Is it possible I'm scraping my Tranny?

TheGreatOne · 11-14-2011, 09:23 AM

Hey guys,

Just wondering if its possible that I could be scraping my shift linkage/tranny?

It happens whenever I leave my underground condo parking since I've been lowered on TEIN's

Its steep, so at the part where I even out, I scrape. Now at first I thought it was the little dust shields in front of the front wheels...but last few times I actually kept my hand on my shift knob...and I feel a vibration at the same time I scrape

I haven't had a chance to get on a lift yet to check for damage but I'm thinking I'm scraping my tranny casing? I imagine its pretty tough cast iron...but over time, this can't be good...

m4a1mustang · 11-14-2011, 09:26 AM

It's aluminum, not cast iron.

Your shift knob could be vibrating when you scrape for a number of reasons. IIRC there is pretty decent clearance for the transmission case so it would be a little difficult to hit right there, but you won't know for sure until you take a look under the car...

m4a1mustang · 11-14-2011, 09:29 AM

If you take a look at an underbody picture of the 370, it's unlikely you'd be hitting the transmission. There are a number of other bits that would scrape first.

modme · 11-14-2011, 09:34 AM

You should be scraping the transmission mount and brace. It's a black piece holding up the tranny. That piece should be able to take some abuse with no problems.

TheGreatOne · 11-14-2011, 09:51 AM

Thanks guys!

Thats comforting, although everytime it happens its cringe worthy lol. I'm still going to check it out as soon as i can..

poorazn · 11-14-2011, 10:27 AM

Quote:

Originally Posted by TheGreatOne

Thanks guys!

Thats comforting, although everytime it happens its cringe worthy lol. I'm still going to check it out as soon as i can..

All scraping is cringe worthy! I make my wife walk down to the next block when i pick her her from this shop who's entrance looks to steep for me to enter/leave :P

Punk86 · 11-14-2011, 12:15 PM

I have similar problems, but I guess its just apart of being low! My biggest problem is my exhaust scraps everywhere I go.

KillerBee370 · 11-14-2011, 03:52 PM

On a side note, I too scrape when I go too fast over a speed bump but for sure it's not the tranny but the cross brace that protects it (or the exhaust?). Anyway. No big deal... just take it slow!

vividracing · 11-14-2011, 06:52 PM

Since you scrape occasionally... You're ALMOST low enough

You're probably dragging the trans cross member, if anything. It's lower than the tranny and a few other things. Get under the car some time and look for scrapes.

UNKNOWN_370 · 11-14-2011, 07:26 PM

Quote:

Originally Posted by Punk86

I have similar problems, but I guess its just apart of being low! My biggest problem is my exhaust scraps everywhere I go.

This is why as bad as I want an FI exhaust I can't do it. I drive hard so putting on of those exhausts is a no go. I'm just going to get an hfc and y pipe. When I go turbo I'll get a turbo exhaust with it.

Punk86 · 11-15-2011, 10:47 AM

Quote:

Originally Posted by vividracing

Since you scrape occasionally... You're ALMOST low enough

I scrapped 5 times on the way to work... maybe I should slow it down a bit. But once my exhaust flanges wear down a lil bit I should be fine

KaienZ34 · 11-15-2011, 10:51 AM

I'm not lowered at all and i scrap everywhere, but it's just the black plastic things under the front bumper.

vividracing · 11-16-2011, 06:47 PM

Quote:

Originally Posted by Punk86

I scrapped 5 times on the way to work... maybe I should slow it down a bit. But once my exhaust flanges wear down a lil bit I should be fine

I approve!

And before any of the "function > form" crew chime in, my post about lowness was made in jest. Sort of. For a street car, I see no reason in having the optimal most hardcore track suspension. If you'd rather slam your car than maintain perfect suspension geometry, have at it! If you want to track your car, then don't slam it. Different strokes...

windex · 11-17-2011, 08:32 AM

Yea pretty sure its not you transmission scraping the ground. When my exhaust hit I sometimes feel it in the shifter. I dont think i've ever felt it vibrate when scrapping the chin though.

Quote:

Originally Posted by poorazn

All scraping is cringe worthy! I make my wife walk down to the next block when i pick her her from this shop who's entrance looks to steep for me to enter/leave :P

My girl waited for a parking spot on the first floor of her apartment complex just so she could move her car out of it when I came to visit. She heard me go over one speed bump and told me I never had to worry about parking past the first floor again.

Trips · 11-17-2011, 10:29 AM

Stay On Topic!!

11-14-2011, 09:23 AM	#1 (permalink)
TheGreatOne A True Z Fanatic Join Date: Jan 2011 Location: Montreal, Canada Age: 46 Posts: 1,980 Drives: E60 BMW M5 Rep Power: 21	Is it possible I'm scraping my Tranny? Hey guys, Just wondering if its possible that I could be scraping my shift linkage/tranny? It happens whenever I leave my underground condo parking since I've been lowered on TEIN's Its steep, so at the part where I even out, I scrape. Now at first I thought it was the little dust shields in front of the front wheels...but last few times I actually kept my hand on my shift knob...and I feel a vibration at the same time I scrape I haven't had a chance to get on a lift yet to check for damage but I'm thinking I'm scraping my tranny casing? I imagine its pretty tough cast iron...but over time, this can't be good... __________________ 2017 SUBARU STI 2008 E60 M5 - SOLD 2010 40th Anniversary 370Z - SOLD (and missing her)

11-14-2011, 09:26 AM	#2 (permalink)
m4a1mustang A True Z Fanatic Join Date: Feb 2009 Location: Northern VA Posts: 55,385 Drives: on two wheels Rep Power: 6962	It's aluminum, not cast iron. Your shift knob could be vibrating when you scrape for a number of reasons. IIRC there is pretty decent clearance for the transmission case so it would be a little difficult to hit right there, but you won't know for sure until you take a look under the car... __________________ - Steve Zs & Coffee - Saturdays at 10AM in Fairfax, VA and Columbia, MD (Click the banner!) LIKE us on Facebook!

11-14-2011, 09:29 AM	#3 (permalink)
m4a1mustang A True Z Fanatic Join Date: Feb 2009 Location: Northern VA Posts: 55,385 Drives: on two wheels Rep Power: 6962	If you take a look at an underbody picture of the 370, it's unlikely you'd be hitting the transmission. There are a number of other bits that would scrape first. __________________ - Steve Zs & Coffee - Saturdays at 10AM in Fairfax, VA and Columbia, MD (Click the banner!) LIKE us on Facebook!

11-14-2011, 09:34 AM	#4 (permalink)
modme Enthusiast Member Join Date: Mar 2009 Location: NY Posts: 345 Drives: G37 Rep Power: 16	You should be scraping the transmission mount and brace. It's a black piece holding up the tranny. That piece should be able to take some abuse with no problems. __________________ GTM Twin Turbo Stage 2\|GTR Turbo/Engine Gauges\|KW V3 Coilovers\|HKS Exhaust\|Oil Cooler\| Vossen CV1

11-14-2011, 09:51 AM	#5 (permalink)
TheGreatOne A True Z Fanatic Join Date: Jan 2011 Location: Montreal, Canada Age: 46 Posts: 1,980 Drives: E60 BMW M5 Rep Power: 21	Thanks guys! Thats comforting, although everytime it happens its cringe worthy lol. I'm still going to check it out as soon as i can.. __________________ 2017 SUBARU STI 2008 E60 M5 - SOLD 2010 40th Anniversary 370Z - SOLD (and missing her)

11-14-2011, 12:15 PM	#7 (permalink)
Punk86 Enthusiast Member Join Date: Aug 2010 Location: New Orleans, Louisiana Posts: 467 Drives: a neck breaker Rep Power: 14	I have similar problems, but I guess its just apart of being low! My biggest problem is my exhaust scraps everywhere I go. __________________ BC Racing Coilovers \|\| Stillen G3s \|\| Invidia CBE \|\| Work VS-XX \|\| Full Lip Kit Riding Low and Slow My Journal Thread!

11-14-2011, 03:52 PM	#8 (permalink)
KillerBee370 A True Z Fanatic Join Date: Mar 2009 Location: So Cal baby! Age: 51 Posts: 5,964 Drives: with passion Rep Power: 321	On a side note, I too scrape when I go too fast over a speed bump but for sure it's not the tranny but the cross brace that protects it (or the exhaust?). Anyway. No big deal... just take it slow!

11-14-2011, 06:52 PM	#9 (permalink)
vividracing The370Z.com Sponsor Join Date: Jun 2009 Location: Gilbert, AZ Age: 37 Posts: 7,306 Drives: 350Z,370Z,GTR Rep Power: 38	Since you scrape occasionally... You're ALMOST low enough You're probably dragging the trans cross member, if anything. It's lower than the tranny and a few other things. Get under the car some time and look for scrapes. __________________ Rocky @ Vivid ♦ 480.966.3040 x236 ♦ Rocky@vividracing.com Email, PM, or call me directly for aggressive The370Z.com member pricing!!!

11-15-2011, 10:51 AM	#12 (permalink)
KaienZ34 A True Z Fanatic Join Date: Oct 2009 Location: LA. not L.a. Posts: 21,652 Drives: Z34 Tour/Sport Rep Power: 177	I'm not lowered at all and i scrap everywhere, but it's just the black plastic things under the front bumper. __________________ *"These Violent Delights Have Violent Ends"* http://www.the370z.com/members/kaienz34-albums-z34.html

11-17-2011, 10:29 AM	#15 (permalink)
Trips Administrator Join Date: May 2009 Location: Disneyland, Ca Posts: 8,728 Drives: 🔰 Rep Power: 10	Stay On Topic!! __________________

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
front lip scraping	AdobePhil	Exterior & Interior	24	02-16-2012 02:42 PM
Scraping front spoiler on rolling curbs?	tjlazer	Nismo 370Z	5	04-03-2011 04:03 PM
Good luck scraping the ice off your car...	Xan	The Lounge (Off Topic)	11	01-31-2011 02:37 AM
what am i scraping?	darthanakin23	Nissan 370Z General Discussions	14	08-05-2010 05:10 PM
Maybe that scraping sound isnt the chin spoiler.	Dembflyr	Exterior & Interior	16	04-21-2010 08:34 PM