Opinions on Alginment specs

clintfocus · 10-30-2013, 02:29 PM

Quote:

Originally Posted by Rusty

LMAO!!!!

The Nismo is on stock coilovers for now. That's later. Hotchkis sway bars front and rear. Rear set on softest. Stock ride height. Full SPL parts up front. Control arms, and lower bearings.

So you're saying -2 camber, zero toe, and my caster at -6 would be about right? The rear, I'm not touching. I know how aggressive the camber is back there.

yes for the front that would be good. In the rear set the toe at zero also, ive experimented in the past with slight toe in for high speed sweeper stability, but the rear suspension toe's in under compression as well, so when i tried zero out back it was still fine in the sweepers but had slightly less understeer in the slower corners. Also the factory rear camber setting i think it around -2, if you can get less then that while still getting the correct toe setting, do it.

Rusty · 10-30-2013, 02:36 PM

Forgot about the tires and rims. Fronts are Mich PSS 275/35-19 on a 19x9.5.
The rears are Mich PSS 325/30-19 on 19x12.

I thought you needed a little toe in for the rear, because of snap over steer.

In the spring, I'm planning on doing the whole SPL parts in the rear. So, I'll take care of the rear then.

clintfocus · 10-30-2013, 02:43 PM

Quote:

Originally Posted by Rusty

Forgot about the tires and rims. Fronts are Mich PSS 275/35-19 on a 19x9.5.
The rears are Mich PSS 325/30-19 on 19x12.

I thought you needed a little toe in for the rear, because of snap over steer.

In the spring, I'm planning on doing the whole SPL parts in the rear. So, I'll take care of the rear then.

i noticed you have staggered sizes from your signiture, hence why i havent told you do ditch that rear hotchkis bar yet

lol, day you go square, get rid of that thing!

early in tracking my 370 i played it safe too with the mild toe in, but like i said, dynamically when the rear suspension compresses, it gain's toe in, ive been running on zero rear for a while now and its not by anymeans loose and i run 285 square

Rusty · 10-30-2013, 03:08 PM

Thanks Clint!

10-30-2013, 02:36 PM	#2 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 69 Posts: 35,544 Drives: 2011 Nismo GM 6M Rep Power: 2684439	Forgot about the tires and rims. Fronts are Mich PSS 275/35-19 on a 19x9.5. The rears are Mich PSS 325/30-19 on 19x12. I thought you needed a little toe in for the rear, because of snap over steer. In the spring, I'm planning on doing the whole SPL parts in the rear. So, I'll take care of the rear then. __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

10-30-2013, 03:08 PM	#4 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 69 Posts: 35,544 Drives: 2011 Nismo GM 6M Rep Power: 2684439	Thanks Clint! clintfocus likes this. __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Torque Specs	zero610	Nissan 370Z General Discussions	30	07-09-2016 02:54 PM
2013 specs	Rhino111	Nissan 370Z Owners Manual / Service Manuals	3	05-11-2013 01:54 AM
What might be the specs to this car	Good_Tymes	Exterior & Interior	6	04-04-2013 07:15 PM
My Alignment specs - Please Help	FlawlessZ	Brakes & Suspension	39	01-04-2013 10:35 AM
Specs of the 3.7L VQ37VHR	admin	Engine & Drivetrain	17	11-12-2012 04:18 PM