Should I do the wheel bearings myself or pay a shop?

cossie1600 · 09-14-2013, 09:57 PM

I have a feeling my bearings are going. Should I attack this job or just pay someone to do it? Anyone know the book hours on it? Thanks

Felix 808 · 09-14-2013, 10:46 PM

What are you mech skills? It's not that hard of a job. Just have make sure you install the fronts the right direction & take the ABS sensor out.

I would do it myself, but I also know my skills

YMMV

cossie1600 · 09-15-2013, 12:57 AM

I can do some work, but I have to see if it is worth it for me to get my hands dirty. If it cost me $100, I am not going to waste time doing it

Rusty · 09-15-2013, 08:54 AM

Changing the wheel bearings is easy to do. Here's a link to when I changed my wheel studs. This will give you an idea of what's needed.

Installing ARP wheel studs

roy'sz · 09-15-2013, 09:44 AM

are you running spacers?

takjak2 · 09-15-2013, 10:00 PM

The process is easy, but if they are stuck in there it can be frustrating. I'd DIY

cossie1600 · 09-16-2013, 01:04 AM

Here is the thing that pisses me off. It doesn't appear to be a wheel bearing as I can't rock the wheel. The noise is slowly turning into a bad bicycle chain sound. I still have wheel bearing as number one on my list, but could it be something like a loose exhaust heat shield???

I guess no sears point for me this weekend.

Fishey · 09-16-2013, 09:55 AM

If you can't diagnose a wheel bearing your most likely best off to take it to a shop.

cossie1600 · 09-16-2013, 10:21 AM

Yeah okay, whatever you say.

I reviewed the shop manual, it's actually easy to replace the entire hub. I just need to figure out if the noise is truly the bearing. Now the car is sounding like a bicycle chain when I turn

LostSol · 09-16-2013, 10:51 AM

youre not lowered anything crazy right? just to make sure its not a tire or wheel rubbing.

If not, it could still be your wheel bearing even if you cant rock the wheel, if it lost its grease then it will get loud

osbornsm · 09-16-2013, 11:00 AM

Wheel bearings "should" be an easy DIY, unless of course there's any bit of corrosion. I had to remove my wheel bearings to install the Stillen Brake Cooling ducts. There's only 4 bolts to hold it on... but once removed i couldn't get that hub out with a: hammer, mallet, crowbar, PBR Blaster, jedi force. NOTHING would get that hub out of there.

*I drive the car in the winter so its prolly very corroded in there. Guy at the shop said it 'came right out'" But he had it on a lift, and had a much bigger mallet than i did to "loosen" the hub.

So keep this in mind when doing / replacing a hub.

09-14-2013, 09:57 PM	#1 (permalink)
cossie1600 A True Z Fanatic Join Date: Jun 2009 Location: californee way Posts: 5,380 Drives: 370, Leaf Rep Power: 29	Should I do the wheel bearings myself or pay a shop? I have a feeling my bearings are going. Should I attack this job or just pay someone to do it? Anyone know the book hours on it? Thanks

09-14-2013, 10:46 PM	#2 (permalink)
Felix 808 A True Z Fanatic Join Date: Oct 2011 Location: Camarillo, CA Posts: 1,063 Drives: 2011 PW/Grey T/S 7AT Rep Power: 2806	What are you mech skills? It's not that hard of a job. Just have make sure you install the fronts the right direction & take the ABS sensor out. I would do it myself, but I also know my skills YMMV __________________ Semper Fi Μολὼν λαβέ

09-15-2013, 08:54 AM	#4 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 68 Posts: 34,892 Drives: 2011 Nismo GM 6M Rep Power: 2684436	Changing the wheel bearings is easy to do. Here's a link to when I changed my wheel studs. This will give you an idea of what's needed. Installing ARP wheel studs __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

09-15-2013, 09:44 AM	#5 (permalink)
roy'sz A True Z Fanatic Join Date: Aug 2011 Location: palmdale, ca Posts: 1,299 Drives: 2010 nissan 370z Rep Power: 15	are you running spacers? __________________ https://www.youtube.com/watch?v=RtvG...data_playerARK HFC'S-ARK Grip-Stillen G3-M370-UPREV-Kinetix upper control arm-WC Latheworks-Stage2 Bad@$$ Driver(318whp/268tq)-

09-15-2013, 10:00 PM	#6 (permalink)
takjak2 A True Z Fanatic Join Date: Feb 2011 Location: Sterling, VA Posts: 1,922 Drives: Legit Racecar 370Z Rep Power: 142	The process is easy, but if they are stuck in there it can be frustrating. I'd DIY __________________ Mods \| Stuff \| Things \| Seat Time \| Nismo facebook.com/TeamSparrowSpeed

09-15-2013, 12:57 AM	#3 (permalink)
cossie1600 A True Z Fanatic Join Date: Jun 2009 Location: californee way Posts: 5,380 Drives: 370, Leaf Rep Power: 29	I can do some work, but I have to see if it is worth it for me to get my hands dirty. If it cost me $100, I am not going to waste time doing it

09-16-2013, 01:04 AM	#7 (permalink)
cossie1600 A True Z Fanatic Join Date: Jun 2009 Location: californee way Posts: 5,380 Drives: 370, Leaf Rep Power: 29	Here is the thing that pisses me off. It doesn't appear to be a wheel bearing as I can't rock the wheel. The noise is slowly turning into a bad bicycle chain sound. I still have wheel bearing as number one on my list, but could it be something like a loose exhaust heat shield??? I guess no sears point for me this weekend.

09-16-2013, 09:55 AM	#8 (permalink)
Fishey Base Member Join Date: Sep 2012 Location: Lebanon Posts: 159 Drives: Volvo T5-R Rep Power: 12	If you can't diagnose a wheel bearing your most likely best off to take it to a shop.

09-16-2013, 10:21 AM	#9 (permalink)
cossie1600 A True Z Fanatic Join Date: Jun 2009 Location: californee way Posts: 5,380 Drives: 370, Leaf Rep Power: 29	Yeah okay, whatever you say. I reviewed the shop manual, it's actually easy to replace the entire hub. I just need to figure out if the noise is truly the bearing. Now the car is sounding like a bicycle chain when I turn

09-16-2013, 10:51 AM	#10 (permalink)
LostSol Premium Member Join Date: Jan 2013 Location: Orlando Posts: 1,021 Drives: 2010 370z 40th A.E. Rep Power: 15	youre not lowered anything crazy right? just to make sure its not a tire or wheel rubbing. If not, it could still be your wheel bearing even if you cant rock the wheel, if it lost its grease then it will get loud __________________ 2010 Nissan 370Z 40th Anniversary Edition #762/1000 \| Forgestar \| Michelin \| Swift \| TRS \| Z Speed \| ARK \| Z1 \| Hawk \| CFE \| Evo-R \| GTMat \| Stillen \| Seibon \| Whiteline \| Pioneer \|

09-16-2013, 11:00 AM	#11 (permalink)
osbornsm A True Z Fanatic Join Date: Jun 2011 Location: WHAT Posts: 2,551 Drives: 2018 Camaro SS 1LE Rep Power: 423	Wheel bearings "should" be an easy DIY, unless of course there's any bit of corrosion. I had to remove my wheel bearings to install the Stillen Brake Cooling ducts. There's only 4 bolts to hold it on... but once removed i couldn't get that hub out with a: hammer, mallet, crowbar, PBR Blaster, jedi force. NOTHING would get that hub out of there. I drive the car in the winter so its prolly very corroded in there. Guy at the shop said it 'came right out'" But he had it on a lift, and had a much bigger mallet than i did to "loosen" the hub. So keep this in mind when doing / replacing a hub. __________________ 2018 Camaro SS 1LE* (455hp) - 2011 Nissan 370z (333hp) - 2004 VW R32 (240hp) - 2000 Civic Si (160hp)

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Wheel shop in Vancouver	Bking	Canada	3	04-05-2013 07:53 AM
wheel bearings?	fuct	Brakes & Suspension	10	03-18-2013 09:56 AM
Wheel Bearings	tmjohansen	Other Vehicles	0	04-22-2012 03:16 PM
Wheel damaged by a shop	oleg	Wheels & Tires	19	05-18-2011 09:28 AM