ARK GT-S, SPL Camber Arms, Alignment, etc, etc...

jchammond

I'm -0.75* camber all 4 corner's on street & drives great; even tire wear & even handled the "Dragon" @ Zdayz....i would push it to (0*camber) but i'd have the Mexiflush look w/345's on 12's.

__________________
MazWorx built long block | FI-TT-100 Stage 2.75 | IPT built 7A/T

http://www.the370z.com/members-370z-...s-musings.html

jchammond

Unsure if u plan to use spacers to bring wheels out...a 20mm up front & 15mm out back with very little negative camber (below 1*) will look closer to this on the outer edge/ granted that I'm not lowered any.


Sent from my iPhone using Tapatalk

__________________
MazWorx built long block | FI-TT-100 Stage 2.75 | IPT built 7A/T

http://www.the370z.com/members-370z-...s-musings.html

ChopsZ

I don't think I will. When I was running the stock base 18" wheels, I used a set of 20mm Z1 spacers, and from about 55 mph on up, I kept getting a slight vibration. Instead of spacers, maybe I'll have room for wider tires later on down the road.

__________________
She's For Sale! PERFORMANCE: Aero Workz | Akebono | BC Racing | EcuTek | HKS | MaxBore | Motordyne | Nismo | RJM | SPL | StopTech | Z1
AUDIO: Arc Audio | Bazooka | Helix | Pioneer | Stereo Integrity

jchammond

Wherever you get it aligned; when you change camber-it changes toe & as Rusty stated "be sure & have toe a tad on the positive side" (slightly inward) as a 0 setting or -setting will make your pucker factor go up while doing some spirited driving!

__________________
MazWorx built long block | FI-TT-100 Stage 2.75 | IPT built 7A/T

http://www.the370z.com/members-370z-...s-musings.html

ChopsZ

Remember though, I'm on Nismo wheels, not Sport wheels. The offset is a little more aggressive on these.


Yes sir. Honestly, I've never run 0 toe ever on any vehicle for obvious reasons.

__________________
She's For Sale! PERFORMANCE: Aero Workz | Akebono | BC Racing | EcuTek | HKS | MaxBore | Motordyne | Nismo | RJM | SPL | StopTech | Z1
AUDIO: Arc Audio | Bazooka | Helix | Pioneer | Stereo Integrity

Rusty

Sorry I didn't reply to you thread sooner. I spent the weekend hammering on my Power Wagon at Rausch Creek. Went to a Power Wagon get together.

I have the Hotchkis bars. They don't change anything on alignment. But make a difference in handling.

Attached Images

IMG_0898.JPG (216.9 KB, 6 views)

__________________

浪人 - 殺し屋
"The Difficult Anytime, The Impossible By Appointment Only"
http://www.the370z.com/members-370z-...o-journal.html

jchammond

Chop's,
With Nismo wheels; your outer wheel lips are 8.3mm more tucked in on front & just 4mm in on rear/ compared to my wheels pictured.
A 0* camber setting on front is within specs, but would not be within factory oem spec on rear: But would yield great tire wear, as I'm not quite at -1.0 (-0.75 to -0.8 all over)
No spacers needed & you have room for beefier tread.

__________________
MazWorx built long block | FI-TT-100 Stage 2.75 | IPT built 7A/T

http://www.the370z.com/members-370z-...s-musings.html

ChopsZ

I can't think of anyone who does or would run 0* camber.

__________________
She's For Sale! PERFORMANCE: Aero Workz | Akebono | BC Racing | EcuTek | HKS | MaxBore | Motordyne | Nismo | RJM | SPL | StopTech | Z1
AUDIO: Arc Audio | Bazooka | Helix | Pioneer | Stereo Integrity