Fast Intentions "Twin Turbo Kit" is here

FPenvy · 01-29-2015, 07:28 AM

Quote:

Originally Posted by phunk

600 wheel on the 7AT, with a good drag radial should 60' in the 1.6s and I would guess 10.6-10.7 maybe better

son of a bitch........guess I should say sorry to my bank account pre-rape because now my boost-itch is back if this is possible

jwick · 01-29-2015, 08:13 AM

Quote:

Originally Posted by FPenvy

son of a bitch........guess I should say sorry to my bank account pre-rape because now my boost-itch is back if this is possible

It would take a decent driver so your bank account is safe

FPenvy · 01-29-2015, 08:18 AM

Quote:

Originally Posted by jwick

It would take a decent driver so your bank account is safe

anytime you're ready son

jwick · 01-29-2015, 09:21 AM

Quote:

Originally Posted by FPenvy

anytime you're ready son

Pull that Z out of winter storage, bring it and the pink slip to H-town and we can make this happen.

FPenvy · 01-29-2015, 10:18 AM

Quote:

Originally Posted by jwick

Pull that Z out of winter storage, bring it and the pink slip to H-town and we can make this happen.

you running street tires? if so i'm hoping for you vtec to kick in and you just roast the rears

F.I. Inc. · 01-29-2015, 12:38 PM

-UPDATE,

Yesterday was a huge success at the dyno with cycy89's car. As many of you know, we have had his car for quite some time! The road has been long and the process has been tedious, but well worth the wait. The list of mods for this specific car are listed on the dyno chart below. To touch on the 7AT trans itself... The trans has been upgraded with Excedy Clutch Packs. The flex plate has been replaced with our very own "SFI Approved" Billet Aluminum version. The SFI part comes in very handy for you drag racers! In addition, our Trans Cooler featuring a Setrab core as well. The torque converter in stock trim work just fine and has a stall of about 2200 rpm. The stock valve body in the 7AT already comes beefed up over the previous 5AT and shifts like a dream. If needed we will dip into the art of making our own aftermarket torque converter and valve body upgrade. For now we are going to get some good miles on this puppy under a street load to see what she throws back at us. I can tell you this, the car is insane fast and that's at 7.5 psi. Though this trans is no DCT it has shown us thus far that it can handle every high speed shift that we have thrown at it! We will put the car/trans through our rigorous test in the next few weeks prior to sending her home to Cy. Maybe, just maybe we can get some Driveshaft Shop upgraded axles installed and go get that 10 second pass.

FPenvy · 01-29-2015, 12:51 PM

Quote:

Originally Posted by F.I. Inc.

-UPDATE,

Yesterday was a huge success at the dyno with cycy89's car. As many of you know, we have had his car for quite some time! The road has been long and the process has been tedious, but well worth the wait. The list of mods for this specific car are listed on the dyno chart below. To touch on the 7AT trans itself... The trans has been upgraded with Excedy Clutch Packs. The flex plate has been replaced with our very own "SFI Approved" Billet Aluminum version. The SFI part comes in very handy for you drag racers! In addition, our Trans Cooler featuring a Setrab core as well. The torque converter in stock trim work just fine and has a stall of about 2200 rpm. The stock valve body in the 7AT already comes beefed up over the previous 5AT and shifts like a dream. If needed we will dip into the art of making our own aftermarket torque converter and valve body upgrade. For now we are going to get some good miles on this puppy under a street load to see what she throws back at us. I can tell you this, the car is insane fast and that's at 7.5 psi. Though this trans is no DCT it has shown us thus far that it can handle every high speed shift that we have thrown at it! We will put the car/trans through our rigorous test in the next few weeks prior to sending her home to Cy. Maybe, just maybe we can get some Driveshaft Shop upgraded axles installed and go get that 10 second pass.

( Click to show/hide )

oh sweet jesus. tony I think you've outdone yourself yet again my friend.

hats off to you and the FI crew

I think I need some alone time with this dyno graph and information.......excuse me gentleman

Leroydsouza · 01-30-2015, 02:53 PM

Quote:

Originally Posted by F.I. Inc.

-UPDATE,

Yesterday was a huge success at the dyno with cycy89's car. As many of you know, we have had his car for quite some time! The road has been long and the process has been tedious, but well worth the wait. The list of mods for this specific car are listed on the dyno chart below. To touch on the 7AT trans itself... The trans has been upgraded with Excedy Clutch Packs. The flex plate has been replaced with our very own "SFI Approved" Billet Aluminum version. The SFI part comes in very handy for you drag racers! In addition, our Trans Cooler featuring a Setrab core as well. The torque converter in stock trim work just fine and has a stall of about 2200 rpm. The stock valve body in the 7AT already comes beefed up over the previous 5AT and shifts like a dream. If needed we will dip into the art of making our own aftermarket torque converter and valve body upgrade. For now we are going to get some good miles on this puppy under a street load to see what she throws back at us. I can tell you this, the car is insane fast and that's at 7.5 psi. Though this trans is no DCT it has shown us thus far that it can handle every high speed shift that we have thrown at it! We will put the car/trans through our rigorous test in the next few weeks prior to sending her home to Cy. Maybe, just maybe we can get some Driveshaft Shop upgraded axles installed and go get that 10 second pass.

I kinda lost you.
Idk what all this means, I read boost,7AT,Transmission

umm layman terms ?

someone translate

Also do you need core for whatever it is that you are doing.
idk anything. and idc. I just want to hit boost without blowing my transmission

jwick · 01-29-2015, 01:01 PM

Quote:

Originally Posted by FPenvy

you running street tires? if so i'm hoping for you vtec to kick in and you just roast the rears

VTEC????

Did we jump into a Honda forum?

elperuano · 01-29-2015, 12:46 PM

Quote:

Originally Posted by FPenvy

son of a bitch........guess I should say sorry to my bank account pre-rape because now my boost-itch is back if this is possible

You got the 7 year itch or something? For as long as I've seen you post here you been saying you got a "boost" itch. Time to just give it up.

FPenvy · 01-29-2015, 12:55 PM

Quote:

Originally Posted by elperuano

You got the 7 year itch or something? For as long as I've seen you post here you been saying you got a "boost" itch. Time to just give it up.

the exact reason of not boosting my car has been no real solid 7AT upgrades aside from GTM's stg4 tranny......enough said by the company name itself why I didn't go that way.

then recently level10 came forward with theirs and I've been patiently waiting to see what Tony had up his sleeve since through multiple conversations with him I knew something amazing was in the works.

I want boost but until recently I would have had to baby it with the AT and also given up usage of gears 5, 6, and 7 if in the boost at all. now hopefully with these upgrades the 7AT can be fully functional with boost and the power that turbos can provide.

jwick · 01-29-2015, 01:04 PM

Quote:

Originally Posted by elperuano

You got the 7 year itch or something? For as long as I've seen you post here you been saying you got a "boost" itch. Time to just give it up.

and

01-29-2015, 12:38 PM	#6 (permalink)
F.I. Inc. The370Z.com Sponsor Join Date: Feb 2009 Location: Simi Valley, CA Posts: 2,989 Drives: 2010 GT-R/2007 F-250 Rep Power: 687	-UPDATE, Yesterday was a huge success at the dyno with cycy89's car. As many of you know, we have had his car for quite some time! The road has been long and the process has been tedious, but well worth the wait. The list of mods for this specific car are listed on the dyno chart below. To touch on the 7AT trans itself... The trans has been upgraded with Excedy Clutch Packs. The flex plate has been replaced with our very own "SFI Approved" Billet Aluminum version. The SFI part comes in very handy for you drag racers! In addition, our Trans Cooler featuring a Setrab core as well. The torque converter in stock trim work just fine and has a stall of about 2200 rpm. The stock valve body in the 7AT already comes beefed up over the previous 5AT and shifts like a dream. If needed we will dip into the art of making our own aftermarket torque converter and valve body upgrade. For now we are going to get some good miles on this puppy under a street load to see what she throws back at us. I can tell you this, the car is insane fast and that's at 7.5 psi. Though this trans is no DCT it has shown us thus far that it can handle every high speed shift that we have thrown at it! We will put the car/trans through our rigorous test in the next few weeks prior to sending her home to Cy. Maybe, just maybe we can get some Driveshaft Shop upgraded axles installed and go get that 10 second pass. __________________ *Follow us on Facebook: Fast Intentions Inc.* Phone: (805) 522-FAST (3278) Email: tony@fastintentions.com www.fastintentions.com "FUELED BY PASSION" Last edited by F.I. Inc.; 01-29-2015 at 12:41 PM.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Fast Intentions 3" (Twin Turbo) exhaust is here!	F.I. Inc.	Intake/Exhaust	91	02-08-2017 05:09 AM
Fast Intentions "Twin Turbo Kit" Official Release	F.I. Inc.	Drivetrain/Engine	95	11-19-2014 11:38 PM
Twin Turbo vs. Single Turbo V6: A Dissertation	Mike@GTM	Forced Induction	115	08-14-2014 09:04 PM
Twin scroll vs twin turbo	SS_Firehawk	Forced Induction	32	04-13-2014 12:02 PM
GTM Motorsports Twin Turbo vs Greddy Twin Turbo Kit	Nismo221	Forced Induction	57	08-16-2011 04:44 PM

*****Fast Intentions "Twin Turbo Kit" is here*****

Fast Intentions "Twin Turbo Kit" is here