New Soho Single exit for the 370z!!

TheBoomSpoon · 02-14-2015, 11:52 PM

Ok i sent you a private msg with my email.

Thx

Gregor12 · 02-16-2015, 01:17 AM

Does anyone in here live near charlotte? looking for a stock 370z to put on that dyno to see what kind of numbers it reads. I dont feel like putting my stock **** back on lol ill pay for three dyno pulls on your BONE STOCK Z

synolimit · 02-16-2015, 04:45 AM

Wonder about that dyno's age. Sounded like 4th gear so you're not reading higher than others that use 5th (we should all use 5th) but that run took a long time! I only use SAE but to calculate my STD I'm doing 321hp. my run takes 9 seconds, yours took 12. Something tells me someones dyno is way off cause 3 seconds on the street just to redline 4th would be a massacre. No offense here.

synolimit · 02-16-2015, 04:50 AM

Quote:

Originally Posted by Japanjay

I cant find this website you speak of but I can show a picture of one on a 370z and if you look it has "2" pipes that mate to a F/I exhaust. I think you are looking at the kits for the DE's which do in fact use a single exhaust pipe..... I really hate going to this extent, especially since I spoke with sasha and the "pictures" are readily available on the internet if you just search. Now once you study these pictures, explain to me how this looks like it bolts to a factory exhaust, meaning that a single will work, and post the link where you found that it specifically states that it will work with factory. I could even go as far as posting this in ALL CAPS AS WELL TO GET THE POINT ACROSSSSSS!!!! I even drew in red arrows to clearly point to the 2 flanges, before those 2 flanges the driver side pipe catches the resurq from the wastegate, then the 2 pipes merge into one, which comes from the hot side of the turbine housing....

Unless you find another exhaust that has the IDENTICAL FLANGE DESIGN AND PLACEMENT YOU WONT JUST BE ABLE TO BOLT A BP KIT UP TO YOUR EXHAUST WITHOUT MODIFICATION. Which can be done and I would recommend it be done to the exhaust not the kit or it will make it a tough resale when you part out.... Just sayin

.

synolimit · 02-16-2015, 04:58 AM

Quote:

Originally Posted by Gregor12

my car made the 298 (4th) with just the exhaust and no tune. stock y pipe, stock cats and stock intakes.

Quote:

Originally Posted by Gregor12

made 320rwhp and 270lb/ft with the stock intakes, stock cats, and factory tune!

Wait I'm so confused now.

Gregor12 · 02-16-2015, 12:48 PM

Quote:

Originally Posted by Scott@Synergy

Wonder about that dyno's age. Sounded like 4th gear so you're not reading higher than others that use 5th (we should all use 5th) but that run took a long time! I only use SAE but to calculate my STD I'm doing 321hp. my run takes 9 seconds, yours took 12. Something tells me someones dyno is way off cause 3 seconds on the street just to redline 4th would be a massacre. No offense here.

hey scott, let me clear things up haha i know this thread has turned into a cluster ****
First mod i purchased from soho motosports a while back was their rear section of the catback exhaust which uses the factory y-pipe. The first pull we did when it had no tune (factory) was in 4th gear (just to do a small pull then tighten down the straps again before fifth)

-it made 299.45rwhp and 24X lbft in 4th gear

Last week, I bought and installed their y-pipe replacing the factory POS y-pipe. strapped it down and did a 4th gear pull to compare to my last 4th gear pull. (this was a stock tune comparison)

- with y-pipe and y-back exhaust it made 313.4rwhp and 258.4lb/ft in 4th gear

So after that, nick did 3 5th gear pulls since 5th is 1:1. The video I posted was the last 5th gear pull we did of the day.

- with the exhaust and factory tune it made 320.46 rwhp and 269.09 lb ft (5th gear)

let me know if you have any other questions. as for the dyno being off I really don’t think so. they’ve had 3 annual dyno days there and nobody was reading high comparing to their previous dyno tunes.

ill ask nick for SAE numbers as well for a comparison. and SOMEONE FIND ME A STOCK Z lol

Gregor12 · 02-16-2015, 12:52 PM

this is what i made 299 with in 4th gear

then i added this piece and made 313 in 4th gear and 320 in 5th

synolimit · 02-16-2015, 01:34 PM

Quote:

Originally Posted by Gregor12

- with the exhaust and factory tune it made 320.46 rwhp and 269.09 lb ft (5th gear)

as for the dyno being off I really don’t think so. they’ve had 3 annual dyno days there and nobody was reading high comparing to their previous dyno tunes.

I counted 3 gear changes before WOT but if he was in 2nd then no I don't think anythings off. Also explains the 12 second run.

NoLaKrewe · 02-16-2015, 08:20 PM

What soho exhaust do they make that works with turbos

Gregor12 · 02-16-2015, 09:06 PM

Quote:

Originally Posted by NoLaKrewe

What soho exhaust do they make that works with turbos

i believe most of their cars run a full catless 3 inch. on davids 8XX rwhp G horsepower they’re using a full 3.5 inch. I dont work for soho or anything they’re just a local shop that has always done the work for me, my family, and friends. They’re stand up guys

Gregor12 · 02-16-2015, 09:08 PM

Quote:

Originally Posted by Scott@Synergy

I counted 3 gear changes before WOT but if he was in 2nd then no I don't think anythings off. Also explains the 12 second run.

just noticed that lol and yes he was in 2nd. I started the camera right after he switched gears. ill be sure to get you guys a baseline. i know soho wants one to so they can compare

Joepro · 02-16-2015, 10:51 PM

The only thing that matters is the difference between runs with the different parts, but its true the setup on the dyno means a lot, as well as the correction weather etc...A true comparison would have been on the same day...so IMO that dyno reads high, but it does not really matter, congrats for breaking 320 whp for that amount of cash, took me a lot more and a tune from one of the best in the biz!

Gregor12 · 02-16-2015, 11:16 PM

Quote:

Originally Posted by Joepro

The only thing that matters is the difference between runs with the different parts, but its true the setup on the dyno means a lot, as well as the correction weather etc...A true comparison would have been on the same day...so IMO that dyno reads high, but it does not really matter, congrats for breaking 320 whp for that amount of cash, took me a lot more and a tune from one of the best in the biz!

thanks Joe, i will do a baseline with my car and a stock Z on another day at the same time. I will settle this once and for all. no one else is running a single 3 inch exhaust so it may just be that it makes more power than a dual set up with 6 bends in it lol

heres a Z that made 312 with just a cat back I’m only 8hp above that
https://www.youtube.com/watch?v=ETDnW2tLows

NoLaKrewe · 02-17-2015, 08:39 PM

Couple noob questions..

Can I get some pictures of the clearance in the rear? I know Tomei hangs low.

If I grab a Y Pipe and this catback, what's left with the exhaust to modify?

Is their any kits for the Z that has a single exit for the back? I was thinking this won't look bad with amuse.

Gregor12 · 02-17-2015, 09:31 PM

Quote:

Originally Posted by NoLaKrewe

Couple noob questions..

Can I get some pictures of the clearance in the rear? I know Tomei hangs low.

If I grab a Y Pipe and this catback, what's left with the exhaust to modify?

Is their any kits for the Z that has a single exit for the back? I was thinking this won't look bad with amuse.

NoLaKrewe,

as for clearance i think you’ll be fine. its tucked up very well and probably has the same amount of clearance as the factory exhaust.

Only thing left to modify or change would be the test pipes and headers. or you could just buy the rear section that bolts to the factory y-pipe if you’re just looking for sound or looks.

when it comes to kits I’m not sure whats out there. the amuse doesn’t have cutouts so i dont think it would look bad. Good luck sir!

Phil

02-16-2015, 01:17 AM	#107 (permalink)
Gregor12 Enthusiast Member Join Date: Oct 2013 Location: CHARLOTTE, NC Posts: 433 Drives: 2012 370z 6mt sport Rep Power: 12	Does anyone in here live near charlotte? looking for a stock 370z to put on that dyno to see what kind of numbers it reads. I dont feel like putting my stock **** back on lol ill pay for three dyno pulls on your BONE STOCK Z YzGyz likes this.

02-16-2015, 04:45 AM	#108 (permalink)
synolimit A True Z Fanatic Join Date: May 2013 Location: Columbus, OH Posts: 5,051 Drives: 2013 Silver 370z Rep Power: 3390	Wonder about that dyno's age. Sounded like 4th gear so you're not reading higher than others that use 5th (we should all use 5th) but that run took a long time! I only use SAE but to calculate my STD I'm doing 321hp. my run takes 9 seconds, yours took 12. Something tells me someones dyno is way off cause 3 seconds on the street just to redline 4th would be a massacre. No offense here. __________________ 13 370z-

02-16-2015, 12:52 PM	#112 (permalink)
Gregor12 Enthusiast Member Join Date: Oct 2013 Location: CHARLOTTE, NC Posts: 433 Drives: 2012 370z 6mt sport Rep Power: 12	this is what i made 299 with in 4th gear then i added this piece and made 313 in 4th gear and 320 in 5th synolimit likes this.

02-16-2015, 08:20 PM	#114 (permalink)
NoLaKrewe Enthusiast Member Join Date: Jun 2014 Location: NoLa Posts: 469 Drives: 2011 FJ//2015 370z Rep Power: 13	What soho exhaust do they make that works with turbos __________________ Starting a NoLa Z club https://www.facebook.com/groups/TheBigeZClub/ The struggle will be real!

02-16-2015, 10:51 PM	#117 (permalink)
Joepro A True Z Fanatic Join Date: Aug 2012 Location: Athens ohio Posts: 1,213 Drives: Company car Rep Power: 34	The only thing that matters is the difference between runs with the different parts, but its true the setup on the dyno means a lot, as well as the correction weather etc...A true comparison would have been on the same day...so IMO that dyno reads high, but it does not really matter, congrats for breaking 320 whp for that amount of cash, took me a lot more and a tune from one of the best in the biz! __________________ Swift\|Koni\|SPC\| FI CBE\|Z1\|Stillen\|Sbend\|Zspeed\|R/T Tuned\|523 whp\|458 tq\|10.5 psi\|SOLD Joepro's Journal\|Joepro's Boosted Performance Build \|Pittsburgh-Western-Pa-Ohio-Wv-Group

02-14-2015, 11:52 PM	#106 (permalink)
TheBoomSpoon Base Member Join Date: Feb 2014 Location: Charlotte, NC Posts: 223 Drives: 2009 370z 7at Rep Power: 12	Ok i sent you a private msg with my email. Thx

02-17-2015, 08:39 PM	#119 (permalink)
NoLaKrewe Enthusiast Member Join Date: Jun 2014 Location: NoLa Posts: 469 Drives: 2011 FJ//2015 370z Rep Power: 13	Couple noob questions.. Can I get some pictures of the clearance in the rear? I know Tomei hangs low. If I grab a Y Pipe and this catback, what's left with the exhaust to modify? Is their any kits for the Z that has a single exit for the back? I was thinking this won't look bad with amuse. __________________ Starting a NoLa Z club https://www.facebook.com/groups/TheBigeZClub/ The struggle will be real!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
3inch single exit exhaust too big for N/A	blacknismoZ	Intake/Exhaust	63	01-27-2016 01:16 PM
New Custom Exhaust Single Exit 3.5''	Megan370z	Intake/Exhaust	28	09-30-2013 08:05 PM
370z Nismo Single exit	1SlowNizzy	Member's 370Z Gallery	30	08-22-2013 03:18 AM
AMUSE R1000 single exit exhaust review	VancouverZ34	Canada	33	03-02-2012 12:44 AM
Single Exit Exhaust	JDW1479	Intake/Exhaust	4	10-26-2010 12:22 AM