A little nippy this morning...

MZ DAIZY · 11-15-2019, 06:48 AM

Quote:

Originally Posted by vtec to vvel

When you said it revved up slowly, are you referring to the initial system self-check where the all the needles on the gauge clusters go to the other side? Or are you talking about when driving but feels like limp mode?

If the latter, I get this from time to time is bc my MAF sensors are dirty (OBD II sensor pulled MAF code), and turn off for 30 seconds and restart and runs like a beast again.

This was after the “sweep” Car was running and just kept revving. Car was screaming! I was getting ready to push the off button when it hit redline and quickly dropped to idle.

Would a dirty MAF throw a CEL? No light and starting/running normally. Just don’t want to go through that again!

SouthArk370Z · 11-15-2019, 08:23 AM

Quote:

Originally Posted by MZ DAIZY

... Would a dirty MAF throw a CEL? No light and starting/running normally. Just don’t want to go through that again!

Not always. The first thing I'd do is check for any DTCs that may have been thrown.

Cleaning the MAFs is very easy - two screws and the MAF slides right out, spray it down with cleaner, let dry, re-install, do the other side. Takes less than 5 minutes per side. Considering all the problems MAFs can cause and how easy they are to clean, you might want to clean them once a year - or every oil change if you're real finicky (but that's probably overkill).

vtec to vvel · 11-15-2019, 11:08 PM

Quote:

Originally Posted by MZ DAIZY

This was after the “sweep” Car was running and just kept revving. Car was screaming! I was getting ready to push the off button when it hit redline and quickly dropped to idle.

Would a dirty MAF throw a CEL? No light and starting/running normally. Just don’t want to go through that again!

A dirty MAF will not always throw a CEL. My CEL comes in every few months and the obd scanner throws a MAF code, which I’ll clear out.

And I assume you didn’t have your foot on the gas pedal when it was redlining? lol I have to ask

MZ DAIZY · 11-16-2019, 05:21 AM

Quote:

Originally Posted by vtec to vvel

A dirty MAF will not always throw a CEL. My CEL comes in every few months and the obd scanner throws a MAF code, which I’ll clear out.

And I assume you didn’t have your foot on the gas pedal when it was redlining? lol I have to ask

No foot on the gas. LOL.

BettyZ · 11-16-2019, 11:24 AM

Quote:

Originally Posted by MZ DAIZY

No foot on the gas. LOL.

I'd clean the MAFs and see if it repeats itself. They're easy to access.

Sent from my SM-G955U using Tapatalk

vtec to vvel · 11-16-2019, 07:33 PM

Quote:

Originally Posted by BettyZ

I'd clean the MAFs and see if it repeats itself. They're easy to access.

Sent from my SM-G955U using Tapatalk

Just be really careful when cleaning them. There is a thin film layer you don’t want to ruin.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Saw this car this morning. WTF?	cooltoy	The Lounge (Off Topic)	10	06-15-2019 09:23 AM
VDC Always off in morning?	ssphotography	Engine & Drivetrain	19	05-08-2014 10:04 PM
So I did this to my Z this morning :-(	bbowers825	Nissan 370Z General Discussions	17	03-02-2013 10:50 AM
ACH on the morning of the 4th	Ackrite	Southern California Region	0	07-04-2012 03:58 AM
Fun morning at AAM	ak6ar	Mid-Atlantic Region	32	03-24-2012 12:55 AM