jwick Build Thread - First BP - G37T in existence
 

Welcome everyone. The following will detail my efforts to be the first G37 with a BP Twin Scroll Turbo kit. I selected the BP kit for several reasons. The primary, or 1A, being that it is completely DIYable and I prefer to be the one working on my car. 1B is the fact that Sasha’s customer service is second to none. This build has/will take place over a couple months as I get everything ready to go. I will try my best to keep everything up to date and of course include as many pictures as possible. As with any 1st time build, I will likely need some assistance along the way so I definitely appreciate all those willing to provide applicable advice.

On to the good stuff…

I bought the car in May of 2010. I had the first mods purchased prior to the car even having 1,200 break-in miles. I worked on it for the first 18 months or so and it’s basically been the same ever since. Mods pre-FI, in order of install best I can remember:

- Stillen CBE
- Eibach Proset Spring Kit
- GT Spec Strut Bar
- Stillen Gen 3 Intake
- Berk HFCs
- UpRev Tune from JTran
- Hotchkis Sways
- SPC Front Control Arms
- Whiteline Diff Bushings
- Whiteline Rear End Links
- NISMO Diff Cover
- And I’m sure there’s a mod or two I forgot along the way

Current NA mods staying on the car:

- Stillen CBE (minus Y-Pipe)
- Eibach Proset Spring Kit
- GT Spec Strut Bar
- Hotchkis Sways
- SPC Front Control Arms
- Whiteline Diff Bushings
- Whiteline Rear End Links
- NISMO Diff Cover

Turbo Build List:

- BP Twin Scroll Turbo Kit (Precision 6266 Turbo – Ball Bearing Upgrade) – See Boosted Performance Profile Page for complete details
- GReddy Oil Filter Relocation Adapter (added Thremostat to Oil Cooler)
- CSF 7012 Radiator
- Z1 Motorsports Full Face Clutch/Flywheel
- Z1 Motorsports Silicone Radiator Hoses
- ZSpeed CSC
- GReddy Profec 2 Spec B Boost Controller
- Innovate LC-2 and DB Gauge
- GReddy Multi D/A Gauge (Boost/Oil Temp/Oil Pressure/Water Temp/Fuel Pressure)
- A fucton of heat management items (header wrap, thermo-tec, inferno heat shield, turbo bag, etc.)

Goals:

- Fun!
- Satisfaction of installing it all myself (with some help from good friends and support from the GF since she never complains about money spent or time involved)
- 400wft-lbs on a DynoJet with the most area under the curve as possible. The key is as much as I can get ensuring reliability.

Special Thanks go to:

- First and foremost, Sasha for building a top notch DIY kit and being the definition of customer service
- Awesome Z (clutch install – only part not DIY)
- Chuck33079 (my boy – main man on the install assistance and the one that pushed me over the cliff to pull the trigger on this ‘little’ project)
- JTran (Custom Turbo Tune among other support related stuff)
- O&G (confirmation of product selection and general knowledge, plus almost as much enthusiasm as Chuck and I for this build)
- Z1 Motorsport (Jon is a righteous individual always willing to provide platform knowledge and make sure you are getting exactly what you need)
- GaleForce - working with me to create his first G37 custom Double Pod A-Pillar (pics included further back)
- Phunk - helping source GReddy multi-guage pressure sender to mate with his multi-adapter (pics included further back)
- Tony (Fast Intentions) - working with me to supply a custom G37 exhaust to allow me to custom fab the appropriate connections to the turbo downpipe
- jlo370z - fellow BP brotha support and being there to swap crank case filters with me
- Nathan - genius behind all the electrical/wiring magic
- Reservation – place holder for forum members that I know will be more than willing to provide build assistance considering how wonderful this community is

Pre-tear down
http://i1155.photobucket.com/albums/...ps82da718a.jpg

Pile of stuff going on the car
http://i1155.photobucket.com/albums/...ps457b5985.jpg

We spent all of Thursday night doing preliminary checks to make sure that this kit would indeed bolt-up on a G37. We test fit the FMIC and then reinstalled the bumper. We also checked the first charge pipe to make sure it routed the same way as on a Z.

Pre-check out prior to full tear down.
http://i1155.photobucket.com/albums/...ps76ce3245.jpg
http://i1155.photobucket.com/albums/...ps97146d15.jpg

FMIC Check
http://i1155.photobucket.com/albums/...ps726010cd.jpg

Another test fit pic
http://i1155.photobucket.com/albums/...psefe9d279.jpg

Exa Pump Installed (the first time...detail that out later)
http://i1155.photobucket.com/albums/...ps193057ed.jpg

GReddy Plate Installation:

Bracket Removed
http://i1155.photobucket.com/albums/...psfed96a3a.jpg

Grinding Wheel
http://i1155.photobucket.com/albums/...pseceb95f1.jpg

GReddy Mounted (used a pneumatic right angle drill to drill the sub-frame. The lag bolts were hard enough to self-tap as they went in)
http://i1155.photobucket.com/albums/...ps961cda29.jpg

Modified Oil Filter Setup (Added GReddy Thermostat Plate)
http://i1155.photobucket.com/albums/...psb4b2e2ef.jpg

GReddy Thermostat with Oil Temp Probe Installated
http://i1155.photobucket.com/albums/...ps2edb6979.jpg

Modified Turbo feed line for both OEM and After Market Oil Pressure Sender
http://i1155.photobucket.com/albums/...ps5873b18b.jpg

Oil Pan Removed
http://i1155.photobucket.com/albums/...ps391adf65.jpg

Cleaning Oil Pan Surface
http://i1155.photobucket.com/albums/...ps52788627.jpg

Spacer RTVed
http://i1155.photobucket.com/albums/...ps4985dd9f.jpg

There are a lot of braided oil lines routing behind the radiator.
http://i1155.photobucket.com/albums/...ps9b9271c4.jpg

End of Day one...

Day two we had to adjust some things so it was a lot of two steps forward and one back. Not unexpected since this was the first go around on a G37.

So the only major issue we came up with getting this kit to fit on a G37 is that the Exa pump hits the stock S bumper.

Interference Location
http://i1155.photobucket.com/albums/...ps9edfb2b0.jpg

Stock G 'S' Bumper (can only get a 6MT in a S so all BP-G37s will have this issue if running stock bumper)
http://i1155.photobucket.com/albums/...ps7aeff74e.jpg

So the solution we came up with, which turned out really easy, was to move the Exa pump from the right set of frame bolts to share the same mounting location as the FMIC. This required us to cut a bunch of zip ties and readjust Friday's oil line routing but all in all a pretty easy solution. I know the cuts I made are not the prettiest but considering it cannot be seen once the bumper was on I was not willing to stop working to run to Lowe's for the proper Dremel cutting tool. (FYI...I think we could have gotten away without cutting if you placed the flare nut behing the pump bracket housing before you started threading it but I wanted it where I could pull it without a second pair of hands.)

New Location fro Exa Pump
http://i1155.photobucket.com/albums/...ps89683b94.jpg

HFCs removed and prepping for Crossover Pipe Install
http://i1155.photobucket.com/albums/...ps9516b57c.jpg

Crossover Pipe Installed
http://i1155.photobucket.com/albums/...psf58296e2.jpg
http://i1155.photobucket.com/albums/...ps42609446.jpg

Final routing for oil lines and charge pipe (had to move everything once I test fit the sway bar and realized we had some interference)
http://i1155.photobucket.com/albums/...psc8f43dbd.jpg

Turbo Mounted
http://i1155.photobucket.com/albums/...psc792641d.jpg
http://i1155.photobucket.com/albums/...psb9bd36f0.jpg

Remainder of Hotside Piping
http://i1155.photobucket.com/albums/...ps17109030.jpg
http://i1155.photobucket.com/albums/...psae93ab36.jpg
http://i1155.photobucket.com/albums/...ps292775e1.jpg

Weekend Intermission:
Look how much less is on that table. Much appreciation to Chuck for all his help!
http://i1155.photobucket.com/albums/...ps88709367.jpg

I love how the Turbo Box says Boosted Performce. Sasha, did you pay extra for that?:rofl2:
http://i1155.photobucket.com/albums/...psa60edd56.jpg

Good job fellas!

Thanks Mr. GaleForce. You know there will be some interior pics of that beautiful gauge double pillar!

Can't wait to see the final shots / #s


Sent from my iPhone using Tapatalk

So everything fit so far except a few minor modifications I am guessing? looks good so far too.

I finally know what Chuck looks like now, love the wrap job! We will get #'s on JTrans low reading Mustang and then all go to a dynojet in town and get the numbers everyone cares about! Red silicon FTW, that sh*t is boss!

I'll see you soon my low mount friend!

And damn you Chuck and your badass garage!

Yes sir. I forgot to mention that I had to modify the way you handle the PS Cooler as the one in the G is about 3-4" longer than that in a Z so the way Sasha moves it back won't work.

Long story short I bent the hardline bracket a little and zip tied the right side of the cooler itself to the vertical support in the middle of the radiatior that supports the hood latch and the left side I zip tied to the condenser air dryer.

Everything else in my build were just options I added to the kit (i.e. GReddy Thermostat Plate and Aftermarket Fuel Pressure Sender) and would be identical on a Z.

Thanks man! Getting back at it Thursday after work and should be doing leak tests and first lite boost runs on Saturday.

Let me tell you that wrapping that crossover pipe almost cost me a GF (she was my second pair of hands in the process) and was by far the most difficult thing I've wrapped to date. It's a shame that that's the best it'll ever look. After a few heat cycles it'll be completely different.

Red is nice but I like the blue contrast on the graphite. Not to mention both you and Chuck have red going on.

looks so clean! good job

Awesome Job!!

P.S, Love the "Colon Blow" Shirt. LOL

Thanks :tiphat:

I can't take credit for that one. That's Chuck but I included that specific pic because it was awesome!

Looking good man, there's nothing like doing it yourself...

I agree. It'll be nice knowing we built it

Sent from my SPH-L710 using Tapatalk

Great progress so far, can't wait to see it done !

:tiphat:

I think the crick in my neck from sitting under the car trying to get that goddamn turbo clocked right is starting to go away.

:werd:

My shoulders are still pretty sore from lifting that 25lb bitch several reps. I can honestly say I'm not looking forward to the next air filter change.

I'm so excited that a good portion of the remaining steps can be accomplished standing up.

Great work J! In for updates!

:rofl2: No, I did not pay anybody for that. Maybe I should be going after Precision Turbo for putting my name on their boxes.



Thank you for taking the time and documenting the build. As I suspected, the kit would fit, with very minor alterations.

I also noticed that the mounting tabs on the FMIC are significantly smaller than they were in the past. Will talk to the suplier about the inconsistency of this. It explains why a couple of customers had questions. Those tabs used to be about 2", so there was a lot of room to play with, and the aluminium is easy to drill through.

:tup:
Coming along nicely, looking forward to see this on the street!

We'll be back at it this weekend. If you've freed up from wedding stuff stop on by if for nothing more than to shoot the **** and drink a couple beers

Sent from my SPH-L710 using Tapatalk

Sweet :tup:

I think I'm bringing the beer for Saturday - I'm exchanging beer for some of Chuck's OEM parts on Wednesday :icon17:

You staying in town or headed directly back to A-town?

Sent from my SPH-L710 using Tapatalk

Done with wedding stuff, will see what I have planned this weekend.
My exhaust hanger connected to my muffler snapped and need to get that welded back. Been going nonstop at work since I got back from wedding stuff because an office got a terrible virus and I had the joy of cleaning it up. :shakes head:

We're staying with some friends near Chuck on Wednesday night before we leave for a weekend cruise to Cozumel the following morning out of Galveston :tup:

I'm looking forward to checking out his lift and looking at the G :yum:

I only live a few miles away. Might stop by if y'all give me the heads up

Sent from my SPH-L710 using Tapatalk

....def sub'd!

sweet!!! I already have this kit as my 1st choice for FI when I get the $$. This kit is just plain AWESOME. It's going to be fun installing and fun boosting when it's all installed. So glad to know there is a local to help if needed.

We have a whole group of FI VQ locals willing to turn a wrench or two for a fellow low mount buddy! Can't go wrong w/ this setup!

We are building quite an army of boosted VQs

:rock:

Sent from my SPH-L710 using Tapatalk

I was thinking posting on the Texas forum of how it would be cool to have a bunch on Z's go to the 1/4 mile and run. We could chat as we push put cars to the line.

None of us boosted guys would hook up

Sent from my SPH-L710 using Tapatalk

Damn, I need to move to Texas.

Yeah... you can drive the Z all year long :o

Sent from my SPH-L710 using Tapatalk

Weathers decent most the time, economy is top notch, huge horsepower scene, hot girls, great food, hi speed limits, great scenery (coastal, hill country, dense forest, mountains, deserts and grass lands) and we don't relate much to the rest of the country! You know you always have a spot to crash if you do decide to make a trip!