FL 4MotionA True Z Fanatic |
Last Activity: 02-05-2024 11:19 PM
- User Lists
Likes Given
11150 Likes
-
FL 4Motion liked post by old guy On thread : The new “what did you do to your Z today” (with off topic replies) XXXVIIIAnd people want government run health care ! WAKE UP AMERICALiked On: 12-06-2020, 07:17 PM
Posted On: 12-05-2020, 11:27 PMFL 4Motion liked post by BettyZ On thread : The new “what did you do to your Z today” (with off topic replies) XXXVIIIThere's just so much fvuckedupedness here I can't even summarize it. But I'll try. Basically, the vaccination panel appointed by the gov't thinks nursing home residents and older folks are better off...Liked On: 12-06-2020, 07:17 PM
Posted On: 12-05-2020, 10:52 PMFL 4Motion liked post by SouthArk370Z On thread : The new “what did you do to your Z today” (with off topic replies) XXXVIIIA big blob of silicone should keep things quiet until you can remove the clamp.Liked On: 12-06-2020, 07:16 PM
Posted On: 12-05-2020, 10:35 PMFL 4Motion liked post by JARblue On thread : Autonomous Driving:iagree: Sounds like a good time to be had by all :icon17:Liked On: 12-06-2020, 07:06 PM
Posted On: 12-06-2020, 07:01 PMFL 4Motion liked post by ZoomZ On thread : Adding more than max oil levelRule of thumb: OIL QUANTITY will not fix oil TEMP. or Oil Pressure problems! (ok unless, you run so low that you aint picking the dam oil up-then it's your fault. LOL) (or if you put too much...Liked On: 12-06-2020, 07:02 PM
Posted On: 12-06-2020, 12:38 PMFL 4Motion liked post by Spooler On thread : Adding more than max oil levelHas he checked/replaced his galley gaskets on the front cover. This will cause him to loose the engine if he keeps driving it like this. If the engine was just built, he's got problems with...Liked On: 12-06-2020, 07:02 PM
Posted On: 12-06-2020, 10:00 AMFL 4Motion liked post by jchammond On thread : Adding more than max oil levelBack in the “Old-School” days, 10# per 1k rpm’s was acceptable...but idk on that particular engine :ugh2:Liked On: 12-06-2020, 07:02 PM
Posted On: 12-06-2020, 03:34 AMFL 4Motion liked post by Rusty On thread : Adding more than max oil levelSounds like he's got the wrong size bearings.Liked On: 12-06-2020, 07:01 PM
Posted On: 12-06-2020, 01:37 AMFL 4Motion liked post by DrBacon On thread : Adding more than max oil level.Liked On: 12-06-2020, 07:01 PM
Posted On: 12-06-2020, 01:18 AMFL 4Motion liked post by JARblue On thread : Autonomous DrivingWhat happens when I get a rental car with the $15 insurance and then try to merge into the fast lane with a high speed train of COCs? :DLiked On: 12-06-2020, 06:57 PM
Posted On: 12-06-2020, 09:40 AMFL 4Motion liked post by Rusty On thread : The new “what did you do to your Z today” (with off topic replies) XXXVIIINetflixing it tonight.Liked On: 12-05-2020, 08:58 PM
Posted On: 12-05-2020, 08:32 PMFL 4Motion liked post by Spooler On thread : The new “what did you do to your Z today” (with off topic replies) XXXVIIIDang truck's pinion seal change is being a pain in the butt. Had to call JC several times. I think I have the right puller now to get the freaking yoke off. Off to get longer bolts in the morning for...Liked On: 12-05-2020, 08:57 PM
Posted On: 12-05-2020, 07:58 PMFL 4Motion liked post by Spooler On thread : Shell Rotella T6 15W-40?The reason you are burning oil is more than likely due to the ring gap was set too large causing this issue. Normal for a Forced induction car. There is a fine line setting the ring gaps. Too large...Liked On: 12-05-2020, 08:54 PM
Posted On: 12-05-2020, 07:45 PMFL 4Motion liked post by Spooler On thread : Adding more than max oil levelThat doesn't happen. The oil stays in the lines and dose not drain back to the oil pan. I have had a many a turbo car with oil coolers. I do fill up to just below the full line. When the car is shut...Liked On: 12-05-2020, 07:34 PM
Posted On: 12-05-2020, 07:25 PMFL 4Motion liked post by Leingod On thread : The new “what did you do to your Z today” (with off topic replies) XXXVIIINo koks in it. I promise. It's a fun movie. Decent twist at the end.Liked On: 12-05-2020, 07:19 PM
Posted On: 12-05-2020, 07:13 PM
All times are GMT -5. The time now is 07:38 AM.