Help!! Shifter feels weird.

Aizen Sosuke · 07-02-2015, 09:06 PM

So my shop dropped my transmission this week and installed a new clutch kit, CSC and master. The original CSC took a crap right as the car crossed 100k mile and I took the chance to replace the original clutch and master cylinder too just to be on the safe side. In any case after everything was put together I take the car for a test drive today and the shifter is different and not in a good way.
When I try to shift from 4th to either 5th or 6th I feel like the stick travels all the way right past the 5 and 6 gate. It even goes all the way to reverse without pressing down on the shifter. This is obviously not right so I searched here and was only able to find a thread about shifter guide plates but for 350Z. Any light you guys can shed on this would be greatly appreciated.
Thanks

maizenblue · 07-02-2015, 09:38 PM

I'm not certain, but I believe it is possible to incorrectly reinstall the shifter after transmission work is done. I think I remember another member had this same issue a few months ago, at any rate take it back to the shop

Aizen Sosuke · 07-02-2015, 09:41 PM

I'll take it back the them after the Holiday weekend. I'm hoping to know what's going on before then so I could tell them.

07-02-2015, 09:06 PM	#1 (permalink)
Aizen Sosuke Base Member Join Date: Aug 2011 Location: Miami Age: 40 Posts: 189 Drives: 09 370Z Sport Rep Power: 13	Help!! Shifter feels weird. So my shop dropped my transmission this week and installed a new clutch kit, CSC and master. The original CSC took a crap right as the car crossed 100k mile and I took the chance to replace the original clutch and master cylinder too just to be on the safe side. In any case after everything was put together I take the car for a test drive today and the shifter is different and not in a good way. When I try to shift from 4th to either 5th or 6th I feel like the stick travels all the way right past the 5 and 6 gate. It even goes all the way to reverse without pressing down on the shifter. This is obviously not right so I searched here and was only able to find a thread about shifter guide plates but for 350Z. Any light you guys can shed on this would be greatly appreciated. Thanks

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
DIY: TWM Short Shifter and Leather Shifter Boot	GaleForce	DIY Section (Do-It-Yourself)	84	04-11-2018 04:42 PM
What is the best short-throw shifter and shifter knob combo?	ZInferno0248	Nissan 370Z General Discussions	79	03-06-2017 06:57 AM
Weird Shifter Issue	coloradoz	Engine & Drivetrain	12	12-28-2014 05:29 PM
does anyone know how it feels!!	shl468	Nissan 370Z General Discussions	24	03-12-2013 07:59 PM
shifter feels sloppy...	Damon	Engine & Drivetrain	8	08-26-2009 08:28 AM

07-02-2015, 09:38 PM	#2 (permalink)
maizenblue Enthusiast Member Join Date: Sep 2013 Location: Denver Posts: 288 Drives: 2010 370Z Rep Power: 11	I'm not certain, but I believe it is possible to incorrectly reinstall the shifter after transmission work is done. I think I remember another member had this same issue a few months ago, at any rate take it back to the shop

07-02-2015, 09:41 PM	#3 (permalink)
Aizen Sosuke Base Member Join Date: Aug 2011 Location: Miami Age: 40 Posts: 189 Drives: 09 370Z Sport Rep Power: 13	I'll take it back the them after the Holiday weekend. I'm hoping to know what's going on before then so I could tell them.