Nissan 370Z Forum  

P0340

Hi all, Just going to dump my problems here... Driving home the other day, everything seems fine until the freeway onramp when I lose all power. It feels like the

Go Back   Nissan 370Z Forum > Nissan 370Z Tech Area > Engine & Drivetrain


Like Tree28Likes

Reply
 
LinkBack Thread Tools Display Modes
Old 12-12-2019, 01:28 AM   #1 (permalink)
Base Member
 
Knio's Avatar
 
Join Date: May 2011
Location: Palo Alto, CA
Posts: 141
Drives: 40th
Rep Power: 13
Knio has a spectacular aura aboutKnio has a spectacular aura about
Default P0340

Hi all,

Just going to dump my problems here...

Driving home the other day, everything seems fine until the freeway onramp when I lose all power. It feels like the fuel starvation problem that I've experienced before, and I am low on fuel.. so I coast off the freeway, and eventually it gets some power back, but it's extremely jerky and definitely not a fuel starvation problem now.

I limp back to a parking lot. The idle is not smooth and bouncing between 800-1400, and it won't rev past 3.5k at all. When I tested revving it, TCS and slip lights also come on. I turn the engine off, try to turn it back on, it will crank but not fire.

Eventually I get a code reader working and see P0300 and P0340 - Camshaft position sensor error. Check the forums and see a few posts that mention unplugging the sensors might work. I clear the DTCs and try it:

Both sensors plugged in - won't start

Bank 2 unplugged - won't start

Bank 1 unplugged - will start, but cranks for much longer than normal, and is in limp mode and won't rev past 3.5k, but the idle is smooth, and everything feels fine otherwise! This has been reproducible every time.

I swapped the left and right sensors, both looked clean and the problem is still exactly the same, and not P0345, and still runs with only bank 2 plugged in, so I think both of the sensors themselves are working.

I probed all connections with a multimeter at both harnesses for OC, SC, and the signal, at the sensors themselves, and in the ECM harness and everything looks fine, and the left & right banks match, giving more evidence that it's not a sensor or electrical problem. I don't have a scope, but the signals are 5V when off and jump around near 4.5V when the engine is running, which is what you'd expect from working sensors.

I feel like I've eliminated any electrical problems, and could it really be a timing problem since the engine runs fine and smooth up to 3.5k in limp mode? But will keep looking.. I've ordered a scope to check the actual signals, and will try to remove the timing cover to inspect the camshaft gears and timing chain this weekend. Most of the other threads I saw didn't post resolutions. I'm hoping I can fix this myself and not have to take it to a dealer :P

Car is tuned with JWT intakes, Nismo exhaust, oil cooler, 60k miles.

Other threads:

Z throw P0340 and P0345 code after violent spun out on skidpad
Car won't start & pending Code P0340
2009 base won't start
Help me diagnose this problem: I can't rev past 3500 RPM intermittently (AK370Z)
Camshaft/Crankshaft Sensor, Limp Mode, Z issues :/
Need Help - Car Stalled and wont start
BettyZ likes this.
Knio is offline   Reply With Quote
Old 12-12-2019, 10:10 AM   #2 (permalink)
A True Z Fanatic
 
Ghostvette's Avatar
 
Join Date: Aug 2013
Location: Shawnee KS
Posts: 5,698
Drives: 15 Magma Red 6MT
Rep Power: 2684376
Ghostvette has a reputation beyond reputeGhostvette has a reputation beyond reputeGhostvette has a reputation beyond reputeGhostvette has a reputation beyond reputeGhostvette has a reputation beyond reputeGhostvette has a reputation beyond reputeGhostvette has a reputation beyond reputeGhostvette has a reputation beyond reputeGhostvette has a reputation beyond reputeGhostvette has a reputation beyond reputeGhostvette has a reputation beyond repute
Default

Quote:
Originally Posted by Knio View Post
Hi all,

Just going to dump my problems here...

Driving home the other day, everything seems fine until the freeway onramp when I lose all power. It feels like the fuel starvation problem that I've experienced before, and I am low on fuel.. so I coast off the freeway, and eventually it gets some power back, but it's extremely jerky and definitely not a fuel starvation problem now.

I limp back to a parking lot. The idle is not smooth and bouncing between 800-1400, and it won't rev past 3.5k at all. When I tested revving it, TCS and slip lights also come on. I turn the engine off, try to turn it back on, it will crank but not fire.

Eventually I get a code reader working and see P0300 and P0340 - Camshaft position sensor error. Check the forums and see a few posts that mention unplugging the sensors might work. I clear the DTCs and try it:

Both sensors plugged in - won't start

Bank 2 unplugged - won't start

Bank 1 unplugged - will start, but cranks for much longer than normal, and is in limp mode and won't rev past 3.5k, but the idle is smooth, and everything feels fine otherwise! This has been reproducible every time.

I swapped the left and right sensors, both looked clean and the problem is still exactly the same, and not P0345, and still runs with only bank 2 plugged in, so I think both of the sensors themselves are working.

I probed all connections with a multimeter at both harnesses for OC, SC, and the signal, at the sensors themselves, and in the ECM harness and everything looks fine, and the left & right banks match, giving more evidence that it's not a sensor or electrical problem. I don't have a scope, but the signals are 5V when off and jump around near 4.5V when the engine is running, which is what you'd expect from working sensors.

I feel like I've eliminated any electrical problems, and could it really be a timing problem since the engine runs fine and smooth up to 3.5k in limp mode? But will keep looking.. I've ordered a scope to check the actual signals, and will try to remove the timing cover to inspect the camshaft gears and timing chain this weekend. Most of the other threads I saw didn't post resolutions. I'm hoping I can fix this myself and not have to take it to a dealer :P

Car is tuned with JWT intakes, Nismo exhaust, oil cooler, 60k miles.

Other threads:

Z throw P0340 and P0345 code after violent spun out on skidpad
Car won't start & pending Code P0340
2009 base won't start
Help me diagnose this problem: I can't rev past 3500 RPM intermittently (AK370Z)
Camshaft/Crankshaft Sensor, Limp Mode, Z issues :/
Need Help - Car Stalled and wont start
When a problem doesn't move side to side, then the problem is usually wire/ECM related. Try removing the negative terminal from the battery, step on the brake pedal for 10 to 15 seconds (I don't remember exactly, there is a thread somewhere) to clear memory, then reattach cable. Try restarting the car and see what happens with both sensors plugged in. I doubt you have a timing chain issue, the car wouldn't run at all if it jumped time. If you have access to a good scanner (snap-on, MAC or Consult), that might help. GL.
__________________
2015 Magma Red 6MT Sport Tech/2012 Fairlady MB 6MT Base (RIP 08032018)https://www.nicoclub.com/FSM/370Z/Coupe/
Ghostvette is offline   Reply With Quote
Old 12-12-2019, 06:53 PM   #3 (permalink)
Base Member
 
Join Date: Jun 2018
Location: Australia
Posts: 61
Drives: 370z
Rep Power: 5363
SteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond repute
Default

The ECU seems to have an issue with bank 1 and may see it off timing for some reason and wont let you start to protect motor.
But when bank 1 signal is completely missing it uses bank 2 to work out timing for bank1 (only an approx.)and runs in limp mode. Which is why it cranks for longer.
You may have an issue with the variable valve timing on bank 1 or even jumped a tooth on the timing chain. Or ECU/wiring issues.
Could be few others things as well.
Your best to take car to an auto electrician
SteveSAS is offline   Reply With Quote
Old 12-12-2019, 08:32 PM   #4 (permalink)
Base Member
 
Knio's Avatar
 
Join Date: May 2011
Location: Palo Alto, CA
Posts: 141
Drives: 40th
Rep Power: 13
Knio has a spectacular aura aboutKnio has a spectacular aura about
Default

Thanks guys! I will double check all the wiring tomorrow when I get a scope, but so far everything still seems OK and the problem repeats even after resetting everything.

I discovered last night that the car was super low on oil.. it took almost 2 quarts before getting back up to normal and was pretty dirty. I did an oil change, but the problem persists. The low oil makes me think it could be an actual VVT problem like a gallery not getting enough oil pressure or tensioner getting clogged or something like the other threads mentioned. I'm trying to think of ways to verify the VVT before committing to tearing it all apart.
Knio is offline   Reply With Quote
Old 12-14-2019, 01:32 AM   #5 (permalink)
Base Member
 
Knio's Avatar
 
Join Date: May 2011
Location: Palo Alto, CA
Posts: 141
Drives: 40th
Rep Power: 13
Knio has a spectacular aura aboutKnio has a spectacular aura about
Default

I think I found something interesting.

I checked all the signals with a scope and they all look OK individually:

phase1.PNG

bank 1 at sensor
IMG_2156_1.JPG

bank 2 at sensor
IMG_2157_1.JPG

bank 1 at ECU
IMG_2159_1.JPG

bank 2 at ECU
IMG_2160_1.JPG

crank.PNG

crankshaft at ECU
IMG_2161_1.JPG

And then I noticed this drawing in the manual and decided to test both channels:

wave.PNG
IMG_2162_1.JPG
IMG_2163_1.JPG
IMG_2165_1.JPG
IMG_2166_1.JPG

It looks like bank2 is advanced about 2ms relative to bank1, if they're supposed to be lined up like the manual shows. this would be about 5 degrees.

I also tested phase vs crank, but these did not vary at all with RPM. maybe IVT doesn't kick in before 3500, or the ecu disables it entirely in limp mode.

I'm not really sure the 5 degree out of phase is an error or not without knowing exactly what the gears look like, but this timing could be off.
Knio is offline   Reply With Quote
Old 12-14-2019, 02:16 AM   #6 (permalink)
Base Member
 
Join Date: Jun 2018
Location: Australia
Posts: 61
Drives: 370z
Rep Power: 5363
SteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond repute
Default

Show us pic of crank sensor vs cam phase bank1 at idle.
SteveSAS is offline   Reply With Quote
Old 12-14-2019, 03:26 AM   #7 (permalink)
Base Member
 
Knio's Avatar
 
Join Date: May 2011
Location: Palo Alto, CA
Posts: 141
Drives: 40th
Rep Power: 13
Knio has a spectacular aura aboutKnio has a spectacular aura about
Default

Quote:
Originally Posted by SteveSAS View Post
Show us pic of crank sensor vs cam phase bank1 at idle.
Sorry didn’t get a pic, but bank1 started about 4 notches into the 10 notch pattern in the crank, and bank2 was 3 notches in. i’m not sure where the zero point should be or what the expected timing at idle is. Will get a pic tomorrow.
Knio is offline   Reply With Quote
Old 12-14-2019, 04:44 AM   #8 (permalink)
Base Member
 
Join Date: Jun 2018
Location: Australia
Posts: 61
Drives: 370z
Rep Power: 5363
SteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond repute
Default

Like you were saying. Both banks should be the same, just shifted 360 degrees.

Can you see the timing chain when the cam sensors are removed. I think there's a colored chain line that lines up with mark in the cam pulley.

Anyway first verify chain timing if off and why before opening engine up. Could also be a stretched chain due to high mileage. This would explain the variation in timing between banks 1 and 2.

How many miles on this car and how often is oil changed?
SteveSAS is offline   Reply With Quote
Old 12-14-2019, 04:46 AM   #9 (permalink)
Base Member
 
Join Date: Jun 2018
Location: Australia
Posts: 61
Drives: 370z
Rep Power: 5363
SteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond repute
Default

I think car will also run with both cam sensors unplugged. Try it.

And do remember this engine is an interference one so if it is jumping teeth due to loose chain you could damage engine beyond repair.

Last edited by SteveSAS; 12-14-2019 at 04:58 AM.
SteveSAS is offline   Reply With Quote
Old 12-14-2019, 04:59 AM   #10 (permalink)
Base Member
 
Join Date: Jun 2018
Location: Australia
Posts: 61
Drives: 370z
Rep Power: 5363
SteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond repute
Default

https://www.youtube.com/watch?v=GnW2NclDbi0

And

VQ37vhr timing chain

Last edited by SteveSAS; 12-14-2019 at 09:24 AM.
SteveSAS is offline   Reply With Quote
Old 12-15-2019, 10:20 PM   #11 (permalink)
Base Member
 
Knio's Avatar
 
Join Date: May 2011
Location: Palo Alto, CA
Posts: 141
Drives: 40th
Rep Power: 13
Knio has a spectacular aura aboutKnio has a spectacular aura about
Default

Thanks for the links. The car won't fire with both unplugged even after clearing and resetting everything.

Quote:
Originally Posted by SteveSAS View Post
Show us pic of crank sensor vs cam phase bank1 at idle.
These are vs bank2 but shows the phase offset

cnk_vs_cam2.jpg

IMG_2169_1.JPG
Knio is offline   Reply With Quote
Old 12-16-2019, 12:31 AM   #12 (permalink)
Base Member
 
Knio's Avatar
 
Join Date: May 2011
Location: Palo Alto, CA
Posts: 141
Drives: 40th
Rep Power: 13
Knio has a spectacular aura aboutKnio has a spectacular aura about
Default

I borrowed a friend's working G37 for a few minutes and got these traces of camshaft bank 1 vs bank 2

IMG_003_G37.BMP

g37_cam1_cam2.PNG

I think this seems to confirm that my timing is in fact off somehow, so I'll have to open it up.
Knio is offline   Reply With Quote
Old 12-16-2019, 05:33 AM   #13 (permalink)
Base Member
 
Join Date: Jun 2018
Location: Australia
Posts: 61
Drives: 370z
Rep Power: 5363
SteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond repute
Default

Yep, seem to be off by a lot. Next is to work out why?

Best to open up and see for yourself. Or get a quote to fix.

Remember to replace oil gallery gasket as this was an issue with the 08/09 models.
And something about the screws also going loose. Find out how to replace properly if you are going to replace.

And turn engine over 4 times manually and rechecking timing before closing it up.
You may need to replace chain guides a well if they are worn.
SteveSAS is offline   Reply With Quote
Old 12-16-2019, 05:35 AM   #14 (permalink)
Base Member
 
Join Date: Jun 2018
Location: Australia
Posts: 61
Drives: 370z
Rep Power: 5363
SteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond reputeSteveSAS has a reputation beyond repute
Default

How many miles on car? Water pump replacement might be a good idea.
SteveSAS is offline   Reply With Quote
Old 12-16-2019, 10:42 PM   #15 (permalink)
A True Z Fanatic
 
Join Date: Aug 2018
Location: Chicagoland
Age: 37
Posts: 5,261
Drives: A Garage Queen
Rep Power: 2684370
BettyZ has a reputation beyond reputeBettyZ has a reputation beyond reputeBettyZ has a reputation beyond reputeBettyZ has a reputation beyond reputeBettyZ has a reputation beyond reputeBettyZ has a reputation beyond reputeBettyZ has a reputation beyond reputeBettyZ has a reputation beyond reputeBettyZ has a reputation beyond reputeBettyZ has a reputation beyond reputeBettyZ has a reputation beyond repute
Default

Very cool diagnostic you ran there. There are threads here on replacing the oil gallery gaskets. I did it myself a year ago, happy to answer any questions.

You can get a gasket kit from ConceptZPerformance. And if you have $$ laying around, might be worth it to figure out what else you'd like done "while you're in there." I ended up relooming and tucking all the bay wires, replacing the belt, etc. Maybe an upgraded oil pump?...

Sent from my SM-G955U using Tapatalk
elhombre likes this.
__________________
'14 MB Nismo | Boost Lab 6870 1.32 AR 553 HP / 471 ft.-lbs.
Betty Mods
BettyZ is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Z throw P0340 and P0345 code after violent spun out on skidpad mousewei84 Engine & Drivetrain 4 05-22-2017 07:11 AM
Car won't start & pending Code P0340 AsianJedi Engine & Drivetrain 9 10-07-2016 02:30 PM
Check engine light p0345 and p0340 Glambutang Engine & Drivetrain 1 09-12-2013 09:03 PM


All times are GMT -5. The time now is 03:16 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 PL2