AlWakRa 370z's Journal - PW from Qatar

AlWakRa · 12-15-2019, 03:58 AM

Stopped posting for sometime, I think 3 hard weeks, so finished the roll cage, I had to travel to Paris for 4 days and then returned to install the dashboard and finish all the remaining job to get the car in a working condition for the race, my target was to check if I have any technical requirement missing and to get the chance to have a shake down for the car.

The car had an exhaust leak, before the cats, which got wrong reading for the o2 sensors, so I think it was pulling a lot of timing, my car was maybe the slowest out there

and right axle boot broke, after inspection, it appears the ball joint nut snapped and with small bumps and play broke it. Made a quick fix, and entered first race to just see if there is more problems, I think I have over cooled the engine as it barely reach 92-93 while racing. The suspension setup was very safe, understeer and then turns with throttle, I didn't have the time to get alignment, I think it will make the car turns harder.

Didn't finish the race, hopefully next race it will be ready and finish both races.

I made a list for what to buy now, I will start with new full exhaust, front lower arm, high hp rated axles, and new bolts/nuts for the car.

Martijn_b · 12-25-2019, 09:25 AM

Once that you got to take it out on track. Its gonna be a bit trial and error probably for the first 2-3 times, but it should be fine after that! Enjoy!

Sent from my SM-G973F using Tapatalk

Zezus · 12-30-2019, 01:18 PM

Quote:

Originally Posted by AlWakRa

Stopped posting for sometime, I think 3 hard weeks, so finished the roll cage, I had to travel to Paris for 4 days and then returned to install the dashboard and finish all the remaining job to get the car in a working condition for the race, my target was to check if I have any technical requirement missing and to get the chance to have a shake down for the car.

The car had an exhaust leak, before the cats, which got wrong reading for the o2 sensors, so I think it was pulling a lot of timing, my car was maybe the slowest out there

and right axle boot broke, after inspection, it appears the ball joint nut snapped and with small bumps and play broke it. Made a quick fix, and entered first race to just see if there is more problems, I think I have over cooled the engine as it barely reach 92-93 while racing. The suspension setup was very safe, understeer and then turns with throttle, I didn't have the time to get alignment, I think it will make the car turns harder.

Didn't finish the race, hopefully next race it will be ready and finish both races.

I made a list for what to buy now, I will start with new full exhaust, front lower arm, high hp rated axles, and new bolts/nuts for the car.

Put KPro high up on your list of future upgrades. An increased rev limit and proper tune really bring the K20 to life.

AlWakRa · 01-05-2020, 07:27 PM

Quote:

Originally Posted by Zezus

Put KPro high up on your list of future upgrades. An increased rev limit and proper tune really bring the K20 to life.

Yeah, it is on my list, I talked to Steve@e-tunez about it, as two friends who are racing got their tune from him with good luck, in addition to more revs, making the vtec engage at 4k rpm would be very useful.

I am planning to get Hybrid Racing 3.5" CAI, 70mm TB, RRC IM, and tune. I already have big bore header and 3" catback on order from a shop called Solid Fabrications.

AlWakRa · 01-05-2020, 07:38 PM

Yeah, got the Z on track again, didn't video record laps, it was more of a track taxi

but I got some really nice photos, I tried a minor tweak to my usual alignment and I like it, front camber -2.94 with as much caster as I can get, 0.08 front toe out, rear -1.83 camber and 0.15 rear toe in. One of the people who got a ride with me, said I didn't thought a Nissan would have that much grip

Rusty · 01-05-2020, 08:39 PM

Hotrodz · 01-05-2020, 08:46 PM

The saying is...the more caster the faster you will be! Depending on camber mine is runs between 6 and 8. I use less caster the more camber I run and toe.

AlWakRa · 01-06-2020, 09:27 AM

I believe my caster at 5.5-6, this is the max, maybe because I am not that low, as I understand, more caster means more camber gain when you turn, it is very beneficial if you want a street/track car.

Hotrodz · 01-06-2020, 10:33 AM

Quote:

Originally Posted by AlWakRa

I believe my caster at 5.5-6, this is the max, maybe because I am not that low, as I understand, more caster means more camber gain when you turn, it is very beneficial if you want a street/track car.

6 is about where I keep mine when running -3.3 and still with a little toe. I was at 6.6 with pretty much your exact alignment.

Sent from my SM-G965U using Tapatalk

AlWakRa · 01-06-2020, 03:42 PM

I think my height is the limiting here, as MCA adviced me to return oem swaybars, so I had a little rubbing when I lowered the fronts, I will need to roll my fenders, also, I am planning to go for lower tires next time and get the car lower. I have two sets to finish right now, 275/40/18 sur4g and 285/30/18 r1s, after they are done, I am planning on trying 295/35/18 yoko a052, a lot of positive reviews about them.

I didn't know if I reported it, but I have some issues with my tranny, a little hard to get gears in and 5th grinds, the clutch engagement point isn't as smooth as it was, I think after two weeks I will have some time to get the transmission down and check clutch/pressure plate, if everything looked fine, I think I will be due for a new synchros or full tranny. It is still drivable but I need to be easy when shifting.

Hotrodz · 01-06-2020, 05:59 PM

Quote:

Originally Posted by AlWakRa

I think my height is the limiting here, as MCA adviced me to return oem swaybars, so I had a little rubbing when I lowered the fronts, I will need to roll my fenders, also, I am planning to go for lower tires next time and get the car lower. I have two sets to finish right now, 275/40/18 sur4g and 285/30/18 r1s, after they are done, I am planning on trying 295/35/18 yoko a052, a lot of positive reviews about them.

I didn't know if I reported it, but I have some issues with my tranny, a little hard to get gears in and 5th grinds, the clutch engagement point isn't as smooth as it was, I think after two weeks I will have some time to get the transmission down and check clutch/pressure plate, if everything looked fine, I think I will be due for a new synchros or full tranny. It is still drivable but I need to be easy when shifting.

Copy that! You are running much taller tires than I am. Running a smaller diameter tire will help. I am running 315 30 square so rubbing has not been an issue.

Sounds like your synchros are starting to go. I got to start saving for a tranny just in case!

Sent from my SM-G965U using Tapatalk

AlWakRa · 01-18-2020, 01:11 PM

Did an Autocross event today, my best run here

AlWakRa · 01-25-2020, 04:26 PM

The schedule is very tight for my RSX, before two weeks I missed a round, this weekend there was a round that I participated in, but still I have alignment issue and limp mode, my fastest lap was 2:37, hopefully I will sort out the power issue this week, but I am not looking into tuning until I can get a trackday to do the logs.

Here is my fastest

My car speed was third from last, but I finished 10th from 20 participants in both races. I hope for improvements in next race.

AlWakRa · 02-10-2020, 07:17 PM

After two years of hard use with OS Giken HTR2CD, decided it is time to go back to single plate clutch, ordered Zspeed Stage 3 with CMAK upgrade to v2.

OS experience was fantastic in track, good in street until you reach a traffic jam, it heats and starts to be an on off engagement, I wouldn't blame the kit as I got the second most aggressive model in their lineup

recently, the gear changes started to be hard, the feel is more like the clutch isn't disengaging quickly, and 5th grinds unless I go very very slowly in it. So, it is a great time to get the transmission down for inspection on syncros and change the clutch. Also, I plan to use the car in street more often, I choose a little aggressive kit, but it should be a lot better than OS in street and holds track abuse.

Waiting for it, it should shows up within two weeks.

After that I plan on doing some adjustment for autox, like getting my sway bars back on the car, changing my sur4g to r1s and getting the car lower (it should go pretty low with 285/30/18) with more aggressive alignment

as my current one isn't aggressive

Did one Autocross event with the Z, unfortunately didn't get my fastest run recorded, this was an experiment to use 1st gear in the narrow layout, which was slower than my fastest by more than a second.

Also, participated in another race with my rsx, only mod was to change the exhaust and manifold, which didn't get the check engine off for secondary O2 sensor, and I get rear bushes installed and new bolts for camber and toe. Had a better alignment Front -3 camber 0.08 toe out (3 caster which isn't adjustable) Rear -1.8 camber 0 toe. It rotates better now but still understeers, but this time felt the lack of power, so kpro4 is on top of my list.

I have my plans set for now, I will get my boltons completed, which I already mentioned before, IM, CAI, 70mm TB, and tune. For suspension, I will try to get new front top mounts to increase caster, I may reduce rear camber a little, also, I may get a strut braces for rear side, which should help the car to rotate better.

AlWakRa · 02-18-2020, 02:08 PM

The new clutch and flywheel from Zspeed, Super Street kit with Cmak v2 conversion to the one I have already. Kudos to Joe for the great service and communication.

12-15-2019, 03:58 AM	#241 (permalink)
AlWakRa Track Member Join Date: Oct 2010 Location: Qatar Posts: 600 Drives: 10 370Z PW 6MT Rep Power: 13450	Stopped posting for sometime, I think 3 hard weeks, so finished the roll cage, I had to travel to Paris for 4 days and then returned to install the dashboard and finish all the remaining job to get the car in a working condition for the race, my target was to check if I have any technical requirement missing and to get the chance to have a shake down for the car. The car had an exhaust leak, before the cats, which got wrong reading for the o2 sensors, so I think it was pulling a lot of timing, my car was maybe the slowest out there and right axle boot broke, after inspection, it appears the ball joint nut snapped and with small bumps and play broke it. Made a quick fix, and entered first race to just see if there is more problems, I think I have over cooled the engine as it barely reach 92-93 while racing. The suspension setup was very safe, understeer and then turns with throttle, I didn't have the time to get alignment, I think it will make the car turns harder. Didn't finish the race, hopefully next race it will be ready and finish both races. I made a list for what to buy now, I will start with new full exhaust, front lower arm, high hp rated axles, and new bolts/nuts for the car. Rusty, Hotrodz, madwi and 3 others like this. __________________ 2010 370Z Touring Sport Pearl White 6MT Powered by: Fast Intentions - Motordyne - Stillen - OS Giken - CJ Motorsports - Mishimoto - MCA Suspension - SPL - SuperPRO - RJM - Z1 Motorsport - Zspeed - Volk My Humble Journals

12-25-2019, 09:25 AM	#242 (permalink)
Martijn_b Enthusiast Member Join Date: Jan 2018 Location: Netherlands Posts: 280 Drives: 2010 370z MB 6MT Rep Power: 3786	Once that you got to take it out on track. Its gonna be a bit trial and error probably for the first 2-3 times, but it should be fine after that! Enjoy! Sent from my SM-G973F using Tapatalk AlWakRa, Rusty and Hotrodz like this. __________________ Instagram: Boosted_Fairlady

01-05-2020, 08:39 PM	#246 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 68 Posts: 35,157 Drives: 2011 Nismo GM 6M Rep Power: 2684437	AlWakRa likes this. __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

01-05-2020, 08:46 PM	#247 (permalink)
Hotrodz A True Z Fanatic Join Date: Aug 2012 Location: NW, AZ Posts: 9,330 Drives: 10 Nissan 370z Nismo Rep Power: 2684385	The saying is...the more caster the faster you will be! Depending on camber mine is runs between 6 and 8. I use less caster the more camber I run and toe. AlWakRa likes this. __________________ *Fast Intentions TT Installed and Tuned by Seb at SpecialtyZ 610whp 560tq:\|Fast Intentions 3" TT-TDX*\|SpecialtyZ/Fast Intentions 72 Row Oil Cooler\|SZ 6 Puck Clutch & Flywheel\|3GsCustoms\|Z1\|Wavetrac\|Hotchkis\|Whiteline \|Blitz\|Fortune Auto 500\|Fujimura\|SPL\|H&R\|TK\|TWM\|RPM Rollbar\|Sparco\|Next Level Performance\|TrackSpec\|AeroFlow Dynamics\|Pioneer\|

01-06-2020, 09:27 AM	#248 (permalink)
AlWakRa Track Member Join Date: Oct 2010 Location: Qatar Posts: 600 Drives: 10 370Z PW 6MT Rep Power: 13450	I believe my caster at 5.5-6, this is the max, maybe because I am not that low, as I understand, more caster means more camber gain when you turn, it is very beneficial if you want a street/track car. Hotrodz likes this. __________________ 2010 370Z Touring Sport Pearl White 6MT Powered by: Fast Intentions - Motordyne - Stillen - OS Giken - CJ Motorsports - Mishimoto - MCA Suspension - SPL - SuperPRO - RJM - Z1 Motorsport - Zspeed - Volk My Humble Journals

01-06-2020, 03:42 PM	#250 (permalink)
AlWakRa Track Member Join Date: Oct 2010 Location: Qatar Posts: 600 Drives: 10 370Z PW 6MT Rep Power: 13450	I think my height is the limiting here, as MCA adviced me to return oem swaybars, so I had a little rubbing when I lowered the fronts, I will need to roll my fenders, also, I am planning to go for lower tires next time and get the car lower. I have two sets to finish right now, 275/40/18 sur4g and 285/30/18 r1s, after they are done, I am planning on trying 295/35/18 yoko a052, a lot of positive reviews about them. I didn't know if I reported it, but I have some issues with my tranny, a little hard to get gears in and 5th grinds, the clutch engagement point isn't as smooth as it was, I think after two weeks I will have some time to get the transmission down and check clutch/pressure plate, if everything looked fine, I think I will be due for a new synchros or full tranny. It is still drivable but I need to be easy when shifting. Rusty, Hotrodz and BettyZ like this. __________________ 2010 370Z Touring Sport Pearl White 6MT Powered by: Fast Intentions - Motordyne - Stillen - OS Giken - CJ Motorsports - Mishimoto - MCA Suspension - SPL - SuperPRO - RJM - Z1 Motorsport - Zspeed - Volk My Humble Journals

01-18-2020, 01:11 PM	#252 (permalink)
AlWakRa Track Member Join Date: Oct 2010 Location: Qatar Posts: 600 Drives: 10 370Z PW 6MT Rep Power: 13450	Did an Autocross event today, my best run here gbrettin, Rusty, Hotrodz and 4 others like this. __________________ 2010 370Z Touring Sport Pearl White 6MT Powered by: Fast Intentions - Motordyne - Stillen - OS Giken - CJ Motorsports - Mishimoto - MCA Suspension - SPL - SuperPRO - RJM - Z1 Motorsport - Zspeed - Volk My Humble Journals

01-25-2020, 04:26 PM	#253 (permalink)
AlWakRa Track Member Join Date: Oct 2010 Location: Qatar Posts: 600 Drives: 10 370Z PW 6MT Rep Power: 13450	The schedule is very tight for my RSX, before two weeks I missed a round, this weekend there was a round that I participated in, but still I have alignment issue and limp mode, my fastest lap was 2:37, hopefully I will sort out the power issue this week, but I am not looking into tuning until I can get a trackday to do the logs. Here is my fastest My car speed was third from last, but I finished 10th from 20 participants in both races. I hope for improvements in next race. Rusty, Hotrodz, madwi and 1 others like this. __________________ 2010 370Z Touring Sport Pearl White 6MT Powered by: Fast Intentions - Motordyne - Stillen - OS Giken - CJ Motorsports - Mishimoto - MCA Suspension - SPL - SuperPRO - RJM - Z1 Motorsport - Zspeed - Volk My Humble Journals

02-10-2020, 07:17 PM	#254 (permalink)
AlWakRa Track Member Join Date: Oct 2010 Location: Qatar Posts: 600 Drives: 10 370Z PW 6MT Rep Power: 13450	After two years of hard use with OS Giken HTR2CD, decided it is time to go back to single plate clutch, ordered Zspeed Stage 3 with CMAK upgrade to v2. OS experience was fantastic in track, good in street until you reach a traffic jam, it heats and starts to be an on off engagement, I wouldn't blame the kit as I got the second most aggressive model in their lineup recently, the gear changes started to be hard, the feel is more like the clutch isn't disengaging quickly, and 5th grinds unless I go very very slowly in it. So, it is a great time to get the transmission down for inspection on syncros and change the clutch. Also, I plan to use the car in street more often, I choose a little aggressive kit, but it should be a lot better than OS in street and holds track abuse. Waiting for it, it should shows up within two weeks. After that I plan on doing some adjustment for autox, like getting my sway bars back on the car, changing my sur4g to r1s and getting the car lower (it should go pretty low with 285/30/18) with more aggressive alignment as my current one isn't aggressive Did one Autocross event with the Z, unfortunately didn't get my fastest run recorded, this was an experiment to use 1st gear in the narrow layout, which was slower than my fastest by more than a second. Also, participated in another race with my rsx, only mod was to change the exhaust and manifold, which didn't get the check engine off for secondary O2 sensor, and I get rear bushes installed and new bolts for camber and toe. Had a better alignment Front -3 camber 0.08 toe out (3 caster which isn't adjustable) Rear -1.8 camber 0 toe. It rotates better now but still understeers, but this time felt the lack of power, so kpro4 is on top of my list. I have my plans set for now, I will get my boltons completed, which I already mentioned before, IM, CAI, 70mm TB, and tune. For suspension, I will try to get new front top mounts to increase caster, I may reduce rear camber a little, also, I may get a strut braces for rear side, which should help the car to rotate better. Hotrodz, madwi and ZontheRocks like this. __________________ 2010 370Z Touring Sport Pearl White 6MT Powered by: Fast Intentions - Motordyne - Stillen - OS Giken - CJ Motorsports - Mishimoto - MCA Suspension - SPL - SuperPRO - RJM - Z1 Motorsport - Zspeed - Volk My Humble Journals

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Where are all you 370Z's at?	BOLIO 671	Hawaii	7	06-21-2010 04:40 AM
Where Have All the 370Z's Gone and Where Will All the 370Z's Go?	LinPark	Nissan 370Z General Discussions	47	04-02-2010 01:56 AM
370z's	Majestik	Australia/New Zealand	0	03-06-2010 02:49 AM
First member from Qatar!	TomatoEvo	New Forum Member	9	01-09-2009 06:25 AM