Berk Test Pipe install...*^$#ing factory bolts!!!

98intrigue · 09-10-2010, 08:44 PM

My car was cold and I left the lubricant on the bolts for a good 2 hours before trying to break them off.

Holliday · 09-11-2010, 12:59 AM

Quote:

Originally Posted by 98intrigue

My car was cold and I left the lubricant on the bolts for a good 2 hours before trying to break them off.

me too!

Neo187H · 09-11-2010, 11:27 AM

Quote:

Originally Posted by tjlazer

Um no, it was a bloody battle but in the end I have HFC's on the car.

At the cost of a $700ish cat, I'd say the car took at least one point.

Kroil works some magic with seized up fasteners.

tjlazer · 09-11-2010, 11:43 AM

Quote:

Originally Posted by Neo187H

At the cost of a $700ish cat, I'd say the car took at least one point.

Kroil works some magic with seized up fasteners.

Well I never really thought I could sell them for anywhere that much, the best I was planning on doing is either keeping them or scrapping them for some ca$h at a metal recycle yard. ($80 for the set) which I just plan on doing that since one is toast. All they want is the precious metals in the cat anyway...)

mjohn617 · 09-12-2010, 11:32 AM

Quote:

Originally Posted by Elia Cid

mjohn617,

Your going to love the Stillen CBE,sound!

let's us know how they sound and you like them when your all done!

Thanks,
Alex

Definitally will do, I saw a clip on YouTube with same setup and the sound is unbelievable. I love that American throat, small block sound, this exhaust has a small hint of that. The exhaust notes that come out on decal are crazy! Stillen takes the win in my book.

The test pipes really opened up the bottom end, my wife even came home asking what I did to the car. I'm really curious to see what a dyno would show. Plus I'm getting 23MPG.

Urbanracer · 09-12-2010, 06:07 PM

I made it halfway through the installled getting the passender side installed but ended up letting a shop do the drivers side for me. I decided to stop while I was ahead and not distroy the drivers side "b*tch bolt" during my attempt. I noticed a bit of a rattle or leak though when the engine is reved, anyone else experience this? I'm planning on checking the gaskets over when I get time.

Holliday · 09-12-2010, 10:17 PM

Quote:

Originally Posted by Urbanracer

I made it halfway through the installled getting the passender side installed but ended up letting a shop do the drivers side for me. I decided to stop while I was ahead and not distroy the drivers side "b*tch bolt" during my attempt. I noticed a bit of a rattle or leak though when the engine is reved, anyone else experience this? I'm planning on checking the gaskets over when I get time.

I would definitely check for leaks if you have not already. But if you hear a hiss after acceleration it is normal with these cats for some reason. Good luck

Joseph B · 09-13-2010, 01:02 PM

Removal of the cats on our Z isn't for the faint of heart. It took me about two hours (including jacking it up and down), You have to work slowly, make sure you use a nice penetrant (3m), and have lots of extensions. I used 3/8 and they worked fine. Yes, never use 12 point sockets on something so stubborn, you will strip it. You do NOT need an impact gun for this, probably best you don't use one at all on the exhuast.

I feel bad for those that destroyed their cats trying to get them off, what a nightmare. Hope you never need your cats back on.

tjlazer · 09-13-2010, 01:13 PM

Quote:

Originally Posted by Joseph B

I feel bad for those that destroyed their cats trying to get them off, what a nightmare. Hope you never need your cats back on.

It was a nightmare as at one point I was like screw it. I was about ready to put it all back together and limp it to the nearest Midas. But I was running out of time and this was this only alternative. I was going to win damn it!!! I had stripped out the nut so there was no turning back. Stock cats are not going back, ever.

370Zsteve · 09-13-2010, 01:13 PM

This thread is full of win, lol. Except for you TJ, I have to give the point to the car, man.

tjlazer · 09-13-2010, 01:26 PM

Quote:

Originally Posted by 370Zsteve

This thread is full of win, lol. Except for you TJ, I have to give the point to the car, man.

Hahah well I was beat on hard I agree. But in the end I will be driving said Z with HFC's down to the metal recycle yard to cash in on my stock cats for some cash...

It's no surprise to me at all actually. I had a bad feeling it was going to be an EPIC fail moment for me. It always is with me. Whenever I do all my mods I take the stated install times and multiply by 4 and throw in a monkey wrench and thats how it ends up. I just accept that and it's all good.

It's still better than paying the rediculous install costs! Nissan wanted $450 to install my Nismo S-Tune suspension!

370Zsteve · 09-13-2010, 01:31 PM

Quote:

Originally Posted by tjlazer

Hahah well I was beat on hard I agree. But in the end I will be driving said Z with HFC's down to the metal recycle yard to cash in on my stock cats for some cash...

It's no surprise to me at all actually. I had a bad feeling it was going to be an EPIC fail moment for me. It always is with me. Whenever I do all my mods I take the stated install times and multiply by 4 and throw in a monkey wrench and thats how it ends up. I just accept that and it's all good.

It's still better than paying the rediculous install costs! Nissan wanted $450 to install my Nismo S-Tune suspension!

It's all good, man! Dem Debbil bolts have claimed many victims.

Holliday · 09-13-2010, 01:40 PM

Quote:

Originally Posted by tjlazer

Hahah well I was beat on hard I agree. But in the end I will be driving said Z with HFC's down to the metal recycle yard to cash in on my stock cats for some cash...

It's no surprise to me at all actually. I had a bad feeling it was going to be an EPIC fail moment for me. It always is with me. Whenever I do all my mods I take the stated install times and multiply by 4 and throw in a monkey wrench and thats how it ends up. I just accept that and it's all good.

It's still better than paying the rediculous install costs! Nissan wanted $450 to install my Nismo S-Tune suspension!

+1 rep just for knowing you were going to FAIL and did it yourself anyway!

Great job man!

Joseph B · 09-14-2010, 11:50 PM

Quote:

Originally Posted by tjlazer

It was a nightmare as at one point I was like screw it. I was about ready to put it all back together and limp it to the nearest Midas. But I was running out of time and this was this only alternative. I was going to win damn it!!! I had stripped out the nut so there was no turning back. Stock cats are not going back, ever.

I know what you mean, sometimes you just have to just get sh.. done. Just be glad your not a tech and it wasn't a customers car or something, "umm, we had to cut your cat in half,here's your car" lol.

One_Quick_Z · 09-21-2010, 01:08 PM

Installed mine without an issue, just had to use extensions for the top flange bolts and a breaker bar. Had them out with Test pipes installed in about an hour. But also used a lift at a co-workers house.

DAN

09-10-2010, 08:44 PM	#31 (permalink)
98intrigue A True Z Fanatic Join Date: Jul 2010 Location: Clearwater, FL Age: 39 Posts: 4,855 Drives: 2014 Viper Rep Power: 430	My car was cold and I left the lubricant on the bolts for a good 2 hours before trying to break them off. __________________ Ryan - 2014 Stryker Green Viper Gone - a few Vipers and a couple turbo VQs

09-13-2010, 01:13 PM	#40 (permalink)
370Zsteve A True Z Fanatic Join Date: Sep 2009 Location: Gold Coast CT Posts: 10,599 Drives: 2019 Corvette G.S. Rep Power: 43	This thread is full of win, lol. Except for you TJ, I have to give the point to the car, man. __________________ SOLD MY Z MARCH 2018 - another Core OG moves on - new ride 2019 Z Corvette Grand Sport - no mods necessary but already have eyes on HFC and intakes LOL IT NEVER ENDS.

09-21-2010, 01:08 PM	#45 (permalink)
One_Quick_Z A True Z Fanatic Join Date: May 2009 Location: Seneca Il Posts: 1,374 Drives: 10 Civic EX Sedan Rep Power: 220	Installed mine without an issue, just had to use extensions for the top flange bolts and a breaker bar. Had them out with Test pipes installed in about an hour. But also used a lift at a co-workers house. DAN __________________ -My BRZ with exhaust will decimate all if we overnight parts from Japan- 10 Civic EX Sedan- Current Daily

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Which HFC or test pipe is the best??	holmanyu	Intake/Exhaust	3	07-19-2010 08:12 AM
Berk Exhaust Production with X-Pipe	Minicobra1	Intake/Exhaust	382	05-24-2010 10:30 PM
Installed Berk Test pipe	>135I	Exterior & Interior	13	09-11-2009 09:04 PM
Berk HFC or Berk Test Pipes?	bobby8621	Intake/Exhaust	16	06-24-2009 05:48 PM

09-12-2010, 06:07 PM	#36 (permalink)
Urbanracer Enthusiast Member Join Date: Oct 2009 Location: The mid-west, USA Posts: 266 Drives: God's Chariot Rep Power: 16	I made it halfway through the installled getting the passender side installed but ended up letting a shop do the drivers side for me. I decided to stop while I was ahead and not distroy the drivers side "b*tch bolt" during my attempt. I noticed a bit of a rattle or leak though when the engine is reved, anyone else experience this? I'm planning on checking the gaskets over when I get time.

09-13-2010, 01:02 PM	#38 (permalink)
Joseph B Base Member Join Date: Jan 2010 Location: Woodinville WA Posts: 160 Drives: '10 Nismo 370Z Rep Power: 16	Removal of the cats on our Z isn't for the faint of heart. It took me about two hours (including jacking it up and down), You have to work slowly, make sure you use a nice penetrant (3m), and have lots of extensions. I used 3/8 and they worked fine. Yes, never use 12 point sockets on something so stubborn, you will strip it. You do NOT need an impact gun for this, probably best you don't use one at all on the exhuast. I feel bad for those that destroyed their cats trying to get them off, what a nightmare. Hope you never need your cats back on.