flashburn's 370Z Journal, Project: FlasHBurN Commences!

flashburn · 08-22-2010, 06:45 PM

I've been slacking off and wanting to make a journal for a while, so here we go!

Goal:
Ultimately I want to do 3-4 HPDE's a year, along with possibly some AutoX mixed in. I also use this car to commute about 70 miles a day so I want to stay N/A. I'd like to do my first HPDE around the end of this year.

I'm going to keep the list of modifications limited to performance, and not mention any of my aesthetic modifications or audio gear. I solely want this journal to be about my journey into the world of motorsports.

Current Modifications:

Fast Intentions CBE with 18" Carbon Fiber Canisters

Fast Intentions Non-Resonated HFC's

K&N Dropin Filters

(gone) Cobb AccessPort with Canned AAM Tune

H&R 15mm (front) and 20mm (rear) Wheel Spacers

Hankook 265/35/19F and 285/35/19R

SRPracing Pedals (+10whp!)

Future Modifications (Soon!):

Stillen G3 CAI (Sitting in my house now)

UpRev Osiris with E-Tune. I'm ditching the Cobb AP under the 100% satisfaction guarantee they have. If they don't want to support the 370Z then I don't want to support them.

Future Modifications (~6 Months):

These are the mods I need to have done before I do my first HPDE.
Oil Cooler (Not sure on brand/size yet)

Brake Pads (Dedicated Track Pads)

Future Modifications (~1 Year):

S.S. Brake Lines, probably these Z1 Braided Stainless Brake Lines

Motul RBF 600 Brake Fluid (while I'm already replacing the lines)

Rotors

Dedicated Track Wheels + Tires. Hoping to snatch up a set of Base 18" Wheels from someone for cheap.

Sway Bars

Future Modifications (Not Definite/Distant Future):

As always, open to suggestions if you guys think of any other parts I should get.

flashburn · 08-22-2010, 06:46 PM

Photos:

( Click to show/hide )

flashburn · 08-22-2010, 06:46 PM

Videos:

flashburn · 08-22-2010, 06:47 PM

I had the exhaust, HFC's, and spacers installed professionally. However, my goal is to do all future mod's (within reason) myself. Currently I do not own too many tools that are required, so I plan on building them up over time. My first mod is going to be the Stillen G3 CAI's that I bought used from another member here. I'm going to be buying a dremel and a torque wrench for that install, I have the other tools needed for this job already.

flashburn · 08-22-2010, 06:59 PM

Anyone have any recommendations for a torque wrench? I really don't want to pay the $80+ Lowes and Home Depot are charging for one. Amazon has a bunch of them ranging from $30 to over $100. Preferably I'd like to spend no more than $50.

Jamaica · 08-22-2010, 07:09 PM

Quote:

Originally Posted by flashburn

I had the exhaust, HFC's, and spacers installed professionally. However, my goal is to do all future mod's (within reason) myself. Currently I do not own too many tools that are required, so I plan on building them up over time. My first mod is going to be the Stillen G3 CAI's that I bought used from another member here. I'm going to be buying a dremel and a torque wrench for that install, I have the other tools needed for this job already.

Great start. The intakes are really easy to install. Just follow the instructions. The stillen instakes are super easy to install.

flashburn · 08-23-2010, 12:52 PM

Would this be a decent choice for a Torque Wrench?

Amazon.com: Michigan Industrial Tools 1/4" Drive Click Torque Wrench 20 - 200" lb: Home Improvement

I keep seeing all different size drives (1/4", 1/2", 3/4", etc), which should I be looking at? Not even sure what the drive size means.

cjof2003 · 08-23-2010, 02:11 PM

The drive size is the size sockets that will fit the wrench onto the square part of the wrench. That wrench has a 1/4" square on it, so you will need sockets with a 1/4 square fitting, or an adapter piece.

flashburn · 08-23-2010, 04:02 PM

Quote:

Originally Posted by cjof2003

The drive size is the size sockets that will fit the wrench onto the square part of the wrench. That wrench has a 1/4" square on it, so you will need sockets with a 1/4 square fitting, or an adapter piece.

Ah okay, I had a feeling that was it. I'll check my current sockets, but I'm pretty sure they are 1/4".

Will 20/200ft-lb be a good enough range to do anything I'm going to need to do with my car?

memorylasts · 08-23-2010, 04:57 PM

Quote:

Originally Posted by flashburn

Ah okay, I had a feeling that was it. I'll check my current sockets, but I'm pretty sure they are 1/4".

Will 20/200ft-lb be a good enough range to do anything I'm going to need to do with my car?

The axel bolt(s) will possibly require more, im not sure about anything else. My suggestion is to go with a smaller range and buy maybe 2 instead of one, it will be more accurate that way.

Not sure exactly where you are looking, but maybe like 25-100, and 80-???

Just figure out what you need for the job, because that 20-200 might be to big to get into certain areas. If it is a cost thing buy the one you need now, if it isnt then break it down so they over lap by about 20ft/lbs.

Its been a while since i have really needed one so i apologize if my numbers are off in advance.

flashburn · 08-23-2010, 05:01 PM

Cool, thanks for the info. So it looks like I need 38ft-lbs for the engine brace, and 80-90ft-lb for the lugs. I'll look for one with a smaller range then. When (if) I need one with more torque I'll buy it then.

flashburn · 08-23-2010, 05:16 PM

Hmm, I can't seem to find one with a smaller range that isn't $90+.

FL 4Motion · 08-23-2010, 07:17 PM

check out Harbor Freight, they've got decent tools at very competitive prices. that's where I got my torque wrench. It's a 1/2 " drive though.

PS--I don't believe the 18" stockers will clear the Akebono brakes, I would just use the stock wheels for the track and pick up some nice ones for the street or get a set of different dedicated track wheels.

flashburn · 08-23-2010, 07:26 PM

Quote:

Originally Posted by FL 4Motion

check out Harbor Freight, they've got decent tools at very competitive prices. that's where I got my torque wrench. It's a 1/2 " drive though.

PS--I don't believe the 18" stockers will clear the Akebono brakes, I would just use the stock wheels for the track and pick up some nice ones for the street or get a set of different dedicated track wheels.

Okay, I'll check out Harbor Freight.

I've heard others say that they have used the stock Base wheels with the sports brakes successfully. I'm hoping that this setup would work fine, since people tend to sell the base wheels + tires for around $800 shipped usually.

flashburn · 08-23-2010, 07:29 PM

Wow, the Harbor Freight ones are pretty damn cheap:
$19.99 for 1/4" 20-200ft-lb
1/4" Drive Click Stop Torque Wrench
$24.99 for 1/2" 20-150ft-lb
1/2" Drive Click Stop Torque Wrench

08-22-2010, 06:45 PM	#1 (permalink)
flashburn A True Z Fanatic Join Date: May 2009 Location: Central Florida Posts: 1,884 Drives: '12 Corvette GS 6M Rep Power: 18	flashburn's 370Z Journal, Project: FlasHBurN Commences! I've been slacking off and wanting to make a journal for a while, so here we go! Goal: Ultimately I want to do 3-4 HPDE's a year, along with possibly some AutoX mixed in. I also use this car to commute about 70 miles a day so I want to stay N/A. I'd like to do my first HPDE around the end of this year. I'm going to keep the list of modifications limited to performance, and not mention any of my aesthetic modifications or audio gear. I solely want this journal to be about my journey into the world of motorsports. Current Modifications: Fast Intentions CBE with 18" Carbon Fiber Canisters Fast Intentions Non-Resonated HFC's K&N Dropin Filters (gone) Cobb AccessPort with Canned AAM Tune H&R 15mm (front) and 20mm (rear) Wheel Spacers Hankook 265/35/19F and 285/35/19R SRPracing Pedals (+10whp!) Future Modifications (Soon!): Stillen G3 CAI (Sitting in my house now) UpRev Osiris with E-Tune. I'm ditching the Cobb AP under the 100% satisfaction guarantee they have. If they don't want to support the 370Z then I don't want to support them. Future Modifications (~6 Months): These are the mods I need to have done before I do my first HPDE. Oil Cooler (Not sure on brand/size yet) Brake Pads (Dedicated Track Pads) Future Modifications (~1 Year): S.S. Brake Lines, probably these Z1 Braided Stainless Brake Lines Motul RBF 600 Brake Fluid (while I'm already replacing the lines) Rotors Dedicated Track Wheels + Tires. Hoping to snatch up a set of Base 18" Wheels from someone for cheap. Sway Bars Future Modifications (Not Definite/Distant Future): As always, open to suggestions if you guys think of any other parts I should get. __________________ Current Ride: 2012 Chevrolet Corvette Grand Sport Centennial Edition Carbon Flash 6M Previous Ride: 2009 Nissan 370Z Sport Platinum Graphite 7AT

08-22-2010, 06:46 PM	#2 (permalink)
flashburn A True Z Fanatic Join Date: May 2009 Location: Central Florida Posts: 1,884 Drives: '12 Corvette GS 6M Rep Power: 18	Photos: ( Click to show/hide ) __________________ Current Ride: 2012 Chevrolet Corvette Grand Sport Centennial Edition Carbon Flash 6M Previous Ride: 2009 Nissan 370Z Sport Platinum Graphite 7AT Last edited by flashburn; 08-23-2010 at 07:50 AM.

08-22-2010, 06:46 PM	#3 (permalink)
flashburn A True Z Fanatic Join Date: May 2009 Location: Central Florida Posts: 1,884 Drives: '12 Corvette GS 6M Rep Power: 18	Videos: __________________ Current Ride: 2012 Chevrolet Corvette Grand Sport Centennial Edition Carbon Flash 6M Previous Ride: 2009 Nissan 370Z Sport Platinum Graphite 7AT Last edited by flashburn; 08-22-2010 at 06:50 PM.

08-22-2010, 06:47 PM	#4 (permalink)
flashburn A True Z Fanatic Join Date: May 2009 Location: Central Florida Posts: 1,884 Drives: '12 Corvette GS 6M Rep Power: 18	I had the exhaust, HFC's, and spacers installed professionally. However, my goal is to do all future mod's (within reason) myself. Currently I do not own too many tools that are required, so I plan on building them up over time. My first mod is going to be the Stillen G3 CAI's that I bought used from another member here. I'm going to be buying a dremel and a torque wrench for that install, I have the other tools needed for this job already. __________________ Current Ride: 2012 Chevrolet Corvette Grand Sport Centennial Edition Carbon Flash 6M Previous Ride: 2009 Nissan 370Z Sport Platinum Graphite 7AT

08-22-2010, 06:59 PM	#5 (permalink)
flashburn A True Z Fanatic Join Date: May 2009 Location: Central Florida Posts: 1,884 Drives: '12 Corvette GS 6M Rep Power: 18	Anyone have any recommendations for a torque wrench? I really don't want to pay the $80+ Lowes and Home Depot are charging for one. Amazon has a bunch of them ranging from $30 to over $100. Preferably I'd like to spend no more than $50. __________________ Current Ride: 2012 Chevrolet Corvette Grand Sport Centennial Edition Carbon Flash 6M Previous Ride: 2009 Nissan 370Z Sport Platinum Graphite 7AT

08-23-2010, 12:52 PM	#7 (permalink)
flashburn A True Z Fanatic Join Date: May 2009 Location: Central Florida Posts: 1,884 Drives: '12 Corvette GS 6M Rep Power: 18	Would this be a decent choice for a Torque Wrench? Amazon.com: Michigan Industrial Tools 1/4" Drive Click Torque Wrench 20 - 200" lb: Home Improvement I keep seeing all different size drives (1/4", 1/2", 3/4", etc), which should I be looking at? Not even sure what the drive size means. __________________ Current Ride: 2012 Chevrolet Corvette Grand Sport Centennial Edition Carbon Flash 6M Previous Ride: 2009 Nissan 370Z Sport Platinum Graphite 7AT

08-23-2010, 02:11 PM	#8 (permalink)
cjof2003 Base Member Join Date: Sep 2009 Location: Atlanta, GA Posts: 74 Drives: 02 Acura RSX Type S Rep Power: 15	The drive size is the size sockets that will fit the wrench onto the square part of the wrench. That wrench has a 1/4" square on it, so you will need sockets with a 1/4 square fitting, or an adapter piece.

08-23-2010, 05:01 PM	#11 (permalink)
flashburn A True Z Fanatic Join Date: May 2009 Location: Central Florida Posts: 1,884 Drives: '12 Corvette GS 6M Rep Power: 18	Cool, thanks for the info. So it looks like I need 38ft-lbs for the engine brace, and 80-90ft-lb for the lugs. I'll look for one with a smaller range then. When (if) I need one with more torque I'll buy it then. __________________ Current Ride: 2012 Chevrolet Corvette Grand Sport Centennial Edition Carbon Flash 6M Previous Ride: 2009 Nissan 370Z Sport Platinum Graphite 7AT

08-23-2010, 05:16 PM	#12 (permalink)
flashburn A True Z Fanatic Join Date: May 2009 Location: Central Florida Posts: 1,884 Drives: '12 Corvette GS 6M Rep Power: 18	Hmm, I can't seem to find one with a smaller range that isn't $90+. __________________ Current Ride: 2012 Chevrolet Corvette Grand Sport Centennial Edition Carbon Flash 6M Previous Ride: 2009 Nissan 370Z Sport Platinum Graphite 7AT

08-23-2010, 07:17 PM	#13 (permalink)
FL 4Motion A True Z Fanatic Join Date: Feb 2009 Location: FL Posts: 4,776 Drives: Baby Shark Rep Power: 701615	check out Harbor Freight, they've got decent tools at very competitive prices. that's where I got my torque wrench. It's a 1/2 " drive though. PS--I don't believe the 18" stockers will clear the Akebono brakes, I would just use the stock wheels for the track and pick up some nice ones for the street or get a set of different dedicated track wheels.

08-23-2010, 07:29 PM	#15 (permalink)
flashburn A True Z Fanatic Join Date: May 2009 Location: Central Florida Posts: 1,884 Drives: '12 Corvette GS 6M Rep Power: 18	Wow, the Harbor Freight ones are pretty damn cheap: $19.99 for 1/4" 20-200ft-lb 1/4" Drive Click Stop Torque Wrench $24.99 for 1/2" 20-150ft-lb 1/2" Drive Click Stop Torque Wrench __________________ Current Ride: 2012 Chevrolet Corvette Grand Sport Centennial Edition Carbon Flash 6M Previous Ride: 2009 Nissan 370Z Sport Platinum Graphite 7AT

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
LinPark's 370Z Journal	LinPark	Member's 370Z Gallery	60	07-27-2018 10:07 PM
LunaZ's 370Z Journal	LunaZ	Member's 370Z Gallery	54	11-29-2017 09:33 AM
RCZ's 370Z Journal.	RCZ	Member's 370Z Gallery	1743	08-09-2013 11:55 PM
LateralG'z 370Z Journal	LateralG'z	Member's 370Z Gallery	54	12-25-2010 05:27 PM
My 370Z Journal - The Evo Killer	EVO_Killer	Member's 370Z Gallery	57	09-01-2009 09:51 AM