MAF location is a concern but on the carb tune it is accounted for in the tune and the boost levels and subsequent heat are much lower so the concern in this case is minimal.

Op is looking for a conservative safe setup to presumably add just a little over FBO NA levels and not push it. The stillen carb seems to fit the bill, at about 370-400whp. Most people want and expect more. It’s easy to get greedy or have unrealistic expectations and then the stillen falls short requiring you to spend a lot to fix it it to make closure to 500whp+ like most people really want to satisfy.

He didn’t mention budget or his DIY capabilities, but IAT relocation isn’t that hard, adding WMI isn’t difficult and would bring IAT down much closer to pre blower temps IAT was reading if he didn’t relocate. but on carb setup I don’t think it’s a huge deal.

redondoaveb · 03-07-2022, 06:54 PM

Quote:

Originally Posted by 14Q60awdSPORT

Most people trash the kit because it does not make a lot of power and requires a lot of modifications to the kit like A2A conversion to make some real power. And if your goal was power I’d recommend the topgunz rotrex kit (which I have myself)

The MAF location is a concern but on the carb tune it is accounted for in the tune and the boost levels and subsequent heat are much lower so the concern in this case is minimal.

Op is looking for a conservative safe setup to presumably add just a little over FBO NA levels and not push it. The stillen carb seems to fit the bill, at about 370-400whp. Most people want and expect more. It’s easy to get greedy or have unrealistic expectations and then the stillen falls short requiring you to spend a lot to fix it it to make closure to 500whp+ like most people really want to satisfy.

He didn’t mention budget or his DIY capabilities, but IAT relocation isn’t that hard, adding WMI isn’t difficult and would bring IAT down much closer to pre blower temps IAT was reading if he didn’t relocate. but on carb setup I don’t think it’s a huge deal.

But boost is addicting and that 370-400whp is going to feel slow real quick and he'll want to upgrade. Ask me how I know, or just look at my signature

14Q60awdSPORT · 03-07-2022, 07:01 PM

Quote:

Originally Posted by redondoaveb

But boost is addicting and that 370-400whp is going to feel slow real quick and he'll want to upgrade. Ask me how I know, or just look at my signature

That I agree with. The temptation is hard to overcome especially when its so close.

Nice sig. didn’t notice at first.

I got a topgunz rotrex sc at 11psi by 4500rpm flatlined to redline on E40, cjm return, Id1300, walbro 535, KB boost a pump, isr longtube header etc…. Guessing a solid 500AWHP. 1-2 pulls super hard. 3rd is fun, 4th is already boring lol.

redondoaveb · 03-07-2022, 07:21 PM

Quote:

Originally Posted by 14Q60awdSPORT

That I agree with. The temptation is hard to overcome especially when its so close.

Nice sig. didn’t notice at first.

I got a topgunz rotrex sc at 11psi by 4500rpm flatlined to redline on E40, cjm return, Id1300, walbro 535, KB boost a pump, isr longtube header etc…. Guessing a solid 500AWHP. 1-2 pulls super hard. 3rd is fun, 4th is already boring lol.

Good thing about his kit is you can dial up the boost when you want more power. You have a lot of boost left

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[FOR SALE] Stillen Dual Exhaust & Stillen front plate holder Pick up in Bay Area	A7594217	Parts for sale (Private Classifieds)	17	08-04-2013 11:27 PM
STILLEN Stillen Gen 3 Ultra Long Tube Dual Intake Kit Nissan 370Z	alright	Forced Induction	4	03-20-2013 02:38 PM
[WTB] wtb nismo seats stillen g3 cai stillen headers and stillen exhaust	bloodvayne	Parts for sale (Private Classifieds)	1	12-18-2011 09:25 PM
FI 12" Exhaust - Stillen G3 Intakes - Stillen UD Pulley - GAINED 28kw or 37HP	bezzita	Australia/New Zealand	29	09-27-2009 12:53 PM
FI 12" Exhaust - Stillen G3 Intakes - Stillen UD Pulley - GAINED 28kw or 37HP	bezzita	Engine & Drivetrain	6	09-06-2009 05:20 PM