Z&I

Hi NYC Z34 ...
Happy to try to help ...
Here's my email address:
bobgallagherfoto@aol.com
Much easier to communicate that way.
I will have a copy your message waiting to answer you.
It is much easier to correspond that way.
Read all 101 pages ??? wow ;-)
The thread was started by TopGunZ ... and he was able to successfully get his project done, but he has engineering and manufacturing experience under his belt.
Just a few things to send in your email:
Miles on the car - miles on the Stillen kit
History of the Stillen install and maintenance including check for Boost leaks
Stock motor ? Stock Stillen Tune ? Dyno ?
The stock Stillen set up with their canned UpRev tune generally produces about 415 whp provided the installation was done correctly.
Can't really recommend any shops for you - everyone is an expert until they run in to problems...found that out the hard way.
You can try to contact Stillen to see if they have any authorized or recommended shops in our area.
Looking forward to hear from you...
Bob

Hey Z&I,
I just joined the Z club and wanted reach out to you regarding performance shop question, i just finished reading all 101 pages of Jwllis saga on his car and you seemed to be a knowledgeable person, i am in the Rockland NY area and was wondering if you could point me in a good direction with a performance shop in NJ? i have an 09 Z with a Stillen SC, Stillen Headers and Berk test pipes. Bought the car from a dealer like this, so i wanna Dyno and see what going on with the car. It runs now, the prosport air/fuel gauge is making a alarm sound when i get on it, everything seems fine to me though, but i am a newbie. Any help will help. THX

Hey! Sorry I don't get notifications from your wall lol..I'm 5 min from the GWB as well...we'll start doing some once its starts getting warmer out...this is the thread where we organize http://www.the370z.com/north-east-re...thread-85.html

Where and When ?
I'm only a few miles from the GW Bridge
Bob

Hey u see ur from jersey too, u should check out the north jersey meet thread

http://images.tapatalk-cdn.com/15/10/06/2054da745552ccd6a8a6b6355bd1716f.jpg Sent from my iPhone using Tapatalk

Basically you need to get the lightest psi spring they offer. It is the blue one. Then you need to trim it down to XX length. Ill have to measure mine but I cut off about a half inch or so. I took...

Jwillis, That thing looks awesome! Cant wait to see the final product. Mine is working out great! My intake temps are amazing. I was planning on making a video to show them at idle and then on a hard...

Sounds about like performance shops :rofl2:

Your life is dependent on 3-4 things in your car. Tires, wheels, brakes, airbags. Don't cheap out on any of them.

With the new 6 puck clutch and flywheel, launch control and traction control...I can't tell you how much of a difference there is from a stop. I haven't tried the flat foot shifting yet, I'm a little...

The operation of setting the traction control is as simple as toggling the cruise control lever up and down. That is the beauty of EcuTeK, it is simple to use. The money you spend on this will be...

The Map sensor conversion has been figured out! Using our factory MAP sensor on the intake manifold. This is what I've done - Wire #3 SB - MAF signal. This wire needs to be removed on both...

Sorry, I did not take any. Ill make one of my next trip after I put on the new 3.4" js pulley....when she breaks 500 ;)

http://s.quickmeme.com/img/57/571d3c3d3390d0201772e1b7f9c5f09ab7053ce6aa6dbe815a0af88b824533fb.jpg

Well. The 500 Mark has yet to be hit. I made 490whp and 390tq. This was at 5500ft elevation. Up here I only got 10psi out of the blower. At sea level I would have see 13psi and would have been close...

Just got it running great! Took it all off and put it back on. Not sure what it was but I'm ready to dyno tomorrow!! Stay tuned....

Hey TopgunZ I wish You the best :tup: I feel for you! It sometimes takes a little longer ....:stirthepot: I could tell you my story! But that would take far too long................ Keep up...

Yes I am. Heres some almost finished pics.

New number with ecutek 677.81whp 581.60 tq at 14.91 psi on e85. Stock motor. http://images.tapatalk-cdn.com/15/08/20/86fb183d484b2d0cc62c892adc41dc10.jpg