DDM Project 370Z

Togo · 07-07-2009, 04:55 PM

I wouldn't put it past misprint, which is why i only claimed that i thought i read they were those sizes.

I thought it was odd though that they left the staggered for a non-staggered setup

M.Bonanni · 07-07-2009, 06:06 PM

New set of Nitto NT05 tires showed up today! 275/35/18 front 285/35/18 rear. We'll see how the less staggered setup does August 1st & 2nd. We'll also find out if running a wider and stickier tire up front will uncover any more weaknesses with the car. Hopefully not, fingers crossed. My biggest concern to be quite honest is the SPC Camber arms either hitting the top of the wheel wells and/or not holding the alignment settings under hard load.

miguez · 07-08-2009, 06:49 AM

Mike, you should be able to check the wheel well for impact marks when you swap tires before this event, correct? Keep us posted!

M.Bonanni · 07-08-2009, 10:20 AM

Quote:

Originally Posted by miguez

Mike, you should be able to check the wheel well for impact marks when you swap tires before this event, correct? Keep us posted!

Oh yeah, I will probably check for it even sooner than that.

Scott@FontanaNissan · 07-08-2009, 10:27 AM

Hey Mike! so do you think maybe I can drive it???

M.Bonanni · 07-08-2009, 10:30 AM

Quote:

Originally Posted by Scott@FontanaNissan

Hey Mike! so do you think maybe I can drive it???

Sure

Scott@FontanaNissan · 07-08-2009, 11:01 AM

Of course you would let me....wouldn't ya???

M.Bonanni · 07-08-2009, 11:03 AM

Quote:

Originally Posted by Scott@FontanaNissan

Of course you would let me....wouldn't ya???

I would.

M.Bonanni · 07-08-2009, 11:43 AM

Just ordered an Unorthodox Racing stock diameter crank pulley! According to them, this will shed 7 lbs. of rotating mass off of the front of the car resulting in quicker revs, better throttle response, and more freed up horsepower. They are also claiming gains of 10-14 horsepower, but I am assuming that is at the crank, not at the wheels. We'll find out soon enough!

PM me for pricing and availability!

semtex · 07-08-2009, 01:07 PM

Quote:

Originally Posted by DDMotorsports

Just ordered an Unorthodox Racing stock diameter crank pulley! According to them, this will shed 7 lbs. of rotating mass off of the front of the car resulting in quicker revs, better throttle response, and more freed up horsepower. They are also claiming gains of 10-14 horsepower, but I am assuming that is at the crank, not at the wheels. We'll find out soon enough!

PM me for pricing and availability!

10-14 hp from a stock diameter pulley???

Even at the crank I'd be surprised if it made that much. I dyno'd the Stillen UD pulley at +5whp on a DynoJet. But like you said, we'll find out soon enough.

M.Bonanni · 07-08-2009, 01:59 PM

Quote:

Originally Posted by semtex

10-14 hp from a stock diameter pulley???

Even at the crank I'd be surprised if it made that much. I dyno'd the Stillen UD pulley at +5whp on a DynoJet. But like you said, we'll find out soon enough.

Yeah not too confident in their numbers either, but we'll see. I would expect gains to be in line with the Stillen pulley.

wstar · 07-08-2009, 02:19 PM

Quote:

Originally Posted by DDMotorsports

Yeah not too confident in their numbers either, but we'll see. I would expect gains to be in line with the Stillen pulley.

Except the Stillen one semtex dyno'd was underdriven, the unorthodox one isn't. Should be even less.

M.Bonanni · 07-08-2009, 02:20 PM

Quote:

Originally Posted by wstar

Except the Stillen one semtex dyno'd was underdriven, the unorthodox one isn't. Should be even less.

Not necessarily. It will depend on the weight of the Stillen vs. the weight of the Unorthodox.

semtex · 07-08-2009, 02:23 PM

But doesn't pulley diameter come into play as well? Smaller diameter = less power diverted to the auxiliary systems, right? I think that's what wstar is getting at.

M.Bonanni · 07-08-2009, 02:31 PM

Quote:

Originally Posted by semtex

But doesn't pulley diameter come into play as well? Smaller diameter = less power diverted to the auxiliary systems, right? I think that's what wstar is getting at.

Yeah it does also have effect but if its also heavier than the UR one then it will be a wash. Even if they weigh the same, I would guess that it will make 1whp difference max, or less. You will gain more from less weight than less parasitic drag. Like I said, we'll see once I put the UR pulley on my car. I personally prefer to use a stock diameter pulley to maintain factory accessory outputs from the alternator, power steering, etc.

07-07-2009, 06:06 PM	#377 (permalink)
M.Bonanni The370Z.com Sponsor Join Date: Nov 2008 Location: Las Vegas Posts: 2,575 Drives: Fast Rep Power: 1320	New set of Nitto NT05 tires showed up today! 275/35/18 front 285/35/18 rear. We'll see how the less staggered setup does August 1st & 2nd. We'll also find out if running a wider and stickier tire up front will uncover any more weaknesses with the car. Hopefully not, fingers crossed. My biggest concern to be quite honest is the SPC Camber arms either hitting the top of the wheel wells and/or not holding the alignment settings under hard load. __________________ MikeBonanni.com Twitter: http://www.twitter.com/MikeBonanni Facebook: http://www.facebook.com/MBonanni36 Function > Form

07-08-2009, 10:27 AM	#380 (permalink)
Scott@FontanaNissan Supporting Nissan Dealer Join Date: Jun 2009 Location: Fontucky, CA Posts: 857 Drives: 91 Sentra GTi-R Rep Power: 25	Hey Mike! so do you think maybe I can drive it??? __________________ Scott VanderHeide - Motorsports Director - Fontana Nissan/NissanRaceShop www.nissanraceshop.com www.youtube.com/scottvanderheide

07-08-2009, 11:01 AM	#382 (permalink)
Scott@FontanaNissan Supporting Nissan Dealer Join Date: Jun 2009 Location: Fontucky, CA Posts: 857 Drives: 91 Sentra GTi-R Rep Power: 25	Of course you would let me....wouldn't ya??? __________________ Scott VanderHeide - Motorsports Director - Fontana Nissan/NissanRaceShop www.nissanraceshop.com www.youtube.com/scottvanderheide

07-08-2009, 11:43 AM	#384 (permalink)
M.Bonanni The370Z.com Sponsor Join Date: Nov 2008 Location: Las Vegas Posts: 2,575 Drives: Fast Rep Power: 1320	Just ordered an Unorthodox Racing stock diameter crank pulley! According to them, this will shed 7 lbs. of rotating mass off of the front of the car resulting in quicker revs, better throttle response, and more freed up horsepower. They are also claiming gains of 10-14 horsepower, but I am assuming that is at the crank, not at the wheels. We'll find out soon enough! PM me for pricing and availability! __________________ MikeBonanni.com Twitter: http://www.twitter.com/MikeBonanni Facebook: http://www.facebook.com/MBonanni36 Function > Form

07-08-2009, 02:23 PM	#389 (permalink)
semtex A True Z Fanatic Join Date: Jan 2009 Location: Behind enemy lines Age: 53 Posts: 5,995 Drives: People to drink Rep Power: 32	But doesn't pulley diameter come into play as well? Smaller diameter = less power diverted to the auxiliary systems, right? I think that's what wstar is getting at. __________________ "There are no small accidents on this circuit." -- Ayrton Senna 316.8whp & 248 ft/lbs (Dyno Dynamics) \| 319whp & 256 ft/lbs (DynoJet) (04/23/10) Stillen G3 CAI, CBE, Pulley / F.I. LTH / GTSpec Ladder Brace / Setrab Oil Cooler / UpRev-tuned by Forged Perf.

07-07-2009, 04:55 PM	#376 (permalink)
Togo A True Z Fanatic Join Date: May 2009 Location: E. Northport, NY Posts: 7,597 Drives: Stuff Rep Power: 656	I wouldn't put it past misprint, which is why i only claimed that i thought i read they were those sizes. I thought it was odd though that they left the staggered for a non-staggered setup

07-08-2009, 06:49 AM	#378 (permalink)
miguez Enthusiast Member Join Date: Apr 2009 Location: Columbus, Ohio Posts: 359 Drives: '04 Cavalier Rep Power: 181	Mike, you should be able to check the wheel well for impact marks when you swap tires before this event, correct? Keep us posted!