DIY: Headlight LED's and blackout

Geoff-R · 12-28-2012, 11:39 AM

What MCD rating do you guys recommend for these LEDs, I notice the OP has 4000 MCD and there have been other ratings used.

AlexRaymond19 · 01-12-2013, 02:19 PM

Hey guys, finally found some time to tear my headlights apart... Got the first one apart and i'm painting it now. What adhesive should i use to put it back together? Will i be fine with just reheating the old stuff? Or should i pick something different up. I want to use something that will allow me to get back into the lights if need be. Thanks

FairladyZ · 01-12-2013, 02:28 PM

Quote:

Originally Posted by AlexRaymond19

Hey guys, finally found some time to tear my headlights apart... Got the first one apart and i'm painting it now. What adhesive should i use to put it back together? Will i be fine with just reheating the old stuff? Or should i pick something different up. I want to use something that will allow me to get back into the lights if need be. Thanks

Old stuff is fine just press hard

kellster · 01-21-2013, 07:51 AM

Getting ready to tackle this project in a couple of weeks. I'm gonna color match the bezels magma red, but haven't decided if I want the reflectors satin black or match them to the new gunmetal NISMO wheels. What do you guy think?

AlexRaymond19 · 01-24-2013, 09:47 AM

Quote:

Originally Posted by kellster

Getting ready to tackle this project in a couple of weeks. I'm gonna color match the bezels magma red, but haven't decided if I want the reflectors satin black or match them to the new gunmetal NISMO wheels. What do you guy think?

black, and leave the silver trim piece that runs the length of the reflector! It looks very sharp that way

RJ89 · 02-17-2013, 08:06 PM

Just finished this up last night and figured I'd put a picture up to show the final product... awesome instructions by the way Caravanshaka, as well as all of the removal instructions for everything else. Even though its a night-time photo, did a black house and the lights!

Saltee · 03-10-2013, 07:29 PM

Doing this to my car as well here are some tips i learned in case you were too:

Firstly.. to avoid confusion the red wire is your hot ( or positive ) and the black should be the negative...
therefore the resistor should go on the red wire

Secondly.. these bulbs have a positive and negative side: the side with the longer stem is the positive and it is vital they are all in the same direction

Thirdly.. there only needs to be 1 resistor in the beginning of the circuit in between the power source and first set of lights on the chain... if you add a resistor to each whip (row of lights) they will get duller as you go further from the source due to the retarding of power through the resistor...

lastly.. LEAVE ENOUGH SLACK in order to get the bulbs into the right place.. i just ripped apart my work as i had leaned these 3 tips the hard way.. i will post pics later for those interested?

emotionr · 06-07-2013, 03:43 PM

I give you props on this. However, there are already after-market headlights with all this pre-assembled and fitted... Again, props to you buddy! GJ!

willie646 · 07-26-2013, 08:47 PM

awesome instructions came out very nice, but one problem the led's recommended are not bright at all, cant tell its on during the day. any recommendations on brighter led's that will work.

khanhvu411 · 07-28-2013, 02:10 PM

Maybe you didn't angle the correctly? Mine are pretty good even under the sun light (of course they wont be as bright as audi's)

willie646 · 08-01-2013, 12:13 PM

no matter what angle you look at them they are not bright at all. on a sunny day you have to look really hard to be able to tell they are on.

pfdaxe · 08-01-2013, 12:28 PM

Mine are fine...

willie646 · 08-06-2013, 12:16 PM

wow mine looks nothing like the pic pfdake has. nice !!!!!

jaedub · 10-09-2013, 01:42 AM

Work in progress! Finished with setting up LEDs

http://www.the370z.com/attachment.ph...1&d=1381644572

Smartace3 · 10-20-2013, 01:24 PM

For those of you that used Krylon fusion paint.. How has it been holding up?? Any chipping, peeling, cracking, fading from the heat of the lights?? Im planning on doing this to my headlights and wanted to know the best route to take. Thanks.

12-28-2012, 11:39 AM	#196 (permalink)
Geoff-R Base Member Join Date: Jun 2010 Location: UK Posts: 29 Drives: 10 Nissan 370Z Black Rep Power: 15	What MCD rating do you guys recommend for these LEDs, I notice the OP has 4000 MCD and there have been other ratings used. __________________ 370Z Black Edition - no. 52/370

01-12-2013, 02:19 PM	#197 (permalink)
AlexRaymond19 Track Member Join Date: Jun 2011 Location: Maine Posts: 771 Drives: 2010 Nissan 370z Rep Power: 16	Hey guys, finally found some time to tear my headlights apart... Got the first one apart and i'm painting it now. What adhesive should i use to put it back together? Will i be fine with just reheating the old stuff? Or should i pick something different up. I want to use something that will allow me to get back into the lights if need be. Thanks __________________ 2010 370Z Touring MT \| Stillen \| Motordyne \| Momentum\| Z1 \| Fast Intentions \| Advant Garde \| RE11 \| Swift \| SPC \| Quaife \| Whiteline \| Evo R \| 322RWHP 259ft-lb Mustang

08-01-2013, 12:28 PM	#207 (permalink)
pfdaxe A True Z Fanatic Join Date: Aug 2012 Location: Phoenix, AZ Posts: 1,070 Drives: 09 Touring AT Sport Rep Power: 16	Mine are fine... __________________ Build Thread: http://www.the370z.com/members-370z-...xes-build.html

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
DIY: Headlight Removal	DIGItonium	DIY Section (Do-It-Yourself)	34	09-03-2017 08:01 PM
180 Custom Headlight Review!	bullitt5897	Exterior & Interior	43	12-10-2010 05:26 PM
Blacked out headlight for PG !!!	msl82	Exterior & Interior	31	05-02-2009 06:06 PM
Blacked out headlight	msl82	Nissan 370Z General Discussions	6	01-02-2009 12:47 PM

01-21-2013, 07:51 AM	#199 (permalink)
kellster Base Member Join Date: Dec 2012 Location: Houston, TX Posts: 10 Drives: 13 NISMO MR M6 #295 Rep Power: 13	Getting ready to tackle this project in a couple of weeks. I'm gonna color match the bezels magma red, but haven't decided if I want the reflectors satin black or match them to the new gunmetal NISMO wheels. What do you guy think?

02-17-2013, 08:06 PM	#201 (permalink)
RJ89 Base Member Join Date: Dec 2012 Location: Vegas Posts: 26 Drives: '13 Touring/Sport Z Rep Power: 13	Just finished this up last night and figured I'd put a picture up to show the final product... awesome instructions by the way Caravanshaka, as well as all of the removal instructions for everything else. Even though its a night-time photo, did a black house and the lights!

03-10-2013, 07:29 PM	#202 (permalink)
Saltee Base Member Join Date: Jan 2013 Location: Long Island Posts: 119 Drives: 09 370z Rep Power: 13	Doing this to my car as well here are some tips i learned in case you were too: Firstly.. to avoid confusion the red wire is your hot ( or positive ) and the black should be the negative... therefore the resistor should go on the red wire Secondly.. these bulbs have a positive and negative side: the side with the longer stem is the positive and it is vital they are all in the same direction Thirdly.. there only needs to be 1 resistor in the beginning of the circuit in between the power source and first set of lights on the chain... if you add a resistor to each whip (row of lights) they will get duller as you go further from the source due to the retarding of power through the resistor... lastly.. LEAVE ENOUGH SLACK in order to get the bulbs into the right place.. i just ripped apart my work as i had leaned these 3 tips the hard way.. i will post pics later for those interested?

06-07-2013, 03:43 PM	#203 (permalink)
emotionr Base Member Join Date: May 2013 Location: san antonio Posts: 28 Drives: Z Rep Power: 13	I give you props on this. However, there are already after-market headlights with all this pre-assembled and fitted... Again, props to you buddy! GJ!

07-26-2013, 08:47 PM	#204 (permalink)
willie646 Base Member Join Date: Jun 2013 Location: NJ Posts: 3 Drives: nissan 370z Rep Power: 13	awesome instructions came out very nice, but one problem the led's recommended are not bright at all, cant tell its on during the day. any recommendations on brighter led's that will work.

07-28-2013, 02:10 PM	#205 (permalink)
khanhvu411 Base Member Join Date: Sep 2012 Location: houston Posts: 144 Drives: 2010 370z Roadster Rep Power: 13	Maybe you didn't angle the correctly? Mine are pretty good even under the sun light (of course they wont be as bright as audi's)

08-01-2013, 12:13 PM	#206 (permalink)
willie646 Base Member Join Date: Jun 2013 Location: NJ Posts: 3 Drives: nissan 370z Rep Power: 13	no matter what angle you look at them they are not bright at all. on a sunny day you have to look really hard to be able to tell they are on.

08-06-2013, 12:16 PM	#208 (permalink)
willie646 Base Member Join Date: Jun 2013 Location: NJ Posts: 3 Drives: nissan 370z Rep Power: 13	wow mine looks nothing like the pic pfdake has. nice !!!!!

10-20-2013, 01:24 PM	#210 (permalink)
Smartace3 Base Member Join Date: Aug 2013 Location: Sacramento, CA Posts: 25 Drives: 2010 370z Coupe Rep Power: 12	For those of you that used Krylon fusion paint.. How has it been holding up?? Any chipping, peeling, cracking, fading from the heat of the lights?? Im planning on doing this to my headlights and wanted to know the best route to take. Thanks.