Z1 Motorsports: Clutch Concentric Slave Cylinder Elimination Kit

John@Z1 · 04-30-2014, 10:43 AM

Quote:

Originally Posted by wheee!

These thing look awesome....

Thank you sir!

EVOR · 04-30-2014, 06:37 PM

Need a set soon

John@Z1 · 05-06-2014, 09:53 AM

Quote:

Originally Posted by EVOR

Need a set soon

Hit us up at any time!

cavemancan · 05-06-2014, 02:53 PM

Quote:

Originally Posted by cavemancan

Thanks for the input! Pedal feel alone justifies the cost for me.

This will mark the 3rd time the slave/master cylinder will need to be replaced on my car. 2 of which were under warranty. This last time I am out of factory warranty and I am left with my extended warranty but they are telling me it is not covered. Either way I think I am going to forgo the drama and just buy this. Have to save some pennies for the whole setup though. I plan to change the clutch, flywheel, CSC, and Master cylinder.

Last 3 question(s):
- Do you recommend rebuilding the master cylinder or replacing? I saw a rebuild kit for $18 which is better then paying $110 for a new one.
- Do you guys sell stock clutches? I plan to race the car NA but keep it a daily driver.
- Any suggestion for an upgraded clutch? I may consider an upgrade just trying to keep cost down.

Just wanted to see if you saw these questions...

JARblue · 05-06-2014, 03:04 PM

John, can you please explain the pros/cons of the CMC rebuild kit vs buying a new assembly?

John@Z1 · 05-07-2014, 09:03 AM

Quote:

Originally Posted by cavemancan

Just wanted to see if you saw these questions...

I missed those

Originally Posted by cavemancan View Post
Thanks for the input! Pedal feel alone justifies the cost for me.

This will mark the 3rd time the slave/master cylinder will need to be replaced on my car. 2 of which were under warranty. This last time I am out of factory warranty and I am left with my extended warranty but they are telling me it is not covered. Either way I think I am going to forgo the drama and just buy this. Have to save some pennies for the whole setup though. I plan to change the clutch, flywheel, CSC, and Master cylinder.

Last 3 question(s):
- Do you recommend rebuilding the master cylinder or replacing? I saw a rebuild kit for $18 which is better then paying $110 for a new one.
- Do you guys sell stock clutches? I plan to race the car NA but keep it a daily driver.
- Any suggestion for an upgraded clutch? I may consider an upgrade just trying to keep cost down.

Rebuilding or replacing the master cylinder is never a bad idea on the Z34 as they are known to have problems. I will say that we have never had to replace the master on the Z1 shop car and it has 36K ABUSED and track tested miles.

I would suggest the Z1 clutch and flywheel combo over going with a stocker as the Z1 flywheel will allow for quicker revs.

John@Z1 · 05-07-2014, 09:09 AM

Quote:

Originally Posted by JARblue

John, can you please explain the pros/cons of the CMC rebuild kit vs buying a new assembly?

I'm a busy guy which means I would just buy a new one to install as time is not a very big thing that I have on my hand. If you have a little garage time for yourself the rebuild kit may be the best for you.

JARblue · 05-07-2014, 09:34 AM

Quote:

Originally Posted by John@Z1

I'm a busy guy which means I would just buy a new one to install as time is not a very big thing that I have on my hand. If you have a little garage time for yourself the rebuild kit may be the best for you.

Thanks for the response, John. I understand. I'm convinced my CSC is going to fail soon, as well, so I'm probably just going to order your kit asap.

Can you please PM me a price for the CSC elimination kit plus an OEM CMC assembly shipped to 78731? It looks like the kit comes with a SS clutch line, but if not, please include that as well. I can't think of anything else, but if there is something you think of that would be good to go ahead and do while the transmission is out, let me know (I'll be good with the stock clutch for a while).

Thanks

John@Z1 · 05-07-2014, 11:26 AM

Quote:

Originally Posted by JARblue

Thanks for the response, John. I understand. I'm convinced my CSC is going to fail soon, as well, so I'm probably just going to order your kit asap.

Can you please PM me a price for the CSC elimination kit plus an OEM CMC assembly shipped to 78731? It looks like the kit comes with a SS clutch line, but if not, please include that as well. I can't think of anything else, but if there is something you think of that would be good to go ahead and do while the transmission is out, let me know (I'll be good with the stock clutch for a while).

Thanks

Thanks for the call sir!

cavemancan · 05-07-2014, 02:17 PM

Quote:

Originally Posted by John@Z1

I missed those

Originally Posted by cavemancan View Post

Last 3 question(s):
- Do you recommend rebuilding the master cylinder or replacing? I saw a rebuild kit for $18 which is better then paying $110 for a new one.
- Do you guys sell stock clutches? I plan to race the car NA but keep it a daily driver.
- Any suggestion for an upgraded clutch? I may consider an upgrade just trying to keep cost down.

Rebuilding or replacing the master cylinder is never a bad idea on the Z34 as they are known to have problems. I will say that we have never had to replace the master on the Z1 shop car and it has 36K ABUSED and track tested miles.

I would suggest the Z1 clutch and flywheel combo over going with a stocker as the Z1 flywheel will allow for quicker revs.

John,

Thanks again for the help!

Can you quote the following to 33186
- CSC elimination kit
- Z1 clutch/flywheel combo (Does this include the clutch/flywheel install tool? If not please include)
- Steel braided clutch line (Is this included in the CSC kit? If not please include)
- Trany fluid and crush washers (redline)
- Diff fluid and crush washers (redline)

Am I missing anything?

Thanks!

Chris

P.S. Can you include wheel spacers? 20mm rear and 15mm front.
P.S.S What is the difference between the standard full face and lightweight solid hub full face aside from the obvious weight savings?

John@Z1 · 05-07-2014, 03:30 PM

Quote:

Originally Posted by cavemancan

John,

Thanks again for the help!

Can you quote the following to 33186
- CSC elimination kit
- Z1 clutch/flywheel combo (Does this include the clutch/flywheel install tool? If not please include)
- Steel braided clutch line (Is this included in the CSC kit? If not please include)
- Trany fluid and crush washers (redline)
- Diff fluid and crush washers (redline)

Am I missing anything?

Thanks!

Chris

P.S. Can you include wheel spacers? 20mm rear and 15mm front.
P.S.S What is the difference between the standard full face and lightweight solid hub full face aside from the obvious weight savings?

PM sent!

Redsmoke89 · 05-07-2014, 03:54 PM

My review after break in and one autocross event:

So to start off a little background story, this is my first manual car. I learned how to drive on the stock clutch. So obviously changing the feel of it scared me a bit. I got the spec stage 1 clutch and their steel flywheel, along with my Z1 CSC elimination kit. Now the pedal feel is obviously night and day to what it used to be. No sloppy pedal feel and the engagement point is now closer to the bottom. The clutch is firm to a comfortable point and I can feel where it engages much better. Also after the 500 mile break in I had one autocross event where the car performed very well, no issues with clutch related tasks all day. Overall the kit gives me the peace of mind knowing I won’t have a CSC fail while I am driving and it is so far a great investment. If you guys have any questions about how it performs feel free to PM me! Great job Z1 this is an awesome product!

John@Z1 · 05-08-2014, 09:41 AM

Quote:

Originally Posted by Redsmoke89

My review after break in and one autocross event:

So to start off a little background story, this is my first manual car. I learned how to drive on the stock clutch. So obviously changing the feel of it scared me a bit. I got the spec stage 1 clutch and their steel flywheel, along with my Z1 CSC elimination kit. Now the pedal feel is obviously night and day to what it used to be. No sloppy pedal feel and the engagement point is now closer to the bottom. The clutch is firm to a comfortable point and I can feel where it engages much better. Also after the 500 mile break in I had one autocross event where the car performed very well, no issues with clutch related tasks all day. Overall the kit gives me the peace of mind knowing I won’t have a CSC fail while I am driving and it is so far a great investment. If you guys have any questions about how it performs feel free to PM me! Great job Z1 this is an awesome product!

Thanks for the feedback Redsmoke89!

John@Z1 · 05-13-2014, 08:08 AM

In stock!

JARblue · 05-13-2014, 08:15 AM

Quote:

Originally Posted by John@Z1

In stock!

I will be calling you shortly to place my order

*edit* Ordered! Thanks for the help, John

04-30-2014, 06:37 PM	#32 (permalink)
EVOR A True Z Fanatic Join Date: Sep 2009 Location: New York Posts: 1,647 Drives: 09 Nismo 370Z #80 Rep Power: 44	Need a set soon __________________ WWW.EVO-R.NET

05-06-2014, 03:04 PM	#35 (permalink)
JARblue A True Z Fanatic Join Date: Mar 2011 Location: Austin, TX Age: 43 Posts: 36,449 Drives: 11 Z34, 98 E36 M3 Rep Power: 2684440	John, can you please explain the pros/cons of the CMC rebuild kit vs buying a new assembly? __________________ 2011 370Z 6MT Sport Gun Metallic \| ARC \| CJM \| Ecutek \| FI \| Fujimura \| R2C \| SPL \| Stillen \| TWM \| Z1 \| ZSpeed \|

05-07-2014, 03:54 PM	#42 (permalink)
Redsmoke89 Base Member Join Date: Apr 2013 Location: GA Posts: 31 Drives: 09 370z Base Sport Rep Power: 12	My review after break in and one autocross event: So to start off a little background story, this is my first manual car. I learned how to drive on the stock clutch. So obviously changing the feel of it scared me a bit. I got the spec stage 1 clutch and their steel flywheel, along with my Z1 CSC elimination kit. Now the pedal feel is obviously night and day to what it used to be. No sloppy pedal feel and the engagement point is now closer to the bottom. The clutch is firm to a comfortable point and I can feel where it engages much better. Also after the 500 mile break in I had one autocross event where the car performed very well, no issues with clutch related tasks all day. Overall the kit gives me the peace of mind knowing I won’t have a CSC fail while I am driving and it is so far a great investment. If you guys have any questions about how it performs feel free to PM me! Great job Z1 this is an awesome product! John@Z1 likes this. __________________ Eibach Sway Bars / Swift Springs / Injen Intake / Berk HFC

05-13-2014, 08:08 AM	#44 (permalink)
John@Z1 The370Z.com Sponsor Join Date: Nov 2008 Location: GA Posts: 1,589 Drives: Turbos Rep Power: 19	In stock! __________________ Z1 Motorsports will beat any advertised price on Nissan OEM Parts! 770-838-7777 ext 311 AIM: JohnatZ1 email: John@Z1motorsports.com

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Clutch Slave cylinder broke @ 22K	chknhawk	Engine & Drivetrain	37	07-10-2018 10:46 AM
Clutch Slave Cylinder	Wiggins3377	Engine & Drivetrain	18	08-06-2015 09:26 AM
Clutch, Flywheel, and Slave Cylinder Combo Sale at R/T Tuning.	Erik@RTTuning	R/T Tuning	6	12-26-2012 12:10 PM
Clutch slave cylinder	NizzyBoy	Engine & Drivetrain	1	02-19-2011 02:24 PM