Maf ?

Nut_N_Much · 12-13-2012, 09:16 PM

Okay,
I have been shopping for MAF Sensors I found 3 different ones on the GTM site, I am sure there are probably others out there but I haven't found them.... The 3 they had listed are UpRev, GTM, PMASS. Below is some info on each. I am trying to get the most reliable and programmable by UpRev. I have done some searches on the forum but only found info on UpRev MAFs. Please someone take me to school !!!!

1st - PMASS PREFORAMCE MAF SENSOR
DESCRIPTION:
Probably the most versatile performance mass air sensor on the market. Complete with the HPX software tool the possibilities are pretty much limitless.

Capable of supporting over 1000WHP, Will never peg, Can be used in ln most any intake system configuration, Great for blow thru or draw thru systems, Never needs re-calibrating, No more need for a conventional mass air sensor assembly, this sensor simply drops into your existing intake plumbing, Small footprint allows for exceptional airflow, Every sensor is repeatable within O.E.M. spec, Software transfer-function generating tool included for using the HPX in different tubing, Limited Lifetime Warranty.

*Doesn't say if its program compatible with UpRev, I have seen a lot of these on Fords.

2nd - GTM PERFORMANCE MAF
GTM Performance Engineering is proud to present our custom calibrated high performance MAF sensor. After tuning hundreds of cars ranging from mild naturally aspirated bolt on Nissans and Infinitis to all out 1000hp Twin Turbo cars, we felt there was a need for a sensor that read more airflow without losing the resolution needed to have a stable idle, good cruise and low load engine operation. By adjusting the design of the MAF sensor, we are able to offer extended range for up to 190% more airflow than the stock sensors. This development translates into having a 1000hp car that starts up every time and can be driven normally on the street.

3rd - UPREV MAF GT
UpRev MAF GT sensor will read almost 180% the air flow range of the factory sensor while allowing stable idle air flow measurements. If you have a Nissan or Infiniti vehicle that you're adding Forced Induction to, you will need this upgraded MAF Sensor. We've worked for many years to offer a MAF sensor that we can put our name on. Finally we have the right sensor. Years of being the only manufacturer to support Forced Induction properly on the Nissan vehicles using the factory ECU has allowed us to understand what our customers need and this is the product we've brought to market.

UpRev MAF GT sensor works on a wide range of current and older model Nissan and Infiniti vehicles. The diameter of the MAF tube changes, so and exact HP or Flow range cannot be stated for each vehicle. Nissan has generally matched the Factory MAF tube to reach the 4.9v range at 130% over the factory HP. If you're adding Forced Induction you will be out flowing the factory MAF sensor. We've designed this MAF sensor to meet those needs.

I got all this info off the GTM site. I have no experience with any of these so input is requested. My build is a Stillen SC, very common kit how ever I have swapped out the impeller with a 928. The out put on the SC is small so the air will be traveling as fast or faster than a turbo set up. So I am looking for a set of reliable MAFs.

1st Question: Are the PMASS & GTM MAFs programmable with UpRev Tune?

2nd Question: Which is more reliable?

3rd Question: What are you using?

Thanks

Nut_N_Much · 12-13-2012, 09:23 PM

PMASS PREFORAMCE MAF SENSOR I am reading good things about on the Ford forums. Seems to be a versatile sensor. From what I read they are very reliable. I just haven't seen if they can be programmed with UpRev Software.

UPREV MAFs I have seen a few threads on 30z forum saying they fail more than the others and they are to expensive.

I haven't seen anything on the GTM MAFs but hey everything they make has good reviews..

seymore4 · 12-14-2012, 10:08 AM

The HPX PMAS was the only option until about a year ago when Uprev made their own. The HPX MAF's are very reliable, but have lower resolution than the MAF GT, and there is some variance in the voltage readings between sensors making it more difficult to get a consistent tune. The MAF GT allows for a lot more fine-tuning.

I'm 99% sure that the GTM MAF is nothing more than a rebranded Uprev MAF GT. Just like their "GTM spec ecu reflash".... its just an Uprev reflash that GTM calls their own, and they sell enough of it that Uprev lets them.

In the rom editor there is an option to select either stock MAF, Uprev MAF GT, or HPX PMAS, and it is all precalibrated. Nothing for the GTM MAF, but then again if its really an uprev maf without the label on it then you would just select MAF GT.

There was a bad batch of MAF GT's last summer that were failing, but to the best of my knowledge that was straightened out and I haven't heard of any failing recently. Anyways if they do fail uprev will warranty them pretty easily.

Legz · 12-14-2012, 10:24 AM

Hmhm I'm interested to know as well, I have GTM stg2 TT with stock MAFs at around 400awhp, not sure if upgrading stock MAF is required when not pushing out mad power?

seymore4 · 12-14-2012, 10:38 AM

Quote:

Originally Posted by Legz

Hmhm I'm interested to know as well, I have GTM stg2 TT with stock MAFs at around 400awhp, not sure if upgrading stock MAF is required when not pushing out mad power?

You will be fine

Mike@GTM · 12-14-2012, 12:05 PM

Quote:

Originally Posted by seymore4

I'm 99% sure that the GTM MAF is nothing more than a rebranded Uprev MAF GT. Just like their "GTM spec ecu reflash".... its just an Uprev reflash that GTM calls their own, and they sell enough of it that Uprev lets them.

In the rom editor there is an option to select either stock MAF, Uprev MAF GT, or HPX PMAS, and it is all precalibrated. Nothing for the GTM MAF, but then again if its really an uprev maf without the label on it then you would just select MAF GT.

No, our MAF sensor is NOT an Uprev MAF GT. Our MAF sensors are a different calibration than the UpRev MAF. We developed our MAF's based on our experience with tuning on high powered twin turbo cars using our kits. Also, our MAF sensors come with our own MAF scaling calibration as well. Just so you know, our MAF sensors are manufactured by the same company that manufactures the UpRev MAF...the difference is that our sensors are calibrated to our specifications. Also, unlike the UpRev MAF GT, we have two different MAF sensor calibrations: one that reads 190% more airflow and one that reads 220% more airflow than the stock sensors. We developed the 1000HP MAF specifically for the VQ35DE engine and extreme power VQ35HR's and VQ37VHR's.

Ultimately, our MAF sensors are much easier to tune with than the HPX sensors. While the HPX PMAS is a great sensor, you really have to know what you are doing to make good use of it, otherwise you can easily end up chasing your tail trying to get it dialed in.

In regards to our GTM Spec ECU Flash, it is our own calibration file that we developed. Yes, it uses UpRev tuning software, but it is our tune and our intellectual property. So we have every right to call our tune our GTM Spec ECU Flash.

Nut_N_Much · 12-14-2012, 02:08 PM

Quote:

Originally Posted by seymore4

The HPX PMAS was the only option until about a year ago when Uprev made their own. The HPX MAF's are very reliable, but have lower resolution than the MAF GT, and there is some variance in the voltage readings between sensors making it more difficult to get a consistent tune. The MAF GT allows for a lot more fine-tuning.

I'm 99% sure that the GTM MAF is nothing more than a rebranded Uprev MAF GT. Just like their "GTM spec ecu reflash".... its just an Uprev reflash that GTM calls their own, and they sell enough of it that Uprev lets them.

In the rom editor there is an option to select either stock MAF, Uprev MAF GT, or HPX PMAS, and it is all precalibrated. Nothing for the GTM MAF, but then again if its really an uprev maf without the label on it then you would just select MAF GT.

There was a bad batch of MAF GT's last summer that were failing, but to the best of my knowledge that was straightened out and I haven't heard of any failing recently. Anyways if they do fail uprev will warranty them pretty easily.

Man, thanks for the input, that clears up all the questions

I had. That bad batch may have been what I was reading about.

Quote:

Originally Posted by Mike@GTM

No, our MAF sensor is NOT an Uprev MAF GT. Our MAF sensors are a different calibration than the UpRev MAF. We developed our MAF's based on our experience with tuning on high powered twin turbo cars using our kits. Also, our MAF sensors come with our own MAF scaling calibration as well. Just so you know, our MAF sensors are manufactured by the same company that manufactures the UpRev MAF...the difference is that our sensors are calibrated to our specifications. Also, unlike the UpRev MAF GT, we have two different MAF sensor calibrations: one that reads 190% more airflow and one that reads 220% more airflow than the stock sensors. We developed the 1000HP MAF specifically for the VQ35DE engine and extreme power VQ35HR's and VQ37VHR's.

Ultimately, our MAF sensors are much easier to tune with than the HPX sensors. While the HPX PMAS is a great sensor, you really have to know what you are doing to make good use of it, otherwise you can easily end up chasing your tail trying to get it dialed in.

In regards to our GTM Spec ECU Flash, it is our own calibration file that we developed. Yes, it uses UpRev tuning software, but it is our tune and our intellectual property. So we have every right to call our tune our GTM Spec ECU Flash.

Good to know

, the info on the GTM MAF's. Thank you for the info

.

esfourteen · 12-14-2012, 02:24 PM

Quote:

Originally Posted by Legz

Hmhm I'm interested to know as well, I have GTM stg2 TT with stock MAFs at around 400awhp, not sure if upgrading stock MAF is required when not pushing out mad power?

he needs upgraded MAFs due to the horrible intake design on the stillen supercharger kit. the GTM TT piping is good for about 600whp on stock MAF's I believe.

elperuano · 12-14-2012, 02:49 PM

Yea stock MAFs should be fine up until around 600. I'm running stock MAF and I'm at 534. No problems at all here

bullitt5897 · 12-14-2012, 02:57 PM

OEM MAFs are good for more than 600... We didnt change them on the 4.5L until we were going for over 1000hp...

elperuano · 12-14-2012, 03:00 PM

Quote:

Originally Posted by Bullitt@UAMotorsports

OEM MAFs are good for more than 600... We didnt change them on the 4.5L until we were going for over 1000hp...

That's good to know! Well that settles that!

Mr.Squeeze · 12-14-2012, 03:44 PM

My Maf's were just about done at around 550whp I guess you can call me the unlucky one.

I remember back when i had my 350z around 350whp with uprev the stock maf had to be changed, there were some people however that got 400 whp plus.

elperuano · 12-14-2012, 04:07 PM

Quote:

Originally Posted by Mr.Squeeze

My Maf's were just about done at around 550whp I guess you can call me the unlucky one.

I remember back when i had my 350z around 350whp with uprev the stock maf had to be changed, there were some people however that got 400 whp plus.

That sucks, on my g35 with the gt35r turbo I put down 420 on a mustang and my MAF held up fine.. Guess it's all luck.

Mr.Squeeze · 12-15-2012, 03:09 AM

Quote:

Originally Posted by elperuano

That sucks, on my g35 with the gt35r turbo I put down 420 on a mustang and my MAF held up fine.. Guess it's all luck.

At around 600whp seem to be the point where there max is what i here the most. When I was talking to Sam about my goals he told me I would need the Maf's and he was right.

Nut_N_Much · 12-15-2012, 09:33 AM

Quote:

Originally Posted by esfourteen

he needs upgraded MAFs due to the horrible intake design on the stillen supercharger kit. the GTM TT piping is good for about 600whp on stock MAF's I believe.

Absolutely Right

, also with the impeller swap the system will be pulling more air.

Daily driver with 60,000 on it, if a set of MAF's keeps me out of the red and reliable with the Stillen design I'm all for it. Rather do it all at once then going back and forth to the tuner. $700.00 upfront will save me some $$$ in the long run. Think I'll use the UpRev MAF's.

Most you guy's are running mad HP, I just need to get this kit set up to run another 60,000 miles on it. Man, thanks for all the input, I am getting a lot out of the thread. Trying to stay on the Mr. Squeeze build path. A few there's built there Stillens like him and have had no issues. I got the kit on the cheap was the main reason I got it. I know it will meet my needs, I'm not so Fast and Furious anymore.

Will order the MAF's next week, over X-Mas I plan to get the kit installed and tuned. I have to look at it everyday sitting on the shelf. Driving me crazy. Real test will be Driving to Z-Days in May. Hopefully have the bugs worked out before then.

12-13-2012, 09:16 PM	#1 (permalink)
Nut_N_Much A True Z Fanatic Join Date: Dec 2011 Location: Pensacola Florida Posts: 1,696 Drives: Awesome Car Rep Power: 26	Maf ? Okay, I have been shopping for MAF Sensors I found 3 different ones on the GTM site, I am sure there are probably others out there but I haven't found them.... The 3 they had listed are UpRev, GTM, PMASS. Below is some info on each. I am trying to get the most reliable and programmable by UpRev. I have done some searches on the forum but only found info on UpRev MAFs. Please someone take me to school !!!! 1st - PMASS PREFORAMCE MAF SENSOR DESCRIPTION: Probably the most versatile performance mass air sensor on the market. Complete with the HPX software tool the possibilities are pretty much limitless. Capable of supporting over 1000WHP, Will never peg, Can be used in ln most any intake system configuration, Great for blow thru or draw thru systems, Never needs re-calibrating, No more need for a conventional mass air sensor assembly, this sensor simply drops into your existing intake plumbing, Small footprint allows for exceptional airflow, Every sensor is repeatable within O.E.M. spec, Software transfer-function generating tool included for using the HPX in different tubing, Limited Lifetime Warranty. Doesn't say if its program compatible with UpRev, I have seen a lot of these on Fords. 2nd - GTM PERFORMANCE MAF* GTM Performance Engineering is proud to present our custom calibrated high performance MAF sensor. After tuning hundreds of cars ranging from mild naturally aspirated bolt on Nissans and Infinitis to all out 1000hp Twin Turbo cars, we felt there was a need for a sensor that read more airflow without losing the resolution needed to have a stable idle, good cruise and low load engine operation. By adjusting the design of the MAF sensor, we are able to offer extended range for up to 190% more airflow than the stock sensors. This development translates into having a 1000hp car that starts up every time and can be driven normally on the street. 3rd - UPREV MAF GT UpRev MAF GT sensor will read almost 180% the air flow range of the factory sensor while allowing stable idle air flow measurements. If you have a Nissan or Infiniti vehicle that you're adding Forced Induction to, you will need this upgraded MAF Sensor. We've worked for many years to offer a MAF sensor that we can put our name on. Finally we have the right sensor. Years of being the only manufacturer to support Forced Induction properly on the Nissan vehicles using the factory ECU has allowed us to understand what our customers need and this is the product we've brought to market. UpRev MAF GT sensor works on a wide range of current and older model Nissan and Infiniti vehicles. The diameter of the MAF tube changes, so and exact HP or Flow range cannot be stated for each vehicle. Nissan has generally matched the Factory MAF tube to reach the 4.9v range at 130% over the factory HP. If you're adding Forced Induction you will be out flowing the factory MAF sensor. We've designed this MAF sensor to meet those needs. I got all this info off the GTM site. I have no experience with any of these so input is requested. My build is a Stillen SC, very common kit how ever I have swapped out the impeller with a 928. The out put on the SC is small so the air will be traveling as fast or faster than a turbo set up. So I am looking for a set of reliable MAFs. 1st Question: Are the PMASS & GTM MAFs programmable with UpRev Tune? 2nd Question: Which is more reliable? 3rd Question: What are you using? Thanks __________________ Did new cool science stuff to the car !!! http://www.the370z.com/mazoc/99606-z...y-14-17-a.html http://www.the370z.com/diy-section-d...-w-videos.html Last edited by Nut_N_Much; 12-13-2012 at 09:25 PM. Reason: update

12-13-2012, 09:23 PM	#2 (permalink)
Nut_N_Much A True Z Fanatic Join Date: Dec 2011 Location: Pensacola Florida Posts: 1,696 Drives: Awesome Car Rep Power: 26	PMASS PREFORAMCE MAF SENSOR I am reading good things about on the Ford forums. Seems to be a versatile sensor. From what I read they are very reliable. I just haven't seen if they can be programmed with UpRev Software. UPREV MAFs I have seen a few threads on 30z forum saying they fail more than the others and they are to expensive. I haven't seen anything on the GTM MAFs but hey everything they make has good reviews.. __________________ Did new cool science stuff to the car !!! http://www.the370z.com/mazoc/99606-z...y-14-17-a.html http://www.the370z.com/diy-section-d...-w-videos.html

12-14-2012, 10:08 AM	#3 (permalink)
seymore4 Track Member Join Date: Nov 2010 Location: West coast Age: 41 Posts: 555 Drives: 2010 nismo Rep Power: 6726	The HPX PMAS was the only option until about a year ago when Uprev made their own. The HPX MAF's are very reliable, but have lower resolution than the MAF GT, and there is some variance in the voltage readings between sensors making it more difficult to get a consistent tune. The MAF GT allows for a lot more fine-tuning. I'm 99% sure that the GTM MAF is nothing more than a rebranded Uprev MAF GT. Just like their "GTM spec ecu reflash".... its just an Uprev reflash that GTM calls their own, and they sell enough of it that Uprev lets them. In the rom editor there is an option to select either stock MAF, Uprev MAF GT, or HPX PMAS, and it is all precalibrated. Nothing for the GTM MAF, but then again if its really an uprev maf without the label on it then you would just select MAF GT. There was a bad batch of MAF GT's last summer that were failing, but to the best of my knowledge that was straightened out and I haven't heard of any failing recently. Anyways if they do fail uprev will warranty them pretty easily. Nut_N_Much likes this.

12-14-2012, 10:24 AM	#4 (permalink)
Legz Base Member Join Date: Nov 2009 Location: Calgary, AB Posts: 70 Drives: TT X coupe!! Rep Power: 15	Hmhm I'm interested to know as well, I have GTM stg2 TT with stock MAFs at around 400awhp, not sure if upgrading stock MAF is required when not pushing out mad power? Nut_N_Much likes this. __________________ GTM TT G37x coupe! Stage2 8.5psi Hotchkis \| GTSpec \| Eibach \| PLX \| Exoticspeed

12-14-2012, 02:49 PM	#9 (permalink)
elperuano A True Z Fanatic Join Date: Oct 2011 Location: Southwest FL Posts: 1,374 Drives: G37S Rep Power: 28	Yea stock MAFs should be fine up until around 600. I'm running stock MAF and I'm at 534. No problems at all here Nut_N_Much likes this.

12-14-2012, 02:57 PM	#10 (permalink)
bullitt5897 Premium Member Join Date: Jan 2009 Location: North GA Posts: 6,831 Drives: Twin Turbo Z34 Rep Power: 3682	OEM MAFs are good for more than 600... We didnt change them on the 4.5L until we were going for over 1000hp... Mkai0 and Nut_N_Much like this. __________________ *Shop Cars: 2013 318whp Nismo VspecII 370z SOLD, 2009 1000hp+ 93oct 4.0L TT 370z Fast Intentions STAGE 4 #054*

12-14-2012, 03:44 PM	#12 (permalink)
Mr.Squeeze A True Z Fanatic Join Date: Aug 2010 Location: Keystone state Posts: 1,209 Drives: 2010 370z Rep Power: 20152	My Maf's were just about done at around 550whp I guess you can call me the unlucky one. I remember back when i had my 350z around 350whp with uprev the stock maf had to be changed, there were some people however that got 400 whp plus. Nut_N_Much likes this. __________________ Driven Motorsports Single Turbo 7675 T4 1.32 A/R 995WHP 780TQ