DIY: LED Halo w/Video's

JohnVuster · 02-10-2016, 09:15 PM

Sorry to ressurect this thread but I'm wondering about updates from anyone. Wondering how long everyone's halo lasted before one LED burnt or several LEDs burnt or until the entire halo died off? Please also include brand!

eastwest2300 · 05-24-2016, 06:15 PM

bump... will be doing this mod very soon.

Meulen · 05-25-2016, 07:48 AM

Quote:

Originally Posted by JohnVuster

Sorry to ressurect this thread but I'm wondering about updates from anyone. Wondering how long everyone's halo lasted before one LED burnt or several LEDs burnt or until the entire halo died off? Please also include brand!

going on 2 years with all the recommendations from this thread for halos, building materials. I had one out for a day, it came back on and hasn't gone out for at least 6 months now. No problems with paint melting on balast either with the way I covered the upper lens with the diffuser and used professional automotive paint/process.

JSON · 07-07-2016, 02:34 AM

Quote:

Originally Posted by Meulen

They are really turning out great! Can't wait to finish up with the halo debacle!

Little video for ya
http://youtu.be/_QyDSkILN5A

That's really cool. Which controller did you get for the demon eyes, btw? Also, how does the white look with the RGB LED strip?

I was thinking about getting RGBW strip and use 6 LEDs (if they fit), so I can get pure white and also different colors.

Thanks

JSON · 07-07-2016, 03:56 AM

Omg, great thread, but I just spent hours reading every single comment on all 42 pages of this thread after contemplating buying someone's already modified headlights locally. Thanks for all the detailed info guys, especially Nut_N_Much, VDC_OFF (Mikael), Meulen, and others I'm forgetting.

Now I'm gonna be tired as hell at work tomorrow....

Quote:

Originally Posted by VDC_OFF

Dont use vinyl. It gets soft with heat and our headlights gets hot. Recently tried it with 3m primer and edge sealer and it still showed some bubbling.

Also Datsun, youll have to dremel sand those little tabs for our cars. Not hard but just another step to add.

Also guys, if ordering from theretrofit, order some Xchange relays switchbacks. Its not good to just run leds to the parking light because leds fail with heat and the Xchange will switch off the leds when the low beam turns on. This will save you from having to replace them soon for leds going out.

I was thinking about ordering the XSB. Is it bad to run it all the time as DRL?

Also, for the RGB demon eyes or XC halos, how does the white look? I want RGB demons, but also want white for normal DRL.

Thanks again!

Meulen · 07-07-2016, 07:29 AM

Quote:

Originally Posted by JSON

That's really cool. Which controller did you get for the demon eyes, btw? Also, how does the white look with the RGB LED strip?

I was thinking about getting RGBW strip and use 6 LEDs (if they fit), so I can get pure white and also different colors.

Thanks

thanks, here's a link to the projects parts list.

Meulen's 40th journal

I did these quite some time ago though now. So I'm not sure if those are the same parts available today or those links are any good.

mmares94 · 07-14-2016, 11:59 AM

I have the HALOS Morimoto XC RBG, from retro fit source, and the Demon eyes Morimoto XC. what options do I have for powering them? I know about soldering what else can I do?

ShuuraRG · 02-26-2017, 02:04 PM

Does anyone who've done this have pics of where you've wired them in to a 12v line? I'd done this to my G37, but the connection was temporarily connected directly to the battery. I had fuse taps, but ended up trading in the car prior to properly wiring them in. I will be tackling this project yet again, this time on the Z, in a few weeks and wanted to know where people generally tap into a 12v line.

thanks!

ShuuraRG · 02-26-2017, 05:23 PM

Testing - https://www.youtube.com/watch?v=PhQliyHB4UE

apatter8 · 03-01-2017, 09:59 PM

Finally decided to give this a whirl. Got my XSBs in this week, looking to get started this weeked.

Has anyone successfully wired in the switchbacks and gotten them to work properly? This thread kind of died down before the XSBs took off. I found a video of them working properly, but no instructions or details are given: https://www.youtube.com/watch?v=LtpnEJZX72c

Also, the installation guide specifically tells you not to use glue to secure the halos. Has this always been the case, even with the older halos?

kooko · 03-14-2017, 05:45 PM

Has anybody wired their halos to their drls? I have a 2014.

apatter8 · 03-23-2017, 02:37 PM

Heed the warnings on page 39 of this thread and avoid the switchbacks. Mine worked perfectly before I sealed up the headlights, but after sealing and reinstalling they no longer work. So now I'm kind of screwed.

kooko · 03-24-2017, 11:48 AM

Quote:

Originally Posted by apatter8

Heed the warnings on page 39 of this thread and avoid the switchbacks. Mine worked perfectly before I sealed up the headlights, but after sealing and reinstalling they no longer work. So now I'm kind of screwed.

Im currently one headlight into the process and trying to finalize how im gonna wire them up. I will prob just tape resistor inside and run its wires outside of the headlights so I can wire them up any way I want incase I change my mind.

kooko · 03-24-2017, 11:58 AM

Also, a pic of how I attached XSB 3.0s to the shroud incase anybody wondered.

apatter8 · 03-24-2017, 01:42 PM

Quote:

Originally Posted by kooko

Im currently one headlight into the process and trying to finalize how im gonna wire them up. I will prob just tape resistor inside and run its wires outside of the headlights so I can wire them up any way I want incase I change my mind.

Not a bad idea at all.

Quote:

Originally Posted by kooko

Also, a pic of how I attached XSB 3.0s to the shroud incase anybody wondered.

I ended up dremel-ing out the recessed area to get them to fit. More work, but it looks nice. Also, they fit so snugly that they "snapped" into place and I probably didn't even need to use glue (although I did just to be sure).

05-24-2016, 06:15 PM	#617 (permalink)
eastwest2300 A True Z Fanatic Join Date: May 2010 Location: South FL Posts: 91,031 Drives: '16QX70/'21 Supra3.0 Rep Power: 2684552	bump... will be doing this mod very soon. __________________ Infiniti QX70 & Toyota Supra 3.0 Premium

07-14-2016, 11:59 AM	#622 (permalink)
mmares94 Base Member Join Date: Feb 2015 Location: Little Rock, Arkansas Posts: 74 Drives: 09 370Z PG MT Rep Power: 11	I have the HALOS Morimoto XC RBG, from retro fit source, and the Demon eyes Morimoto XC. what options do I have for powering them? I know about soldering what else can I do? __________________ 2009 Nissan 370z Touring Sport: Platinum Graphite: K&N CAI: Stillen Exhaust: Red GTR Button

03-14-2017, 05:45 PM	#626 (permalink)
kooko Base Member Join Date: Jan 2014 Location: Cypress Posts: 35 Drives: 14 370z MR 7AT Rep Power: 12	Has anybody wired their halos to their drls? I have a 2014. Kid_pistol131 likes this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Halo kit	rikkiphan1506	Exterior & Interior	3	01-31-2013 11:31 PM
Halo 4	The Dimer	The Lounge (Off Topic)	6	03-05-2012 03:41 PM
Z elininator drag Video's	Z eliminator	Canada	0	08-15-2010 03:41 PM
How To detailing video's	Kyle@STILLEN	Detailing / Washing / Waxing / Cosmetic Maintenance and Repair	2	03-02-2010 12:07 AM
Video's of the new arrival?	Shortbus	Nissan 370Z General Discussions	1	01-04-2009 05:14 PM

02-10-2016, 09:15 PM	#616 (permalink)
JohnVuster Base Member Join Date: Feb 2015 Location: California Posts: 7 Drives: 10 370z Rep Power: 11	Sorry to ressurect this thread but I'm wondering about updates from anyone. Wondering how long everyone's halo lasted before one LED burnt or several LEDs burnt or until the entire halo died off? Please also include brand!

02-26-2017, 02:04 PM	#623 (permalink)
ShuuraRG Base Member Join Date: Oct 2016 Location: Pickerington, OH Posts: 101 Drives: 2015 370Z NISMO Rep Power: 3364	Does anyone who've done this have pics of where you've wired them in to a 12v line? I'd done this to my G37, but the connection was temporarily connected directly to the battery. I had fuse taps, but ended up trading in the car prior to properly wiring them in. I will be tackling this project yet again, this time on the Z, in a few weeks and wanted to know where people generally tap into a 12v line. thanks!

02-26-2017, 05:23 PM	#624 (permalink)
ShuuraRG Base Member Join Date: Oct 2016 Location: Pickerington, OH Posts: 101 Drives: 2015 370Z NISMO Rep Power: 3364	Testing - https://www.youtube.com/watch?v=PhQliyHB4UE

03-01-2017, 09:59 PM	#625 (permalink)
apatter8 Base Member Join Date: Apr 2012 Location: Chattanooga, TN Posts: 106 Drives: 09 370Z Sport 6MT Rep Power: 14	Finally decided to give this a whirl. Got my XSBs in this week, looking to get started this weeked. Has anyone successfully wired in the switchbacks and gotten them to work properly? This thread kind of died down before the XSBs took off. I found a video of them working properly, but no instructions or details are given: https://www.youtube.com/watch?v=LtpnEJZX72c Also, the installation guide specifically tells you not to use glue to secure the halos. Has this always been the case, even with the older halos?

03-23-2017, 02:37 PM	#627 (permalink)
apatter8 Base Member Join Date: Apr 2012 Location: Chattanooga, TN Posts: 106 Drives: 09 370Z Sport 6MT Rep Power: 14	Heed the warnings on page 39 of this thread and avoid the switchbacks. Mine worked perfectly before I sealed up the headlights, but after sealing and reinstalling they no longer work. So now I'm kind of screwed.

03-24-2017, 11:58 AM	#629 (permalink)
kooko Base Member Join Date: Jan 2014 Location: Cypress Posts: 35 Drives: 14 370z MR 7AT Rep Power: 12	Also, a pic of how I attached XSB 3.0s to the shroud incase anybody wondered.