Car wont start.

VCuomo · 03-06-2013, 01:09 PM

Quote:

Originally Posted by Garrett63

Gah dammit im trying to pull the damn fuse today and I cant get the fuse box out. I removed all the necessary parts to make room for it to come out but after I unlock the 2 clips on the fuse box to pull it out its snagged. It feels like wires are attached to the bottom of the box that are short holding it down. Am I missing a clip on the fuse box itself?

That's what it felt like when I tried pulling the box out from my Z. Just pull the box up and when it feels like it's snagging, pull up harder and it should free up and pull out. And, of course, make sure that the clips are fully disengaged.

R0bDC · 03-06-2013, 01:45 PM

I really wished I would've beat the crap out of the box, I just tap it a few times.

forza370z · 03-06-2013, 01:59 PM

Here is a video on youtube might help little bit.

As in the pix, I just pull out the fuse box and there are two tabs at the bottom of the fusebox. Push the tabs down and hold them then try to open the box. You don't have to open the box completely to pull the fuse. Just open it slightly like I did shown in the pix. Good luck.

Garrett63 · 03-06-2013, 02:00 PM

Victory! go eff yourself pinkish red fuse from hell! Yeah I just got over my pussitis and pulled the fuse box out a little harder and there she blew.

forza370z · 03-06-2013, 02:04 PM

Quote:

Originally Posted by Garrett63

Victory! go eff yourself pinkish red fuse from hell! Yeah I just got over my pussitis and pulled the fuse box out a little harder and there she blew.

SouthArk370Z · 03-06-2013, 02:59 PM

Quote:

Originally Posted by Garrett63

Gah dammit im trying to pull the damn fuse today and I cant get the fuse box out. I removed all the necessary parts to make room for it to come out but after I unlock the 2 clips on the fuse box to pull it out its snagged. It feels like wires are attached to the bottom of the box that are short holding it down. Am I missing a clip on the fuse box itself?

The big harness/cable that enters the bottom of the IPDM is probably hanging up. I was able to reach around the IPDM (toward the passenger compartment) and guide the harness around a corner, but I'm a small guy. If you can't get your arm in there, a wood dowel or other soft material should work.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
car wont start after attempting to program ecu with hypertech	Thorazine_IM	Tuning	49	06-18-2013 03:51 AM
car wont start ipd steering lock	maciaqua	Nissan 370Z General Discussions	35	03-18-2013 02:50 AM
370z wont start no power . Where to start	acracing118	Exterior & Interior	6	01-05-2013 06:37 PM
Car wont start, fuel pump 400?!	A 2 Z	Nissan 370Z Warranty / Scheduled Maintenance / Servicing / Repairs	4	09-05-2012 03:07 PM
Car wont start	faijia	Nissan 370Z General Discussions	4	06-14-2009 11:37 PM

03-06-2013, 01:45 PM	#32 (permalink)
R0bDC Enthusiast Member Join Date: Nov 2012 Location: California Posts: 307 Drives: 2009 370Z Rep Power: 12	I really wished I would've beat the crap out of the box, I just tap it a few times.

03-06-2013, 01:59 PM	#33 (permalink)
forza370z A True Z Fanatic Join Date: Oct 2011 Location: 403 Forbidden Posts: 2,512 Drives: 2009 NISMO 370Z Rep Power: 18	Here is a video on youtube might help little bit. As in the pix, I just pull out the fuse box and there are two tabs at the bottom of the fusebox. Push the tabs down and hold them then try to open the box. You don't have to open the box completely to pull the fuse. Just open it slightly like I did shown in the pix. Good luck.