Nissan 370Z Forum  

Who's making the move to STU?

Originally Posted by Zewerr Good luck, man. I was planning on popping a front wheel off tomorrow and throwing one of my new 315s under there with a rather cheap

Go Back   Nissan 370Z Forum > Nissan 370Z Tech Area > Track / Autocross / Drifting / Dragstrip


Like Tree258Likes

Reply
 
LinkBack Thread Tools Display Modes
Old 02-23-2021, 05:08 PM   #301 (permalink)
Base Member
 
ConekillerZ34's Avatar
 
Join Date: Jan 2020
Location: DC
Posts: 26
Drives: 2016 370Z Nismo Tech
Rep Power: 9
ConekillerZ34 has a reputation beyond reputeConekillerZ34 has a reputation beyond reputeConekillerZ34 has a reputation beyond reputeConekillerZ34 has a reputation beyond reputeConekillerZ34 has a reputation beyond reputeConekillerZ34 has a reputation beyond reputeConekillerZ34 has a reputation beyond reputeConekillerZ34 has a reputation beyond reputeConekillerZ34 has a reputation beyond reputeConekillerZ34 has a reputation beyond reputeConekillerZ34 has a reputation beyond repute
Default

Quote:
Originally Posted by Zewerr View Post
Good luck, man. I was planning on popping a front wheel off tomorrow and throwing one of my new 315s under there with a rather cheap *** fitment jig I borrowed. I'm hoping it'll at least get me close.

I didn't take the time to set up a jig or anything, but I actually created a rough mold of the negative space by making some putty in the kitchen and then jamming it between the wheel and arm. I found I had 21-23mm of space depending on whether I measured at the edge of the wheel lip or at the edge of the tire. The space for the tire gets easier as you go up.

So I went ahead and ordered Forgestars with a +22 offset, which will put me 0.65mm inset of my current setup on the outer edge, and 13.35mm inset on the inner edge. That's the wheel of course, and the 315 tire will be a bit puffier so I'm hoping it doesn't take up more than 7mm of the space inside. I can use a 2.5 or 5mm spacer from Z1 to fix that right up if it does, and I'll use a 5 or 10mm spacer in the rear anyway. Will obviously update everyone with they arrive in hopefully 2mo or less...

TL;DR: YOLO hope these things fit
__________________
2016 Nismo 370Z | SCCA STU Autocross Build WIP
2015 GT-R Black Edition | Sold
2006 350Z SCCA STU prepped | Sold
ConekillerZ34 is offline   Reply With Quote
Old 02-24-2021, 01:49 AM   #302 (permalink)
Base Member
 
Zewerr's Avatar
 
Join Date: Jan 2019
Location: Tacoma, WA
Posts: 45
Drives: 11 370Z 82/182 STU
Rep Power: 6
Zewerr is on a distinguished road
Default

I couldn't trust the measuring I did on Sunday. I do have access to a legit professional fitment tool. But I would need to drive to Portland to get it which is a 4 hour round trip. I may consider it this weekend.
Hotrodz likes this.
Zewerr is offline   Reply With Quote
Old 02-27-2021, 06:25 PM   #303 (permalink)
Base Member
 
Zewerr's Avatar
 
Join Date: Jan 2019
Location: Tacoma, WA
Posts: 45
Drives: 11 370Z 82/182 STU
Rep Power: 6
Zewerr is on a distinguished road
Default

Quote:
Originally Posted by ConekillerZ34 View Post
So I went ahead and ordered Forgestars with a +22 offset,
I think you might be in the sweet spot with the +22. I got hold of the fitment tool and set it to +25 and it appears the tire would be rubbing against the spindle just a little. +22 seems to give it a mm or two of clearance. The tool still probably isn't perfect, but it seems to give me a good idea. Now, should I take the plunge and pull the trigger on some wheels, trusting my results?

Zewerr is offline   Reply With Quote
Old 02-28-2021, 05:03 PM   #304 (permalink)
Track Member
 
Join Date: Apr 2013
Location: Colorado
Posts: 623
Drives: Poor man's Porsche
Rep Power: 541
Brendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond repute
Default

Do it
Brendan is offline   Reply With Quote
Old 03-03-2021, 07:50 PM   #305 (permalink)
Track Member
 
Join Date: Apr 2013
Location: Colorado
Posts: 623
Drives: Poor man's Porsche
Rep Power: 541
Brendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond repute
Default

I was wrong about the fender rule. It doesn't say anywhere that you have to fit the tire under the fender. That should open up some options for 18x11. I mounted 315 on my current wheels today pretty easily. No rubbing and due to the shorter height, a little bit better clearance. I'll take some pics this weekend if I can get the prep on the car done in time

Here's some of the tires mounted
315 on 18x10.5
https://photos.app.goo.gl/QU9b3DN8rLGgWyox7
Rusty, Hotrodz and Tedmeister like this.

Last edited by Brendan; 03-03-2021 at 07:57 PM.
Brendan is offline   Reply With Quote
Old 03-06-2021, 07:02 PM   #306 (permalink)
Track Member
 
Join Date: Apr 2013
Location: Colorado
Posts: 623
Drives: Poor man's Porsche
Rep Power: 541
Brendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond repute
Default

Finally got it to rub. I'm currently at -3 degrees of camber and my height is at 26.5 inches. I think I can raise the car another half inch and make it work. The rub happened going over a pretty huge dip in the road at speed and the witness marks are pretty minimal, so I'm hoping a little extra height will get me there.
Brendan is offline   Reply With Quote
Old 03-06-2021, 10:33 PM   #307 (permalink)
Base Member
 
Zewerr's Avatar
 
Join Date: Jan 2019
Location: Tacoma, WA
Posts: 45
Drives: 11 370Z 82/182 STU
Rep Power: 6
Zewerr is on a distinguished road
Default

Can we get some picts of them mounted on the car?
Zewerr is offline   Reply With Quote
Old 03-07-2021, 08:25 AM   #308 (permalink)
Track Member
 
Join Date: Apr 2013
Location: Colorado
Posts: 623
Drives: Poor man's Porsche
Rep Power: 541
Brendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond repute
Default

Quick album before I get to work on it

https://photos.app.goo.gl/buEqgziPE6cdQgfT9
gomer_110 and Hotrodz like this.
Brendan is offline   Reply With Quote
Old 03-07-2021, 12:09 PM   #309 (permalink)
Base Member
 
ConekillerZ34's Avatar
 
Join Date: Jan 2020
Location: DC
Posts: 26
Drives: 2016 370Z Nismo Tech
Rep Power: 9
ConekillerZ34 has a reputation beyond reputeConekillerZ34 has a reputation beyond reputeConekillerZ34 has a reputation beyond reputeConekillerZ34 has a reputation beyond reputeConekillerZ34 has a reputation beyond reputeConekillerZ34 has a reputation beyond reputeConekillerZ34 has a reputation beyond reputeConekillerZ34 has a reputation beyond reputeConekillerZ34 has a reputation beyond reputeConekillerZ34 has a reputation beyond reputeConekillerZ34 has a reputation beyond repute
Default

Quote:
Originally Posted by Zewerr View Post
I think you might be in the sweet spot with the +22. I got hold of the fitment tool and set it to +25 and it appears the tire would be rubbing against the spindle just a little. +22 seems to give it a mm or two of clearance. The tool still probably isn't perfect, but it seems to give me a good idea. Now, should I take the plunge and pull the trigger on some wheels, trusting my results?
Go for it! I thought the same thing based on measurements. My calculations suggested +24 would work, but with some uncertainty on the widest part of the tire -- so I figured if I'm going to potentially need spacers either way, I started at 22. I also have the Nismo flares so that helps (though only visually) with any poke.
__________________
2016 Nismo 370Z | SCCA STU Autocross Build WIP
2015 GT-R Black Edition | Sold
2006 350Z SCCA STU prepped | Sold
ConekillerZ34 is offline   Reply With Quote
Old 03-08-2021, 11:35 AM   #310 (permalink)
Track Member
 
Join Date: Apr 2013
Location: Colorado
Posts: 623
Drives: Poor man's Porsche
Rep Power: 541
Brendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond repute
Default

I think I got it sorted. I'll get some proper photos later today. I will be interested to see what other folks 315 journey looks like. I'll miss the lower stance.
Brendan is offline   Reply With Quote
Old 03-08-2021, 09:17 PM   #311 (permalink)
Track Member
 
Join Date: Apr 2013
Location: Colorado
Posts: 623
Drives: Poor man's Porsche
Rep Power: 541
Brendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond repute
Default

Issa monster truck now

_BES6507 by brendan sobers, on Flickr

_BES6502 by brendan sobers, on Flickr

_BES6498 by brendan sobers, on Flickr

_BES6490 by brendan sobers, on Flickr
gomer_110, Hotrodz, Zewerr and 2 others like this.
Brendan is offline   Reply With Quote
Old 03-11-2021, 05:01 PM   #312 (permalink)
Track Member
 
Join Date: Apr 2013
Location: Colorado
Posts: 623
Drives: Poor man's Porsche
Rep Power: 541
Brendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond repute
Default

I'm also back on my project to get a set of non-shitty-to-work-with and legal fuca for the z. I picked up these arms from gk-tech. The plan will be to buy some rod ends to replace the sphericals on the inboard side of the upper control arm. My first thought would be to replace them with the rod ends from the z1 arms which are actually pretty nice. Unfortunately the z1 rod ends appear to be rh thread and the gk-tech need a lh thread. So where I am is I will need a lh thread 3/4 16 rod end with a non metallic cylinder bushing. There seem to be a few off the shelf options available at speedway motors and summit racing but I am open to other sources and input from anyone with fabrication experience.
Rusty and Hotrodz like this.

Last edited by Brendan; 03-11-2021 at 05:04 PM.
Brendan is offline   Reply With Quote
Old 03-13-2021, 06:37 AM   #313 (permalink)
A True Z Fanatic
 
gomer_110's Avatar
 
Join Date: Aug 2011
Location: Perrysburg, OH
Posts: 17,992
Drives: '11 Nismo #528 GM
Rep Power: 36940
gomer_110 has a reputation beyond reputegomer_110 has a reputation beyond reputegomer_110 has a reputation beyond reputegomer_110 has a reputation beyond reputegomer_110 has a reputation beyond reputegomer_110 has a reputation beyond reputegomer_110 has a reputation beyond reputegomer_110 has a reputation beyond reputegomer_110 has a reputation beyond reputegomer_110 has a reputation beyond reputegomer_110 has a reputation beyond repute
Default

Quote:
Originally Posted by Brendan View Post
I'm also back on my project to get a set of non-shitty-to-work-with and legal fuca for the z. I picked up these arms from gk-tech. The plan will be to buy some rod ends to replace the sphericals on the inboard side of the upper control arm. My first thought would be to replace them with the rod ends from the z1 arms which are actually pretty nice. Unfortunately the z1 rod ends appear to be rh thread and the gk-tech need a lh thread. So where I am is I will need a lh thread 3/4 16 rod end with a non metallic cylinder bushing. There seem to be a few off the shelf options available at speedway motors and summit racing but I am open to other sources and input from anyone with fabrication experience.
Before they allowed sphericals in SP I went through the same thing for the rear arms. I just got the rod ends from Speedway and they've worked fine ever since. I did need tp have a local machine shop make me a few sleeves and spacers though to match the OE dimensions though.
__________________
'11 370Z Nismo #528 Fast Intentions | Stillen | Motordyne | Uprev | CSF | Zspeed | Z1 Motorsports | AST | Swift | SPC | SPL | Whiteline | Hotchkis | Bride | Schroth | Robispec | Cusco | Nismo | Volk | Forgestar | Hoosier | RJM
'17 Titan Bone Stock

Last edited by gomer_110; 03-13-2021 at 07:14 AM.
gomer_110 is offline   Reply With Quote
Old 03-13-2021, 07:10 AM   #314 (permalink)
Track Member
 
Join Date: Apr 2013
Location: Colorado
Posts: 623
Drives: Poor man's Porsche
Rep Power: 541
Brendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond reputeBrendan has a reputation beyond repute
Default

Quote:
Originally Posted by gomer_110 View Post
Before for they allowed sphericals in SP I went through the same thing for the rear arms. I just got the rod ends from Speedway and they've worked fine ever since. I did need tp have a local machine shop make me a few sleeves and spacers though to match the OE dimensions though.
Hell yea. You inspired me to try this. So far this is my most promising lead

https://www.barnes4wd.com/Forged-Chr...ads_p_888.html

So not only will it have 4x4 ride height but actual 4x4 parts.
Can't wait to trigger stance bois.
gomer_110, Rusty and Hotrodz like this.
Brendan is offline   Reply With Quote
Old 03-14-2021, 05:57 PM   #315 (permalink)
Base Member
 
Zewerr's Avatar
 
Join Date: Jan 2019
Location: Tacoma, WA
Posts: 45
Drives: 11 370Z 82/182 STU
Rep Power: 6
Zewerr is on a distinguished road
Default

So, I ordered some 18x11 +24 custom made Forgestars. I'm thinking +24 might be a tolerable rub. If not, I'll add some small spacers. We'll find out in 5-6 weeks. I'm hoping to have everything squared away in time for Crow's CT.
Hotrodz, Brendan and SITOZ like this.
Zewerr is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Making a Big Move. Tim.c Nissan 370Z General Discussions 18 08-05-2015 06:07 AM
maybe a stupid move? dhkim5599 Nissan 370Z General Discussions 28 05-23-2011 09:56 PM
Move your car !!! John Bradley Nissan 370Z General Discussions 30 10-31-2010 11:25 PM
Your Most Ridiculous OCD Move OldGuy Nissan 370Z General Discussions 45 03-06-2010 05:28 PM


All times are GMT -5. The time now is 05:24 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 PL2