Mike's Journal

Mike · 12-01-2012, 07:08 PM

Quote:

Originally Posted by HKYStormFront

mike that cage looks awesome man!

Thanks!

Did an oil change today, swapped out to Valvoline VR1 race oil, since I can pick it up locally instead of ordering online. Also flushed the brake fluid and moved the trunk opener out to the license plate area. Already had a hole drilled from the cabin from when I had my laser shifters installed.

Mike · 12-03-2012, 09:30 AM

Secured the door pulls and relocated trunk release outside of car. Using zip ties for handles, for now.

Bought some little rubberized clamps from Lowe's, powdercoated them satin black and used factory holes for anchors:

anchored this one down inside and have it just sticking out the back license plate hole. I was going to have it on the inside, right behind my drivers seat, but with the wing, it requires pulling on it while simultaneously lifting the hatch, and the car doesn't lock anymore anyways.

sig11 · 12-03-2012, 03:45 PM

Looks nice, Mike!

Sh0velMan · 12-23-2012, 09:33 PM

Mike, do you have any advice or tips on how to go about removing the electric locks from the car?

I can't find a safe way to unlock and open the door in one pull so I'm going to remove the lockers.

Mike · 12-24-2012, 09:20 AM

I don't recall it being too hard. The drivers side was a little difficult, had to unbolt the lock mechanism and the door handle to remove the cables connecting them. the passenger side was just the lock mechanism, then I cut all the wires going into the door and removed them. Didn't do anything with the trunk mechanism, but it doesn't work now because of the wire removal in the drivers door.

Sh0velMan · 12-24-2012, 11:18 PM

Cool was able to remove the locking mechanism and handle. Gave me a great excuse to use my new cordless impact.

Can I ask why you cut the harness instead of just unhooking it from the car (big connector on the side inside the hinge area) and pulling it out?

Also took out the dampener and removed the cable spool and supporting hardware. Used a cabling ferrule to permanently attach the two cables. Good pound there.

I'll post completed photos to my build thread if you wanna see how I did the linkages and whatnot. Prolly tomorrow or Wednesday I'll finish.
.

SPOHN · 12-25-2012, 05:54 AM

Quote:

Originally Posted by Sh0velMan

Can I ask why you cut the harness instead of just unhooking it from the car (big connector on the side inside the hinge area) and pulling it out?

How to you unplug this harness? I've looked at for awhile and can't figure it out. It's different from your typical harness. Must come unplugged fron the iside of the cab.

Mike · 12-25-2012, 08:29 AM

I didn't look far enough in to see the harness, just took the easy route with wire cutters.

Sh0velMan · 12-25-2012, 09:02 AM

Grab the textured piece at the very top and pull out and down like a giant power switch.

Sent from my SAMSUNG-SGH-I717 using Tapatalk 2

Sh0velMan · 12-25-2012, 10:22 AM

Quote:

Originally Posted by Sh0velMan

Grab the textured piece at the very top and pull out and down like a giant power switch.

Sent from my SAMSUNG-SGH-I717 using Tapatalk 2

Here's some crappy photos.

Note that after you do this, you need to seal the hole to keep water out. If you still have your dash out, just remove the matching connector from the inside of the car and tape over the hole.

SPOHN · 12-25-2012, 10:30 AM

I thought that had something to do with it.

The first time I couldn't get the harness to release from the inside for it had no clip lock to release and pull from. Thanks, repped.

Sh0velMan · 12-25-2012, 10:40 AM

Quote:

Originally Posted by SPOHN

I thought that had something to do with it.

The first time I couldn't get the harness to release from the inside for it had no clip lock to release and pull from. Thanks, repped.

Cool. Just can't stress enough tho, don't leave that hole open. Water will get on live contacts inside the connector, or if you remove it, directly down into your fuse box or onto your ECU/BCM depending on which side of the car you're talking about.

SPOHN · 12-25-2012, 10:43 AM

Quote:

Originally Posted by Sh0velMan

Cool. Just can't stress enough tho, don't leave that hole open. Water will get on live contacts inside the connector, or if you remove it, directly down into your fuse box or onto your ECU/BCM depending on which side of the car you're talking about.

I have this stuff called aqua seal we use at work. Works great for this. Then I'll seal it up with a small bracket. I have sevaral holes to covor know with the heater core gone.

Sh0velMan · 12-25-2012, 10:45 AM

Quote:

Originally Posted by SPOHN

I have this stuff called aqua seal we use at work. Works great for this. Then I'll seal it up with a small bracket. I have sevaral holes to covor know with the heater core gone.

Sweet. Post pics of what you do with the giant blower inlet hole. Still trying to figure out what to do with that myself rofl.

(Or are you leaving the cowling intact? I removed mine, great ventilation out of the back of the hood now)

SPOHN · 12-25-2012, 10:46 AM

I removed the cowling also

12-03-2012, 09:30 AM	#362 (permalink)
Mike The370Z.com Sponsor Join Date: Jun 2009 Location: Loganville, GA Posts: 5,944 Drives: 370z Rep Power: 2185	Secured the door pulls and relocated trunk release outside of car. Using zip ties for handles, for now. Bought some little rubberized clamps from Lowe's, powdercoated them satin black and used factory holes for anchors: anchored this one down inside and have it just sticking out the back license plate hole. I was going to have it on the inside, right behind my drivers seat, but with the wing, it requires pulling on it while simultaneously lifting the hatch, and the car doesn't lock anymore anyways. ChrisSlicks likes this. __________________ NISSAN: 75 280Z / 86 300ZX GLL /87 Sentra SE / 03 350Z / 23 Z Porsche: 93 968 / 23 Macan GTS / 93 968

12-23-2012, 09:33 PM	#364 (permalink)
Sh0velMan A True Z Fanatic Join Date: Jan 2012 Location: Dallas/Ft.Worth Posts: 3,349 Drives: Noisily. Rep Power: 20	Mike, do you have any advice or tips on how to go about removing the electric locks from the car? I can't find a safe way to unlock and open the door in one pull so I'm going to remove the lockers. __________________ Buy My Car! \| Build Thread

12-24-2012, 09:20 AM	#365 (permalink)
Mike The370Z.com Sponsor Join Date: Jun 2009 Location: Loganville, GA Posts: 5,944 Drives: 370z Rep Power: 2185	I don't recall it being too hard. The drivers side was a little difficult, had to unbolt the lock mechanism and the door handle to remove the cables connecting them. the passenger side was just the lock mechanism, then I cut all the wires going into the door and removed them. Didn't do anything with the trunk mechanism, but it doesn't work now because of the wire removal in the drivers door. __________________ NISSAN: 75 280Z / 86 300ZX GLL /87 Sentra SE / 03 350Z / 23 Z Porsche: 93 968 / 23 Macan GTS / 93 968

12-24-2012, 11:18 PM	#366 (permalink)
Sh0velMan A True Z Fanatic Join Date: Jan 2012 Location: Dallas/Ft.Worth Posts: 3,349 Drives: Noisily. Rep Power: 20	Cool was able to remove the locking mechanism and handle. Gave me a great excuse to use my new cordless impact. Can I ask why you cut the harness instead of just unhooking it from the car (big connector on the side inside the hinge area) and pulling it out? Also took out the dampener and removed the cable spool and supporting hardware. Used a cabling ferrule to permanently attach the two cables. Good pound there. I'll post completed photos to my build thread if you wanna see how I did the linkages and whatnot. Prolly tomorrow or Wednesday I'll finish. . __________________ Buy My Car! \| Build Thread

12-25-2012, 08:29 AM	#368 (permalink)
Mike The370Z.com Sponsor Join Date: Jun 2009 Location: Loganville, GA Posts: 5,944 Drives: 370z Rep Power: 2185	I didn't look far enough in to see the harness, just took the easy route with wire cutters. __________________ NISSAN: 75 280Z / 86 300ZX GLL /87 Sentra SE / 03 350Z / 23 Z Porsche: 93 968 / 23 Macan GTS / 93 968

12-03-2012, 03:45 PM	#363 (permalink)
sig11 A True Z Fanatic Join Date: Jun 2009 Location: Detroit Posts: 1,294 Drives: 09 370Z Red Sport-MT Rep Power: 17	Looks nice, Mike!

12-25-2012, 09:02 AM	#369 (permalink)
Sh0velMan A True Z Fanatic Join Date: Jan 2012 Location: Dallas/Ft.Worth Posts: 3,349 Drives: Noisily. Rep Power: 20	Grab the textured piece at the very top and pull out and down like a giant power switch. Sent from my SAMSUNG-SGH-I717 using Tapatalk 2 __________________ Buy My Car! \| Build Thread

12-25-2012, 10:30 AM	#371 (permalink)
SPOHN A True Z Fanatic Join Date: Feb 2010 Location: Covington, GA Age: 45 Posts: 14,844 Drives: Waiting on next Z Rep Power: 221	I thought that had something to do with it. The first time I couldn't get the harness to release from the inside for it had no clip lock to release and pull from. Thanks, repped. __________________

12-25-2012, 10:46 AM	#375 (permalink)
SPOHN A True Z Fanatic Join Date: Feb 2010 Location: Covington, GA Age: 45 Posts: 14,844 Drives: Waiting on next Z Rep Power: 221	I removed the cowling also __________________

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
wstar's Journal	wstar	Member's 370Z Gallery	865	12-28-2019 09:15 AM
TravisJB Journal	travisjb	Member's 370Z Gallery	1977	11-03-2017 09:39 AM
RCZ's 370Z Journal.	RCZ	Member's 370Z Gallery	1743	08-09-2013 11:55 PM
KillerBee370's journal	KillerBee370	Engine & Drivetrain	100	08-18-2010 01:58 PM
LiquidZ's Journal	LiquidZ	Member's 370Z Gallery	22	05-22-2009 11:42 PM