Using Jack Stand...where to contact point?

supraman626 · 11-11-2011, 07:57 PM

Zmyride, i have rhino ramps too and i use some thick wooden boards such as 4x4s or whatever you call it to get up the ramp and it doesn't really scratch. i seen a black 370z from time to time, wonder if that was you. i'm in the sunset area.

CB1 · 11-11-2011, 08:41 PM

Is it the large center dimple that protrudes downward in that silver cross brace just behind the black plastic cover?

CB1 · 11-11-2011, 08:45 PM

I am putting on HFC and a CBE system. Got everything off except the stock cats. Damm those bolts are a mother f*cker!!!!! I already broke a 14mm socket trying to get the passenger side bolt loose that you have to go in from the top of the engine bay. St*t!

CB1 · 11-11-2011, 09:08 PM

Nissan 370Z Forum - CB1's Album: Misc. - Picture

Hard to see my red circles... Are these the front and rear "Garage Jack Points"?

dAvenue · 11-11-2011, 09:21 PM

Quote:

Originally Posted by CB1

Nissan 370Z Forum - CB1's Album: Misc. - Picture

Hard to see my red circles... Are these the front and rear "Garage Jack Points"?

For the front, that is the contact point I used. I haven't needed to jack up the rear yet, though.

WShade · 11-11-2011, 09:58 PM

Quote:

Originally Posted by CB1

Nissan 370Z Forum - CB1's Album: Misc. - Picture

Hard to see my red circles... Are these the front and rear "Garage Jack Points"?

Figured I would post in this thread and not the other. That is it. I have a Craftsman 4 ton jack with removable saddle. I remove the saddle when I jack the front and the dimple fits right in the hole on the jack plate very nice and secure.

slam1918 · 05-27-2012, 11:03 AM

Its easy to drive on the Ryno ramps without removing the front air dam. just cut a piece of 1/2" plywood 9" wide about 2 to 3' long. Stick a 2x4 block under the ply and set them a short way up the ramp. Bada Bing, drive right up your ryno's.

11-11-2011, 08:41 PM	#2 (permalink)
CB1 Base Member Join Date: Jun 2011 Location: Washington Posts: 192 Drives: 2011 Touring/Sport Rep Power: 31	Is it the large center dimple that protrudes downward in that silver cross brace just behind the black plastic cover? __________________ 2011 Metallic Black, Touring/Sport, Nav, AT \| F.I. Twin Turbo #060 \| E85 \| F.I. Built 7AT \| F.I. Flex Plate \| F.I. 34 Row Oil Cooler \| F.I. 19 Row 7AT Cooler \| ECUTEK Tuned By Sebastian \| 647 WHP 605 TQ \|

11-11-2011, 08:45 PM	#3 (permalink)
CB1 Base Member Join Date: Jun 2011 Location: Washington Posts: 192 Drives: 2011 Touring/Sport Rep Power: 31	I am putting on HFC and a CBE system. Got everything off except the stock cats. Damm those bolts are a mother fcker!!!!! I already broke a 14mm socket trying to get the passenger side bolt loose that you have to go in from the top of the engine bay. Stt! __________________ 2011 Metallic Black, Touring/Sport, Nav, AT \| F.I. Twin Turbo #060 \| E85 \| F.I. Built 7AT \| F.I. Flex Plate \| F.I. 34 Row Oil Cooler \| F.I. 19 Row 7AT Cooler \| ECUTEK Tuned By Sebastian \| 647 WHP 605 TQ \|

11-11-2011, 09:08 PM	#4 (permalink)
CB1 Base Member Join Date: Jun 2011 Location: Washington Posts: 192 Drives: 2011 Touring/Sport Rep Power: 31	Nissan 370Z Forum - CB1's Album: Misc. - Picture Hard to see my red circles... Are these the front and rear "Garage Jack Points"? __________________ 2011 Metallic Black, Touring/Sport, Nav, AT \| F.I. Twin Turbo #060 \| E85 \| F.I. Built 7AT \| F.I. Flex Plate \| F.I. 34 Row Oil Cooler \| F.I. 19 Row 7AT Cooler \| ECUTEK Tuned By Sebastian \| 647 WHP 605 TQ \|

05-27-2012, 11:03 AM	#7 (permalink)
slam1918 Base Member Join Date: Feb 2012 Location: Tequesta, Fl Posts: 60 Drives: 10 370Z White A/T Rep Power: 15	Ryno ramps Its easy to drive on the Ryno ramps without removing the front air dam. just cut a piece of 1/2" plywood 9" wide about 2 to 3' long. Stick a 2x4 block under the ply and set them a short way up the ramp. Bada Bing, drive right up your ryno's.

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

11-11-2011, 07:57 PM	#1 (permalink)
supraman626 Base Member Join Date: Feb 2009 Location: sf, ca Posts: 58 Drives: 09 Nissan 370z PW M6 Rep Power: 18	Zmyride, i have rhino ramps too and i use some thick wooden boards such as 4x4s or whatever you call it to get up the ramp and it doesn't really scratch. i seen a black 370z from time to time, wonder if that was you. i'm in the sunset area.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Jack Stand Question	spearfish25	Nissan 370Z General Discussions	143	10-16-2015 11:30 AM
Rear jack point	speedworks	Intake/Exhaust	20	10-27-2010 09:36 AM
Jack Stands	Minicobra1	DIY Section (Do-It-Yourself)	19	03-07-2010 04:54 PM
Stand behind your car and push down on the hatch.	shesha	Nissan 370Z General Discussions	18	09-14-2009 03:57 AM
Dealership contact/updates after ordering a car	takimbe	Nissan 370Z Pricing / Ordering Discussions	13	04-03-2009 01:42 AM