DIY: Door handles (disassemble, paint, reassemble & swap out)

OldGuyFla · 02-18-2017, 08:49 AM

Quote:

Originally Posted by SINISTER

Best DIY on this subject learned allot very complete!

How is the paint holding up?

Thanks for the input. The handles look great. By using the 2K clear it is basically the same clear that a body shop would be using. The shine is matching the body really good.
If you would like some current photos just let me know.

Dan

OldGuyFla · 02-18-2017, 08:58 AM

Quote:

Originally Posted by Jayhovah

Very interested in how this paint holds up... that is my only real fear in going with the DIY spray can stuff... I worry that it will be softer and less durable compared to a pro job.

I know what you mean about using the cans. It took me a while to decide on doing it that way, but I am really happy with the way it came out. As for the hardness of the clear coat. I sprayed a test piece as I went along & I have been testing how it has cured. Currently I can press my fingernail into the test piece with a good amount of pressure & barely see an imprint.

Dan

fork · 04-12-2018, 07:02 PM

First I would like to say that this was an excellent DIY write up. I followed it almost to a T.

I had enough foresight before I began this endeavor to buy a set of handles for me to work on as time permitted so that I could leave the handles on the car. That paid off big time for me as what I had hoped would be a straight forward operation took twice as long and cost twice as much as I was expecting.

The disassembly of the extra set of handles was straight forward. The only problem I ran into was that only one of the screws had a liberal amount of thread lock on it and the knurled nut insert ended up splitting the the plastic of the handle before the screw came loose. It was an easy repair for that and I disassembled the handles the same way as the OP. I also used 4-40 screws to replace the rivets on both handles.

I ordered the non-metal spray paint kit from PaintScratch in my car's body color (Deep Blue Pearl). The website even gives the option to put in your car's VIN which would give the correct paint formula for the paint (they say). I sanded the handles, cleaned them, used the supplied degreaser, applied the adhesion promoter and put primer on all as instructed. I put down four coats of the base color and had very good coverage on the handles. But the color just didn't seem to match the car. The spray color was almost like a crayola crayon kind of blue. It was a blue blue that didn't have much of the metallic fleck effect that the paint on the car has. I am a paint newbie and thought the clear would give it deepen the color and give it that sparkle. So I went to spray the clear. The spray kit from PaintScratch comes with a spray gun that you can attach to the top of the spray cans. I had successfully attached the gun to the primer can and the base color can. When I went to attach the spray gun to the clear can and I ended up slipping off of the top of the can and I busted the spray can stem off. I busted it down in the can and there was no way to have to the clear flow from the can. After MFing the can, I ordered the 2K clear that OP used off of Amazon.

After letting the base coated handles sit for a couple days, I took the handles out to the car again and finally convinced myself that the color on the handles and the color on the car were definitely not the same and were definitely not going to be the same no matter what I put on top. I didn't want to take any more chances and just took the handles to a body shop and had them sprayed with the right color for $150.

The most difficult part of reassembling the handle assemblies is getting the main spring installed correctly while also sliding the hinge through the handle components and the spring. If you use a little grease on the hinge and take your time, your fingers might not hurt TOO much when you are done.

Removing the handles from the car was pretty easy. I used OPs trick with the painters tape to keep the bolts from falling into the door. (Genius!) I didn't feel like monkeying around with disconnecting the smart key button connections inside the door which made removing and installing the handles a little bit more "tight" but still pretty easy. The hardest part of installing the new handles was reattaching the lock/unlock lever to the locking mechanism. Smaller hands would definitely ease the frustration. I did end up destroying the plastic around one of the knurled nuts when I was taking off the original set of handles from the car for the same reason that happened on the extra set of handles (too much thread lock on the screw).

Even though I had to wait a week longer than I wanted for the finished product and had to pay twice to get them finished, I think the handles ended up looking very nice!

markv · 04-12-2018, 11:21 PM

Quote:

Originally Posted by fork

First I would like to say that this was an excellent DIY write up. I followed it almost to a T.

I had enough foresight before I began this endeavor to buy a set of handles for me to work on as time permitted so that I could leave the handles on the car. That paid off big time for me as what I had hoped would be a straight forward operation took twice as long and cost twice as much as I was expecting.

The disassembly of the extra set of handles was straight forward. The only problem I ran into was that only one of the screws had a liberal amount of thread lock on it and the knurled nut insert ended up splitting the the plastic of the handle before the screw came loose. It was an easy repair for that and I disassembled the handles the same way as the OP. I also used 4-40 screws to replace the rivets on both handles.

I ordered the non-metal spray paint kit from PaintScratch in my car's body color (Deep Blue Pearl). The website even gives the option to put in your car's VIN which would give the correct paint formula for the paint (they say). I sanded the handles, cleaned them, used the supplied degreaser, applied the adhesion promoter and put primer on all as instructed. I put down four coats of the base color and had very good coverage on the handles. But the color just didn't seem to match the car. The spray color was almost like a crayola crayon kind of blue. It was a blue blue that didn't have much of the metallic fleck effect that the paint on the car has. I am a paint newbie and thought the clear would give it deepen the color and give it that sparkle. So I went to spray the clear. The spray kit from PaintScratch comes with a spray gun that you can attach to the top of the spray cans. I had successfully attached the gun to the primer can and the base color can. When I went to attach the spray gun to the clear can and I ended up slipping off of the top of the can and I busted the spray can stem off. I busted it down in the can and there was no way to have to the clear flow from the can. After MFing the can, I ordered the 2K clear that OP used off of Amazon.

After letting the base coated handles sit for a couple days, I took the handles out to the car again and finally convinced myself that the color on the handles and the color on the car were definitely not the same and were definitely not going to be the same no matter what I put on top. I didn't want to take any more chances and just took the handles to a body shop and had them sprayed with the right color for $150.

The most difficult part of reassembling the handle assemblies is getting the main spring installed correctly while also sliding the hinge through the handle components and the spring. If you use a little grease on the hinge and take your time, your fingers might not hurt TOO much when you are done.

Removing the handles from the car was pretty easy. I used OPs trick with the painters tape to keep the bolts from falling into the door. (Genius!) I didn't feel like monkeying around with disconnecting the smart key button connections inside the door which made removing and installing the handles a little bit more "tight" but still pretty easy. The hardest part of installing the new handles was reattaching the lock/unlock lever to the locking mechanism. Smaller hands would definitely ease the frustration. I did end up destroying the plastic around one of the knurled nuts when I was taking off the original set of handles from the car for the same reason that happened on the extra set of handles (too much thread lock on the screw).

Even though I had to wait a week longer than I wanted for the finished product and had to pay twice to get them finished, I think the handles ended up looking very nice!

Looks damn good! Sucks it was such a pain in the ***, but it’s all good now! I just painted mine black, just got the 2k clear to finish them. I’ll post some pics as soon as I get a chance to finish them.

Sent from my iPhone using Tapatalk

OldGuyFla · 10-10-2018, 11:12 AM

Quote:

Originally Posted by fork

First I would like to say that this was an excellent DIY write up. I followed it almost to a T.

I had enough foresight before I began this endeavor to buy a set of handles for me to work on as time permitted so that I could leave the handles on the car. That paid off big time for me as what I had hoped would be a straight forward operation took twice as long and cost twice as much as I was expecting.

The disassembly of the extra set of handles was straight forward. The only problem I ran into was that only one of the screws had a liberal amount of thread lock on it and the knurled nut insert ended up splitting the the plastic of the handle before the screw came loose. It was an easy repair for that and I disassembled the handles the same way as the OP. I also used 4-40 screws to replace the rivets on both handles.

I ordered the non-metal spray paint kit from PaintScratch in my car's body color (Deep Blue Pearl). The website even gives the option to put in your car's VIN which would give the correct paint formula for the paint (they say). I sanded the handles, cleaned them, used the supplied degreaser, applied the adhesion promoter and put primer on all as instructed. I put down four coats of the base color and had very good coverage on the handles. But the color just didn't seem to match the car. The spray color was almost like a crayola crayon kind of blue. It was a blue blue that didn't have much of the metallic fleck effect that the paint on the car has. I am a paint newbie and thought the clear would give it deepen the color and give it that sparkle. So I went to spray the clear. The spray kit from PaintScratch comes with a spray gun that you can attach to the top of the spray cans. I had successfully attached the gun to the primer can and the base color can. When I went to attach the spray gun to the clear can and I ended up slipping off of the top of the can and I busted the spray can stem off. I busted it down in the can and there was no way to have to the clear flow from the can. After MFing the can, I ordered the 2K clear that OP used off of Amazon.

After letting the base coated handles sit for a couple days, I took the handles out to the car again and finally convinced myself that the color on the handles and the color on the car were definitely not the same and were definitely not going to be the same no matter what I put on top. I didn't want to take any more chances and just took the handles to a body shop and had them sprayed with the right color for $150.

The most difficult part of reassembling the handle assemblies is getting the main spring installed correctly while also sliding the hinge through the handle components and the spring. If you use a little grease on the hinge and take your time, your fingers might not hurt TOO much when you are done.

Removing the handles from the car was pretty easy. I used OPs trick with the painters tape to keep the bolts from falling into the door. (Genius!) I didn't feel like monkeying around with disconnecting the smart key button connections inside the door which made removing and installing the handles a little bit more "tight" but still pretty easy. The hardest part of installing the new handles was reattaching the lock/unlock lever to the locking mechanism. Smaller hands would definitely ease the frustration. I did end up destroying the plastic around one of the knurled nuts when I was taking off the original set of handles from the car for the same reason that happened on the extra set of handles (too much thread lock on the screw).

Even though I had to wait a week longer than I wanted for the finished product and had to pay twice to get them finished, I think the handles ended up looking very nice!

Hi fork

I'm sorry that I didn't respond to your post before now.

Glad you found the DIY useful, Sorry to read that the paint match was off. Did you talk to paintscratch about the problem?

The handles look really good, hope it gave you some satisfaction in all that you did.

Dan

OldGuyFla · 10-10-2018, 11:17 AM

Quote:

Originally Posted by markv

Looks damn good! Sucks it was such a pain in the ***, but it’s all good now! I just painted mine black, just got the 2k clear to finish them. I’ll post some pics as soon as I get a chance to finish them.

Sent from my iPhone using Tapatalk

Hi markv

I'm A little late, but where are those pics? Hope everything went O.K. with the project.

Dan

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Paint Matched Door Handles	jtsmith1	Exterior & Interior	52	01-16-2017 10:49 AM
SoCal paint shop for door handles?	dP3NGU1N	Southern California Region	6	01-09-2013 05:18 PM
Paint my door handles in Central Florida?	Osiris	South East Region	0	02-10-2011 09:17 PM
Diy paint door handles	ddvette9	Exterior & Interior	8	11-18-2010 04:46 PM