![]() |
Quote:
|
Doing a HP/$ cost-benefit analysis for more N/A gains. Looks like swapping out my Berk HFCs for F.I. resonated pr non-res test pipes is the best bet.
Sent from my SM-G955U using Tapatalk |
Test fit.
https://uploads.tapatalk-cdn.com/202...2bcb54aaa2.jpg Sent from my SM-G955U using Tapatalk |
Quote:
:tup: |
Quote:
|
Quote:
|
Quote:
|
Quote:
Sent from my SM-G975U using Tapatalk |
Square bit for what? Only holes I remember having to open up a bit for a tight fit was on front side for latch and bumpers and drill out small holes if you want to use windshield washer line/nozzles.
|
Quote:
|
Quote:
|
Quote:
How good is the fitment overall? |
Quote:
|
Quote:
The azzrags at Seibon "guarantee" that there will be less than .5" of gap - on both sides. https://uploads.tapatalk-cdn.com/202...472b8e3c07.jpg Sent from my SM-G955U using Tapatalk |
:thumbsdown: :(
|
Quote:
|
Quote:
|
Quote:
Quote:
|
2 Attachment(s)
I just installed a Ctek indicator panel in the front bumper. This now allows for easy hookup without opening the hood and gives my battery status.
Attachment 142086 Sent from my iPhone using Tapatalk |
^^ I've thought about doing something similar since my car is becoming a garage queen... be nice to just plug the battery tender in and walk away.
|
Had a single rear rim stolen weekend before last so am now waiting on a tire to put on the replacement rim i already ordered and had shipped to me
|
Quote:
|
|
Finally -- I washed the 370 after she sat for 2 months in the garage:
Before: http://scontent.fsac1-2.fna.fbcdn.ne...6f&oe=5ECC6D31 After: http://scontent.fsac1-1.fna.fbcdn.ne...2c&oe=5ECC2430 |
1 Attachment(s)
Also washed my car today and topped with bead maker. That stuff looks great on top of a ceramic coating.http://www.the370z.com/attachment.ph...1&d=1587937925
|
Quote:
|
|
Quote:
This was my first time using it and I think it looks great. I have heard it takes a way a little bit of beading properties compared to just straight ceramic coating but I'll have to test that out. |
New toy showed up. Raceseng Cylix.
https://i.imgur.com/55yzZE6l.jpg https://i.imgur.com/wlbrLpHl.jpg |
2 Attachment(s)
Yaw sensor bypass switch off and on.
|
Quote:
Sent from my SM-G975U using Tapatalk |
Quote:
|
Quote:
|
Found it and ordered. Thanks fellas!
Sent from my SM-G975U using Tapatalk |
Quote:
|
1 Attachment(s)
Fluids! Diff, MT, Brake, Steering...
|
ZSpec's Ultimate Fastener Kit arrived today. Only two of the 42 provided front timing chain case/intake valve timing control cover fasteners are long enough to actually fasten anything. Not entirely pleased by this development. Shot ZSpec an email and will let you all know the response.
|
FRS - faulty line bad press fitting CJM
2 Attachment(s)
4/29 - I had a rough day! I started at 10:00 am and got everything installed on the CJM s1.SE FRS. I pressurized the system. The pump gave me a sign. All is good! I crank the engine about 2 seconds or more. the engine roars to life! Yay! I did it!
I see gas shooting from the engine bay. I quick cut the engine and observe the issue. I have a faulty bad pressed line from the regulator to the fuel rail. Tomorrow I will reach out to customer support and make them aware of my issue. I will also go to a shop to see if they can fabricate me a new line or somehow salvage the current one. BAD LUCK is how I will mark this one down. It happens. Other than that install was a breeze. However, lack of instructions online. I couldn't seem to find much. The install PDF from CZP where I bought it focused primarily on the fuel pump and how to fabricate it to adjust for larger pumps. PIA. 4/30 - replaced the bad line.. now with my fuel pressure at 55lbs and even trying to lower it to 50 and 45 the vehicle won’t turn over or stay running at idle.. I do believe my stock ecu mapping can’t handle the new injectors 1050cc and new pump 450 walboro. Is that the issue? spoke to specialty...I need to get towed to the shop. Stock ECU map won’t run my installed parts! May 1 - tune date set 9 am!!! Wish me the luck! 5/1 - tune day 5/3 - I went to start the vehicle today after filling up the first time with E85. It took a bit longer than usual to turn over. At times during the drive to the store...I felt a bit of hesitation in throttle response.. I just installed new injectors and fuel pump . At tune on 5/1 seemed to run really strong seemed a bit out of breathe today. Maybe it’s just me. I dunno |
Finishing up on the ZSpec dress up kit.
https://uploads.tapatalk-cdn.com/202...09d645a509.jpg Sent from my SM-G955U using Tapatalk |
Looks great!
Quote:
|
All times are GMT -5. The time now is 01:40 PM. |
Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 PL2