CJM Oil Pan

jwick · 08-12-2015, 01:17 PM

Quote:

Originally Posted by phunk

Photo of the -10 o-ring ports on the side attached.

Starting tomorrow I will have the paid units with side ports begin shipping. The plugs and adapters I ordered for those ports will be here tomorrow.

Guess it's time for me to pay so shipping can happen

phunk · 08-12-2015, 01:23 PM

Quote:

Originally Posted by jwick

Guess it's time for me to pay so shipping can happen

Since yours has to be anodized, there is no rush on your part yet.

jwick · 08-12-2015, 01:32 PM

Quote:

Originally Posted by phunk

Since yours has to be anodized, there is no rush on your part yet.

No worries. Looking back at the details list for my fittings, and this might be a obvious, the -6AN should be a male fitting for a swivel AN hose fitting and the 1/8NPT should be a female fitting to accept my temperature probe.

patabq · 08-12-2015, 02:10 PM

paid for black anodized

ban25 · 08-12-2015, 04:36 PM

Just sent a PM, I'd love to get on the list for a black anodized pan!

Mike · 08-12-2015, 04:55 PM

Quote:

Originally Posted by ban25

Just sent a PM, I'd love to get on the list for a black anodized pan!

you can buy mine if you want. Just pay phunk whatever extra it is for anodizing, and reimburse me the original amount.
I want to go V8 when my engine blows, and this isn't going to help that!

ban25 · 08-12-2015, 06:43 PM

Quote:

Originally Posted by Mike

you can buy mine if you want. Just pay phunk whatever extra it is for anodizing, and reimburse me the original amount.
I want to go V8 when my engine blows, and this isn't going to help that!

Actually, I just got the last one from phunk...

ENT-Z · 08-12-2015, 07:53 PM

Quote:

Originally Posted by Mike

you can buy mine if you want. Just pay phunk whatever extra it is for anodizing, and reimburse me the original amount.
I want to go V8 when my engine blows, and this isn't going to help that!

Mike if you make a plan for when your engine blows, your engine will never blow!!

phunk · 08-12-2015, 08:18 PM

Yes the last unit has been sold... so anyone else who wants one, I would recommend waiting a few weeks to place the order. There will be 12 more going into production in a few weeks... material is here.

edit: one more might become available, I will post up if it does

jwick · 08-12-2015, 08:27 PM

Quote:

Originally Posted by ENT-Z

Mike if you make a plan for when your engine blows, your engine will never blow!!

Yeah just ask djtodd. Spare motor waiting to go in after pops the stock one. 660whp all track miles still going strong.

phunk · 08-12-2015, 08:33 PM

Quote:

Originally Posted by jwick

Yeah just ask djtodd. Spare motor waiting to go in after pops the stock one. 660whp all track miles still going strong.

How much power does he run the car at on the track? 660whp can barely hook up with 28" drag tires and zero camber.. id be surprised if anyone tracked a 370z over 525rwhp or so. Grip would be impossible

jwick · 08-12-2015, 08:36 PM

Quote:

Originally Posted by phunk

How much power does he run the car at on the track? 660whp can barely hook up with 28" drag tires and zero camber.. id be surprised if anyone tracked a 370z over 525rwhp or so. Grip would be impossible

He might have a low boost setting. I know the final E85 tune from FI was like 659whp and some 550ish wtq.

Maybe he'll stumble across and respond.

phunk · 08-12-2015, 08:38 PM

Quote:

Originally Posted by jwick

He might have a low boost setting. I know the final E85 tune from FI was like 659whp and some 550ish wtq.

Maybe he'll stumble across and respond.

Ya that would be like one of the most extreme cars on the road course to run it that way... would probably need full aero widebody slicks and a very custom fuel surge solution to move a rwd car around a road course at that power!

DR_ · 08-12-2015, 09:02 PM

Got my CJ oil pan today. Thanks phunk for the piece of art work! Now I have to take a crack at getting off the stock oil pan. Last time I tried I couldn't get anything in there to pry it off.
Any recommendations on what kind of gasket to use when putting it back on?

Rusty · 08-12-2015, 09:13 PM

Quote:

Originally Posted by DR_

Got my CJ oil pan today. Thanks phunk for the piece of art work! Now I have to take a crack at getting off the stock oil pan. Last time I tried I couldn't get anything in there to pry it off.
Any recommendations on what kind of gasket to use when putting it back on?

A thin bladed screwdriver and a hammer. Once one section starts to lift. Go to another spot and try there. You don't want to put all the pressure in one spot. Also leave about 4 bolts in, loose. This way way when the pan pops loose. It won't make a mess. If you mark up the mating surface. Use a small very fine file to knock down the burr. For sealing. Use an rtv that is O2 sensor safe. I used the black rtv.

08-12-2015, 08:18 PM	#309 (permalink)
phunk A True Z Fanatic Join Date: Mar 2009 Location: Chicago Posts: 3,657 Drives: 370 Rep Power: 947878	Yes the last unit has been sold... so anyone else who wants one, I would recommend waiting a few weeks to place the order. There will be 12 more going into production in a few weeks... material is here. edit: one more might become available, I will post up if it does GaleForce likes this. __________________ Charles @ CJ Motorsports : Website \| Facebook \| Instagram \| YouTube Home of the 9 second, stock longblock, stock drivetrain 6MT 370z. 9.91 @ 142mph Last edited by phunk; 08-12-2015 at 08:25 PM.

08-12-2015, 09:02 PM	#314 (permalink)
DR_ Track Member Join Date: Jul 2009 Location: Dallas Posts: 981 Drives: Touring/Sport M6 PG Rep Power: 16	Got my CJ oil pan today. Thanks phunk for the piece of art work! Now I have to take a crack at getting off the stock oil pan. Last time I tried I couldn't get anything in there to pry it off. Any recommendations on what kind of gasket to use when putting it back on? phunk likes this.

08-12-2015, 02:10 PM	#304 (permalink)
patabq Base Member Join Date: Jun 2015 Location: Albuquerque, NM Posts: 63 Drives: Corvette Z06 07 Rep Power: 9	paid for black anodized

08-12-2015, 04:36 PM	#305 (permalink)
ban25 Enthusiast Member Join Date: Nov 2009 Location: SF, CA Posts: 339 Drives: 17 C7 Z06 M7 Rep Power: 65	Just sent a PM, I'd love to get on the list for a black anodized pan!