Looks like maybe those two black screws hold the HID casing in place which would give E/W what he needs.

Or this?

http://i50.tinypic.com/9tmio1.jpg

Yeah that's the thing he wants. His snapped in half.

Sucks though because it means E/W is gonna have to crack his headlights again. Feelin' lucky?

he can have it!

wait? what do you mean crack his headlights again?

I think the troll is that we're going to convince him to crack his headlights open again and they're going to melt into goo.

If it's just to install that clip for the HID bulb he can get it in through the headlight bulb cover. He will need a small angle wrench with a phillips to loosen and tighten up

Yeah that's precisely the part he needs. Oh right you can just go through the back of the housing to get at the bulbs. He should be good to go.

wait up, let me load up a video to remove and install that clip for ya'll

I don't think he'll need it. We figured out the jenga puzzle/ballast last time around.

I'd actually like to take the whole piece, it looks like the two screws hold it in place. I dont think the "U" hook metal piece is what I need, I need the actual piece that retains the "U" hook.

Thats exactly it.

Alright, cool. If he do need the clip he really can have it.

Which side do you need?

Yeah, it looks pretty easy to swap out, without having to open the headlight, remember to get to this area, you take off the plastic cover in the back, turning it counter clockwise. Really simple.

I believe its the drivers side.

with the ballast ATTACHED haha

Awww, sucks cuz I have the passenger side.

You do need to open up the housing in order to swap that part because it's part of the projector.

Wait up, let me take a few pic's for you to see!

http://i50.tinypic.com/15a611.jpg
http://i48.tinypic.com/a3ihoy.jpg

hmmmm, Im not sure about that, looking at the picture, it doesnt look like that.

Wouldnt the passenger and the drivers side be the same, I would think so.

Negative, the studs holding onto the projector bracket has L and R orientation.

http://i48.tinypic.com/29bd08k.jpg
http://i49.tinypic.com/15yu6iw.jpg

Ahhhhh... so do you think its gonna be a pain in the azz to do?

Look at this pic, you notice where the "U" hook is snapped under the metal housing, it holds the light in place, that little tab (theres 2, one for each side of the "U" hook.) That tab snapped off, thats what Im trying to replace.

This???

http://i49.tinypic.com/2070ojk.jpg

Oh hey I thought it was the HID bulb clip.

Nevermind! I know what you're talking about now.

Look at the top of the picture, under the the words, "Originally Posted by weiboy718"
under your name, about an inch down, you see that metal lip.. thats the piece that snapped off..

http://i46.tinypic.com/a307ko.jpg

the part that is circle right!

Thats it! I wasnt sure how to do what you did, myself!

Yeah, that is part of the projector. You will need to replace the whole thing. Confirm which side for sure, I have no use for it and I can give it to your for free.

All's well etc

projector removed

http://i46.tinypic.com/e7ku50.jpg
http://i49.tinypic.com/2h2l4kn.jpg

Ahh dude that would be badass.. Im on vacation right now, I wont be back in DC until the 21st. I'll let you know as soon as I know.

Damn dude, its an entire piece, fuuuuuuck. :facepalm::facepalm::facepalm:

It's not too bad as long as you have the part.

So im guessing to get this piece out, I will have to completely disassemble the headlight, no way around it.

yes unfortunately! after disassemble you'll need to unscrew both adjustment bolt and a clip to remove the projector. shouldn't be hard though.

yeah to get the entire projector out, you'll have to...bake it again.

fvck! :facepalm:

step right up!

spin the wheel!

take yo chances...