2011 Nismo#91

Engine & Drivetrain:
GTR TT by Driven Motorsport
AAM Mid Pipe and Remark Axle back V2 w/ QTP cut outs.
Ecutek tune
35 Row Sterab Oil Cooler
13row PS cooler
CJM Baffled Oil Pan
CJM Fuel Starvation Fix Kit
Zspeed clutch flywheel HDslave SS clutch line
Quaife Diff and Whitleline diff bushings
CFS radiator

Exterior & Interior:
Oneighty (Landing Strip, Dual Led Orb, Housing Black Projectors Grey)
RPM Roll Bar 4 Point with SFI 45 Padding
Schroth Profi II Hans 6PT Camlock Harness
A-pillar Oil pressure and AFR
Amerex Handheld Extinguisher - Halon 2.5lb

Wheels & Tires:
19" Stock 2011 Nismo Wheels with Continental Extreme Contact Sport 02 275/35ZR19 and 305/30ZR19
18" Base wheels with Michelin X-Ice 225/50R-18 and 245/45R-18

Brakes & Suspension:
XP10 fronts and XP8 Rears
FrozenRotors
Z1 Stainless steel brake lines
JRZ RS Pro F(10R/10C) R(10R/6C) 1000inlbs Coil + 150inlbs Tender
SPL:
TITANIUM Rear Toe Arms; Rear Swaybar Endlinks; Eccentric Lockout Kit; TITANIUM Rear Traction Arms; Front Upper Camber Arms; FKS Front Lower Arm Bushings; TITANIUM Rear Camber Arms; FKS Rear Knuckle Monoball Bushing Set; Solid Subframe Bushings; FKS Rear Upper Arm Monoball Bushings; Front Endlinks

Audio & Video:
Kenwood Excelon DMX958XR
VanTop H612 Dashcam and Rearview camera mirror
Hertz HKS 165 System
Alpine PDX-F4 4 Channel amplifier
Rockfordfosgate R750-1D Mono amplifier
JL 13TW5-3 600W Sub with Wicked CAS box & rear trunk mat.

congrats on your z Welcome aboard

Hello. New Z owner here. Well, its been a bit over a year now since I secured my 2015 Z. I love it, it's the best purchase I've ever made. It's not my daily driver so I keep it garaged for several...

So, we can all agree that the giant wing, knockoff wheels and dildo shift knob is pretty much the "daddy should have pulled out" car enthusiast starter kit? Edit - Is it hilarious to anyone else...

So I got to checking all of the fuses in the Intelligent Power Distribution Module located by the battery and came across the 15A ‘ENG CNTRL’ blown. I replaced this fuse and sure enough this was the...

He won't be pulled over ever again.

Version 2.0 coming soon :) Relocated first wastegate and added 2nd 44mm Tial wastegate. I should have everything welded by tomorrow ...

Unless it is too late, get the Z1 CSC Elimination Kit instead of replacing the CSC. My Z used to run like a dog whenever the temperature rose above 85...I ran it hard with the kit installed at about...

Aren't you supposed to be worried when it's not hard in the morning?

Just got off the phone with bryan and we are set for tomorrow. All heat cycles went well and he plans on disconnecting the exhaust to see if my existing is bottlenecking while on the dyno.. May need...

Lesson learned kids. Save up your money and buy quality material. Glad you got your money back but when it comes to cars, health, and food…never cheap out.

Go with the one that looks the best to you because that's all your paying for.

I was going to bet that you throw the rod in cylinder 5 before you reach 600 hp :stirthepot: But then I remembered Bryan is doing the work, not Bobby :icon17: Good luck with your numbers...

Clean it and if the crude comes back you have a leak. If it doesn't then you are golden.

http://www.nerocam.com/SCC_Images/image033.jpg

almost fixed...

Just wanted to post this in case anyone else starts running into problems. As when i was searching and reading through potential problems here as i tried to start my car and wait for the tow truck i...