Custom ported and CNC throttle bodies, upper and lower manifolds by Synergy Composite

jrb55gh · 12-28-2014, 10:21 PM

Quote:

Originally Posted by Scott@Synergy

That's the tuners call to post that. I'm not sure what was done but from days beginning till days end we targeted and achieved pretty much 12.5 the whole time. All I know 100% is the cars timing is WAY down vs what mine and others are. This again doesn't affect all you as the car still made good power but something's up!

If I'd of known better about the owners 08 80,000 miles g37 7at with HFCs id of never picked him as a test car. I wanted a 6mt catless but I'm committed to him now.

I read your whole thread. Getting verifiable results to prove your concept with minimal investment is a tough assignment. But you did it. Thanks for all seeing it through to a usable conclusion.

I compared your 23 degree timing with the datalog on my stock 2013 7AT with ECUtek tune and noticed that my max timing at full throttle is 29 degrees. That timing does not knock on my stock 370 with clean combustion chambers. The reduced 23 degree timing required for your 80k mile test vehicle may be the result of deposits in the combustion chamber causing hot spots and/or raising the compression ratio.

Somewhere in the thread you mentioned verifying flow through the manifolds on a flow bench. That is a great idea. Some cylinders may be receiving more flow than others, running leaner and knocking. If you can adjust the porting to make the flow equal to all cylinders, you may be able to crank in more timing and unlock more power.

Zoren 370 · 12-29-2014, 06:39 AM

Sub

synolimit · 12-29-2014, 11:27 AM

Quote:

Originally Posted by jrb55gh

I read your whole thread. Getting verifiable results to prove your concept with minimal investment is a tough assignment. But you did it. Thanks for all seeing it through to a usable conclusion.

I compared your 23 degree timing with the datalog on my stock 2013 7AT with ECUtek tune and noticed that my max timing at full throttle is 29 degrees. That timing does not knock on my stock 370 with clean combustion chambers. The reduced 23 degree timing required for your 80k mile test vehicle may be the result of deposits in the combustion chamber causing hot spots and/or raising the compression ratio.

Somewhere in the thread you mentioned verifying flow through the manifolds on a flow bench. That is a great idea. Some cylinders may be receiving more flow than others, running leaner and knocking. If you can adjust the porting to make the flow equal to all cylinders, you may be able to crank in more timing and unlock more power.

That's a good point. If I'd of known more about the testers car I wouldn't have picked him. To much away from what I wanted.

The flow bench testing is done. I'll find out all of the info soon and maybe have Shawn chime in and talk about it.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Custom ported and CNC throttle bodies, upper and lower manifolds	synolimit	Exhaust/Intake	297	06-25-2021 09:13 AM
[WTB] Lower intake manifolds! Uppers and TB's welcome!!	synolimit	Parts for sale (Private Classifieds)	0	11-19-2014 02:02 AM
Smokeys dyno, ported TB's, manifolds etc	synolimit	Tuning	8	08-15-2014 11:11 AM
can the throttle bodies be taken off?	boomboom	Engine & Drivetrain	9	11-03-2013 01:46 PM
Kinetix 370Z/G37 Velocity Upper Intake Manifolds - Z1 Motorsports	Dustin@Z1	Intake/Exhaust	151	03-18-2013 09:37 AM

12-29-2014, 06:39 AM	#2 (permalink)
Zoren 370 A True Z Fanatic Join Date: Mar 2012 Location: FL Posts: 11,018 Drives: 11 Nissan 370 M6 Rep Power: 1913655	Sub