Swift springs review!!!!!

onzedge · 04-25-2012, 02:49 PM

Mr. Zman8 -- if I were you, I would get the camber arms right away. I honsestly do not think there would have been enough adjustment in my stock arms when I installed the Swifts.

kenchan · 04-25-2012, 02:49 PM

Quote:

Originally Posted by ZMan8

My swifts springs are on their way to my house so I hope I can stay in spec. if not than camber arms are next. (o and I'll probably need spacers for the stock rays)

or just sell the wheels to me and you go aftermarket.

btw, are you doing the install yourself?

ZMan8 · 04-25-2012, 02:50 PM

Quote:

Originally Posted by onzedge

Mr. Zman8 -- if I were you, I would get the camber arms right away. I honsestly do not think there would have been enough adjustment in my stock arms when I installed the Swifts.

hmm good advice I will look into prices/brands (I think we have at least 10 vendors on here that sell camber arms)

Alchemy · 04-25-2012, 02:51 PM

Quote:

Originally Posted by ZMan8

My swifts springs are on their way to my house so I hope I can stay in spec. if not than camber arms are next. (o and I'll probably need spacers for the stock rays)

You will love the Swifts ZMan. You will also want spacers. I got my settings to 1.6 front and 2.2 rear without camber arms. I do plan on gettin some myself eventually though.

ZMan8 · 04-25-2012, 02:51 PM

Quote:

Originally Posted by kenchan

or just sell the wheels to me and you go aftermarket.

btw, are you doing the install yourself?

Yes I plan to. Money saved on install labor goes to future mod budget.

ZMan8 · 04-25-2012, 02:52 PM

Quote:

Originally Posted by Alchemy

You will love the Swifts ZMan. You will also want spacers. I got my settings to 1.6 front and 2.2 rear without camber arms. I do plan on gettin some myself eventually though.

Yeah I know, the swifts will make an even more tucked look

.

onzedge · 04-25-2012, 02:54 PM

Quote:

Originally Posted by ZMan8

hmm good advice I will look into prices/brands (I think we have at least 10 vendors on here that sell camber arms)

There are many choices of vendor. I think mine are from concept Z performance and went with the SPC.

Think about it -- it is only about 200 extra dollars, you will already have the car on a a lift and what happens if your stock ones don't cut it?

Anyway... Just food for thought.

kenchan · 04-25-2012, 02:57 PM

Quote:

Originally Posted by ZMan8

Yes I plan to. Money saved on install labor goes to future mod budget.

sounds good. the thing about the rear camber arms is they are hard to get them the right length so it might be better to let a shop that can do alignments install them right then and there for you.

which alignment shop are you planning to take your car to? not some tire place right?

ZMan8 · 04-25-2012, 03:00 PM

Quote:

Originally Posted by onzedge

There are many choices of vendor. I think mine are from concept Z performance and went with the SPC.

Think about it -- it is only about 200 extra dollars, you will already have the car on a a lift and what happens if your stock ones don't cut it?

Anyway... Just food for thought.

Yes from what I have been reading most people get about -2.1 to -2.5 in the rear which is more than I would want. I may have to order a set for the rear then.

Quick noob question, How does the install change (both springs and camber arms) if my car is not on a lift and instead is on jack stands in the garage?

My logic is that for camber arms the suspension system should be preloaded when you set the initial adjustments.

ZMan8 · 04-25-2012, 03:01 PM

Quote:

Originally Posted by kenchan

sounds good. the thing about the rear camber arms is they are hard to get them the right length so it might be better to let a shop that can do alignments install them right then and there for you.

which alignment shop are you planning to take your car to? not some tire place right?

we have a few alignment shops here (one is Touge Factory, which has a very good rep among the drifters around here)

I started doing some research and never finished.

onzedge · 04-25-2012, 03:04 PM

Quote:

Originally Posted by ZMan8

Yes from what I have been reading most people get about -2.1 to -2.5 in the rear which is more than I would want. I may have to order a set for the rear then.

Quick noob question, How does the install change (both springs and camber arms) if my car is not on a lift and instead is on jack stands in the garage?

My logic is that for camber arms the suspension system should be preloaded when you set the initial adjustments.

The install does not care if your car is on jacks or a lift. The lift I used was the kind that allows the wheels to hang. For the intial adjustment, make the new camber arms slightly shorter than the stock arms -- to start. Then get your car to an alignment shop.

kenchan · 04-25-2012, 03:05 PM

Quote:

Originally Posted by ZMan8

we have a few alignment shops here (one is Touge Factory, which has a very good rep among the drifters around here)

I started doing some research and never finished.

ahhh, sounds good. found their site. looks like they do everything.

as for preloading your suspension before torque down, just use your hydraulic under the bottom of your rotor and load it that way. i do that all the time.

make sure you dont raise it up too high though. lol

at the very end put your car on ramps and re check torque after your quick test drive.

ZMan8 · 04-25-2012, 03:08 PM

Quote:

Originally Posted by onzedge

The install does not care if your car is on jacks or a lift. The lift I used was the kind that allows the wheels to hang. For the intial adjustment, make the new camber arms slightly shorter than the stock arms -- to start. Then get your car to an alignment shop.

That's the plan

Quote:

Originally Posted by kenchan

ahhh, sounds good. found their site. looks like they do everything.

as for preloading your suspension before torque down, just use your hydraulic under the bottom of your rotor and load it that way. i do that all the time.
make sure you dont raise it up too high though. lol

at the very end put your car on ramps and re check torque after your quick test drive.

onzedge · 04-25-2012, 03:10 PM

Quote:

Originally Posted by kenchan

ahhh, sounds good. found their site. looks like they do everything.

as for preloading your suspension before torque down, just use your hydraulic under the bottom of your rotor and load it that way. i do that all the time.

make sure you dont raise it up too high though. lol

at the very end put your car on ramps and re check torque after your quick test drive.

NXTAZEE · 04-28-2012, 11:46 AM

I think I'm going to order the swift springs and SPC rear control arms, as it looks like most are needing the arms.

I have a question for those of you who have bolt on spacers; up front, did any of you have issues with the stock studs sticking out through the spacer and touching the wheel? I've read that up to 15mm will touch but 20mm and up doesn't.

04-25-2012, 02:49 PM	#1066 (permalink)
onzedge A True Z Fanatic Join Date: Apr 2010 Location: Battle Lake MN Age: 63 Posts: 183,964 Drives: 370Z 240Z Rep Power: 2684736	Mr. Zman8 -- if I were you, I would get the camber arms right away. I honsestly do not think there would have been enough adjustment in my stock arms when I installed the Swifts. __________________ Koni\|Swift\|Michelin\|Motordyne\|Berk\|RJM Performance\|Gates\|SPL\|Motul\|Technafit\|Ate Super Blue\|Hawk Tommy Kaira\|Momo\|Optima\|Hella\|Hotchkis\|Red Line\|ZSpeed\|Stillen\|B&M\|H&R

04-28-2012, 11:46 AM	#1080 (permalink)
NXTAZEE Track Member Join Date: May 2009 Location: Vancouver Island Posts: 530 Drives: 2010 370Z 7AT Rep Power: 16	I think I'm going to order the swift springs and SPC rear control arms, as it looks like most are needing the arms. I have a question for those of you who have bolt on spacers; up front, did any of you have issues with the stock studs sticking out through the spacer and touching the wheel? I've read that up to 15mm will touch but 20mm and up doesn't. __________________ 2010 Carbon Silver 370Z 7AT charcoal int. sports package \| Clear Bra \| Invidia Gemini CBE \| CF B-Pillars \| CF Fangs \| CF Z emblems \| Swift Springs \| 20mm & 25mm Spacers \| SPC Camber Arms \| Brushed Aluminum shift knob

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Swift Springs-- Nismo Review!!	JJ-NISMO	Brakes & Suspension	39	07-29-2014 07:59 AM
[WTB] Swift Springs	Beastmode	Parts for sale (Private Classifieds)	1	09-13-2011 04:46 PM
BC ERs with Swift Springs and RA Valving REVIEW / (Picture Heavy)	Mozen	Brakes & Suspension	31	05-24-2011 10:46 AM
WTB: Swift or H&R Springs	Mr&Mrs	Wanted	5	04-26-2011 10:51 PM
Swift Springs	Justin1686	North East Region	10	02-24-2011 06:58 PM