STILLEN 370Z Urethane Fascia - Sneak Peek - In Development

370zproject · 03-21-2010, 01:21 PM

Quote:

Originally Posted by AK370Z

Our photoshop expert ERIC did one in the other Stillen thread

Urgent help needed!!!

only thing i would be worried about is the big gap allowing water to get into the engine bay... kinda a newbie at this and my z is my dd ... like the gen 3 intakes do those protect aginst water intake?

Trips · 03-21-2010, 01:30 PM

Quote:

Originally Posted by 370zproject

only thing i would be worried about is the big gap allowing water to get into the engine bay... kinda a newbie at this and my z is my dd ... like the gen 3 intakes do those protect aginst water intake?

water isn't going to be to much of an issues since they sit at the highest level possible

370zproject · 03-21-2010, 01:40 PM

hmm it happened to my bros rsx.. water got in.. blew his block up

AK370Z · 03-21-2010, 01:51 PM

Quote:

Originally Posted by 370zproject

hmm it happened to my bros rsx.. water got in.. blew his block up

Your brother probably had the cold air intake like AEM or whatever on his RSX. I had my friends RSX hydrolocked too. That's because those cold air intakes filter stays very very low to the ground. I believe it stays in front of the front wheel. I wouldn't worry about Stillen G3 on the 370Z since it sits up waaay high up. Take a look:

Lets keep this thread on topic. If you have questions about G3 intakes, take a look at this thread here http://www.the370z.com/diy-section-d...3-intakes.html . Thanks

LateralG'z · 03-21-2010, 05:41 PM

Does this front have holes that guide air to the G3 intakes, that would be really and allow for better air to them? BTW this is a great front end.

Quote:

Originally Posted by 370zproject

only thing i would be worried about is the big gap allowing water to get into the engine bay... kinda a newbie at this and my z is my dd ... like the gen 3 intakes do those protect aginst water intake?

RCZ · 03-21-2010, 09:11 PM

^ Yup, there is an opening between the bumper beam cover and the top edge of the front of the bumper.

LateralG'z · 03-21-2010, 11:52 PM

Thank you.

+1

Quote:

Originally Posted by RCZ

^ Yup, there is an opening between the bumper beam cover and the top edge of the front of the bumper.

Red370 · 03-21-2010, 11:54 PM

Quote:

Originally Posted by LateralG'z

Thank you.

+1

just get em, you know you wanna.

LateralG'z · 03-21-2010, 11:56 PM

When is this available to purchase?

Quote:

Originally Posted by Kyle@STILLEN

Judging by how many phone calls and emails we get on a daily basis from people who can't wait to purchase this fascia...I would say that this fascia has quite a lot of appeal.

But thank you for your input. Once the complete kit is finished perhaps your opinion will change.

370zproject · 03-22-2010, 06:32 AM

is there a finished product?

htt760 · 03-22-2010, 01:00 PM

Quote:

Originally Posted by 370zproject

is there a finished product?

we are still awaiting stillen to finish a few things on mounting and install information before officially shipping out the products. they want to make sure everything is legit.

Red370 · 03-22-2010, 01:02 PM

man, i think this thing would look good with a carbon fiber overlay on the lip.

Kyle@STILLEN · 03-22-2010, 01:06 PM

We're finalizing a few things right now. During our testing of the fascia we found that the top mounting surface was a little thin and a little weak. We used the factory fascia for this section and it might have been a bit too thin. So, the craftsmen in the modeling shop worked on that on Friday and again this morning. We should know more this afternoon. I was hoping to have everyone wrapped up and shipped on Friday but as everyone has said, we would all rather wait until everything is perfect before we ship them out.

We're a few pages deep now so I though it would be a good time to recap some of the integrated features of the fascia.

1) Additional cooling- We opened up the main center opening to allow for a lot more air flow.

2) Even more airflow- We plan on offering an additional oil cooler which can be mounted behind the vent on the driver's side. For the guys who purchased the street cooler first, then the motorsport cooler...That street cooler fits perfectly in the side opening so you can now run both. This is what we plan on doing for our car.

3) Still more airflow- We have incorporated a small vent underneath the top section of the fascia. This small vent will help direct air to the Gen. 3's, supercharger intakes, and intercooler.

4) Brake ducts- We will be building some modular brake ducts for people who want to either keep the fang look or for the guy who just wants brake ducting. Either way, these will be 100% functional and work perfectly for both people.

5) Great looks- We wanted to keep this looking good but functionality was definitely the primary focus.

Mike · 03-22-2010, 04:19 PM

No worries Kyle! Its worth waiting a few more days.

370zproject · 03-22-2010, 04:41 PM

Quote:

Originally Posted by Kyle@STILLEN

We're finalizing a few things right now. During our testing of the fascia we found that the top mounting surface was a little thin and a little weak. We used the factory fascia for this section and it might have been a bit too thin. So, the craftsmen in the modeling shop worked on that on Friday and again this morning. We should know more this afternoon. I was hoping to have everyone wrapped up and shipped on Friday but as everyone has said, we would all rather wait until everything is perfect before we ship them out.

We're a few pages deep now so I though it would be a good time to recap some of the integrated features of the fascia.

1) Additional cooling- We opened up the main center opening to allow for a lot more air flow.

2) Even more airflow- We plan on offering an additional oil cooler which can be mounted behind the vent on the driver's side. For the guys who purchased the street cooler first, then the motorsport cooler...That street cooler fits perfectly in the side opening so you can now run both. This is what we plan on doing for our car.

3) Still more airflow- We have incorporated a small vent underneath the top section of the fascia. This small vent will help direct air to the Gen. 3's, supercharger intakes, and intercooler.

4) Brake ducts- We will be building some modular brake ducts for people who want to either keep the fang look or for the guy who just wants brake ducting. Either way, these will be 100% functional and work perfectly for both people.

5) Great looks- We wanted to keep this looking good but functionality was definitely the primary focus.

post pics when done

03-21-2010, 01:40 PM	#183 (permalink)
370zproject A True Z Fanatic Join Date: Jul 2009 Location: Memphis Age: 34 Posts: 16,104 Drives: 09 A/T 370z blue Rep Power: 52	hmm it happened to my bros rsx.. water got in.. blew his block up __________________ Brake Upgrade Package ate blue, hawk hp ceramic pads, and slotted rotors

03-22-2010, 06:32 AM	#190 (permalink)
370zproject A True Z Fanatic Join Date: Jul 2009 Location: Memphis Age: 34 Posts: 16,104 Drives: 09 A/T 370z blue Rep Power: 52	is there a finished product? __________________ Brake Upgrade Package ate blue, hawk hp ceramic pads, and slotted rotors

03-22-2010, 01:02 PM	#192 (permalink)
Red370 A True Z Fanatic Join Date: Jul 2009 Location: Kaiserslautern, Germany Posts: 4,391 Drives: your mom to church Rep Power: 295	man, i think this thing would look good with a carbon fiber overlay on the lip. __________________ 2011 Mustang 5.0 \| 3.55's \| Lethal Performance off road H-Pipe \| Magnaflow Muffler Delete \| JLT CAI/Bama tuned 417whp/ 404 ft/lbs

03-22-2010, 04:19 PM	#194 (permalink)
Mike The370Z.com Sponsor Join Date: Jun 2009 Location: Loganville, GA Posts: 5,944 Drives: 370z Rep Power: 2185	No worries Kyle! Its worth waiting a few more days. __________________ NISSAN: 75 280Z / 86 300ZX GLL /87 Sentra SE / 03 350Z / 23 Z Porsche: 93 968 / 23 Macan GTS / 93 968

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Carbon Fiber front fascia?	kannibul	Exterior & Interior	21	09-30-2009 01:19 AM
front fascia cost?	Snakes709	Nissan 370Z General Discussions	7	09-22-2009 07:15 AM
Sneak Peek, Carbon Fiber B-Pillars @ The 370ZSOURCE!!!	Michael@TheZStore	Exterior & Interior	3	08-25-2009 05:21 PM
Sneak Peek, Carbon Fiber Door Sills @ The 370ZSOURCE!!!!!	Michael@TheZStore	Exterior & Interior	2	07-29-2009 03:58 PM
Going to sneak a peek at a 2010 Genesis Coupe in a few minutes!!!	iamtherhino	Other Vehicles	5	03-07-2009 10:08 AM

03-21-2010, 09:11 PM	#186 (permalink)
RCZ A True Z Fanatic Join Date: Nov 2008 Location: Miami Posts: 6,403 Drives: '09 370Z Rep Power: 1118	^ Yup, there is an opening between the bumper beam cover and the top edge of the front of the bumper.

03-22-2010, 01:06 PM	#193 (permalink)
Kyle@STILLEN The370Z.com Sponsor Join Date: Dec 2008 Location: Newport Beach Posts: 626 Drives: Toyota Tundra Rep Power: 306	We're finalizing a few things right now. During our testing of the fascia we found that the top mounting surface was a little thin and a little weak. We used the factory fascia for this section and it might have been a bit too thin. So, the craftsmen in the modeling shop worked on that on Friday and again this morning. We should know more this afternoon. I was hoping to have everyone wrapped up and shipped on Friday but as everyone has said, we would all rather wait until everything is perfect before we ship them out. We're a few pages deep now so I though it would be a good time to recap some of the integrated features of the fascia. 1) Additional cooling- We opened up the main center opening to allow for a lot more air flow. 2) Even more airflow- We plan on offering an additional oil cooler which can be mounted behind the vent on the driver's side. For the guys who purchased the street cooler first, then the motorsport cooler...That street cooler fits perfectly in the side opening so you can now run both. This is what we plan on doing for our car. 3) Still more airflow- We have incorporated a small vent underneath the top section of the fascia. This small vent will help direct air to the Gen. 3's, supercharger intakes, and intercooler. 4) Brake ducts- We will be building some modular brake ducts for people who want to either keep the fang look or for the guy who just wants brake ducting. Either way, these will be 100% functional and work perfectly for both people. 5) Great looks- We wanted to keep this looking good but functionality was definitely the primary focus.