I have a problem with my intakes.

Trips · 01-04-2014, 02:17 PM

Mine broke off, and so I carefully removed the piece stuck on the hose and the filter from the other hose that its attached to

And got "Krazy Glue" to glue them together and once it was dry I very carefully installed it back on.

This way at least can buy you time to either find one used or order the hose with that part.

I honestly think its BS that they DONT sell that part by itself if that the case.

BTW mine has been broken for over a year

CWofRR · 01-06-2014, 01:35 PM

Thanks for your help. Appreciate it.

CWofRR · 01-06-2014, 01:51 PM

Quote:

Originally Posted by Trips

Mine broke off, and so I carefully removed the piece stuck on the hose and the filter from the other hose that its attached to

And got "Krazy Glue" to glue them together and once it was dry I very carefully installed it back on.

This way at least can buy you time to either find one used or order the hose with that part.

I honestly think its BS that they DONT sell that part by itself if that the case.

BTW mine has been broken for over a year

My friend at Nissan told me I had to buy the tube in order to get that piece. So that means I gotta shell out $150 for the right side of the intake. I gotta get the tube in order to get the piece.

Rangerz · 01-07-2014, 12:47 AM

Quote:

Originally Posted by CWofRR

My friend at Nissan told me I had to buy the tube in order to get that piece. So that means I gotta shell out $150 for the right side of the intake. I gotta get the tube in order to get the piece.

Those are intake resonators and you can take them off completely. I took mine off when I installed my Gen 3's you will notice a bit deeper exhaust note at least I did with the stillens. As mentioned above you still will need to route the breather hose back up to the stock intake hoses or get the filters.

PM Me if you want to keep it stock I have mine sitting in the garage.

synolimit · 01-09-2014, 02:39 AM

Quote:

Originally Posted by LostSol

Or you can replace those with these: Z1 Silicone Side PCV Breather Hose set for Aftermarket Intakes

That site says only for aftermarket intakes. I'm guessing this is because the OEM accordion hose has a female hole and aftermarket intakes have a male nipple welded on. If the OP has a OEM intake he will need a sleeve or connector to go into the OEM accordion hose and into the new Z1 hose

Quote:

Originally Posted by luigi90210

i just deleted those pieces for my intake install

just buy some rubber hose from autozone or something, its dirt cheap to get

The OEM piece is a restrictor. You're not getting any weird issues? I'd love to see a log or oil catch can or something that that restrictors supposed to restrict.

Quote:

Originally Posted by Rangerz

Those are intake resonators and you can take them off completely. I took mine off when I installed my Gen 3's you will notice a bit deeper exhaust note at least I did with the stillens. As mentioned above you still will need to route the breather hose back up to the stock intake hoses or get the filters.

PM Me if you want to keep it stock I have mine sitting in the garage.

Resonators or restrictors?

OP, since you broke yours, can you cut it open? I'd like to see inside.

Jordo! · 01-09-2014, 02:59 AM

Quote:

Originally Posted by synolimit

That site says only for aftermarket intakes. I'm guessing this is because the OEM accordion hose has a female hole and aftermarket intakes have a male nipple welded on. If the OP has a OEM intake he will need a sleeve or connector to go into the OEM accordion hose and into the new Z1 hose

The OEM piece is a restrictor. You're not getting any weird issues? I'd love to see a log or oil catch can or something that that restrictors supposed to restrict.

Resonators or restrictors?

OP, since you broke yours, can you cut it open? I'd like to see inside.

I had one break on me on my 1st 370Z. It's hollow -- just a right angle breather tube -- nothing special. If it cracks you get a vacuum leak, which is bad. That replacement breather tube from autozone does the trick.

synolimit · 01-09-2014, 03:15 AM

Quote:

Originally Posted by Jordo!

I had one break on me on my 1st 370Z. It's hollow -- just a right angle breather tube -- nothing special. If it cracks you get a vacuum leak, which is bad. That replacement breather tube from autozone does the trick.

Interesting. So what the hell is inside the Z1 hose?

Jordo! · 01-09-2014, 03:44 AM

Quote:

Originally Posted by synolimit

Interesting. So what the hell is inside the Z1 hose?

If its routed in the same locations -- I'm guessing nothing. Its probably just a flexible tube that runs between the IM port and the rubber intake tube.

CWofRR · 01-09-2014, 04:47 PM

Quote:

Originally Posted by synolimit

That site says only for aftermarket intakes. I'm guessing this is because the OEM accordion hose has a female hole and aftermarket intakes have a male nipple welded on. If the OP has a OEM intake he will need a sleeve or connector to go into the OEM accordion hose and into the new Z1 hose

The OEM piece is a restrictor. You're not getting any weird issues? I'd love to see a log or oil catch can or something that that restrictors supposed to restrict.

Resonators or restrictors?

OP, since you broke yours, can you cut it open? I'd like to see inside.

I have aftermarket intakes, they are Fujita from a g37. So they didn't fit 100% to begin with, but from what I'm reading the Z'1s should do the trick. Thanks for the help guys, appreciate it!

CWofRR · 01-09-2014, 04:53 PM

Did you want me to cut open the rectangular box? ( i dont exactly know what its called, so im just gonna call it that lol )

01-04-2014, 02:17 PM	#1 (permalink)
Trips Administrator Join Date: May 2009 Location: Disneyland, Ca Posts: 8,736 Drives: 🔰 Rep Power: 10	Mine broke off, and so I carefully removed the piece stuck on the hose and the filter from the other hose that its attached to And got "Krazy Glue" to glue them together and once it was dry I very carefully installed it back on. This way at least can buy you time to either find one used or order the hose with that part. I honestly think its BS that they DONT sell that part by itself if that the case. BTW mine has been broken for over a year __________________

01-06-2014, 01:35 PM	#2 (permalink)
CWofRR Base Member Join Date: Mar 2010 Location: Cali Posts: 116 Drives: herra slow Rep Power: 17	Thanks for your help. Appreciate it. __________________ IG impwks_wes

01-09-2014, 04:53 PM	#10 (permalink)
CWofRR Base Member Join Date: Mar 2010 Location: Cali Posts: 116 Drives: herra slow Rep Power: 17	Did you want me to cut open the rectangular box? ( i dont exactly know what its called, so im just gonna call it that lol ) __________________ IG impwks_wes

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
intakes	Csprad12	Intake/Exhaust	12	09-21-2013 12:49 PM
[FOR SALE] AEM Long Tube Intakes - Electronicaly Tuned Intakes (ETI), Gun Metal Powder Coated	FlawlessZ	Parts for sale (Private Classifieds)	24	02-15-2013 04:38 PM
WTB: Stillen G3 Intakes or K&N Typhoon intakes!	gromano	Parts for sale (Private Classifieds)	5	07-15-2010 08:38 PM
New Roadster, Spoiler problem, dealer problem	Hello	Nissan 370Z General Discussions	26	01-11-2010 05:22 PM
injen cold air intakes! or still G3 intakes? wich is better	fg2rick	Intake/Exhaust	10	12-08-2009 02:49 PM