Limp Stillen Supercharger dtc p1239

Z4fun · 10-12-2019, 06:24 AM

Quote:

Originally Posted by fork

I just looked looked at the Michigan Motorsports extensions. They are 5-wire extensions. You could not use them to connect to the TB since the TB connections are 6-wire. All of the Stillen extensions are 6-wire so you can use any of the three that come with the kit to extend to the TB.

I will say, however, that I have tried all three of the Stillen extensions to connect to my TB and at some point or another all three have hit me with the P1239 code.

Sorry, that's incorrect. I have one and they are 6 wires and work fine with my Z , not sure if the quality is better then stillen but we'll see how long they hold up. From the amazon pic its hard to see the wires but if u count the holes in the connector u can see 6. I tried to post a pic but it wouldn't upload

I believe its a heat issue with the wires and going to wrap them in a thermal sleeve as some suggested.

cgr406 · 10-19-2019, 09:40 PM

I've been having this same issue and it's really affecting my enjoyment of the car. It's happened to me probably 7 or 8 times this summer / fall. Seems to be increasing in frequency. It's to the point where I'm uncomfortable driving the car in heavy traffic b/c I never know when it's going to go limp. I've emailed Stillen about this, but of course, I've not heard back from them. I just ordered the Michigan Motorsports cable, so I'll see if that helps / fixes it. Thanks @Z4fun for finding & posting that!

Z4fun · 10-21-2019, 09:41 AM

Quote:

Originally Posted by cgr406

I've been having this same issue and it's really affecting my enjoyment of the car. It's happened to me probably 7 or 8 times this summer / fall. Seems to be increasing in frequency. It's to the point where I'm uncomfortable driving the car in heavy traffic b/c I never know when it's going to go limp. I've emailed Stillen about this, but of course, I've not heard back from them. I just ordered the Michigan Motorsports cable, so I'll see if that helps / fixes it. Thanks @Z4fun for finding & posting that!

I would of bought Topgunz cables since he is selling them for $20, if I knew before. Awesome guy, definitely support him !

My issue was the same it ran fine for about 1 year , then started acting up once in a while then more and more often. Cables shouldn't react like that unless there's an external force acting on them to lower the life span like (heat , tention, ice, ect) I feel changing the cable is a bandaid if we don't fix the underlying issue.

I have the car with my mechanic and we are gonna try to find a way to resolve it permanently, if we can reroute them somehow, or if not insulate the hell out of them I will send some pics when we figure it out.

cgr406 · 10-21-2019, 10:10 AM

I checked w/ Aaron a while back & the replacement cables that he has are the same ones (Stillen Gen II) that came w/ the full SC kit that I bought from him. So, I'm wanting to try something different. I will also try wrapping / insulating the new cable.

Z4fun · 10-21-2019, 01:57 PM

Quote:

Originally Posted by cgr406

I checked w/ Aaron a while back & the replacement cables that he has are the same ones (Stillen Gen II) that came w/ the full SC kit that I bought from him. So, I'm wanting to try something different. I will also try wrapping / insulating the new cable.

Oh ok , makes sense. Plz post pics of ur fix , im sure all of us would like to see how it came out when ur done.

Z4fun · 11-01-2019, 07:36 AM

Hey guys , after some testing and research we concluded the cause is 100% heat. since the wire is being heated its increasing the resistance causing and interruption in the signal throwing the tb off and causing it to go into limp mode.

My mechanic said he tested the wire cold then warmed up the car and tested again and saw a dramatic rise of resistance in the cable. The two options we had is to insulate with a sleeve or try to reroute the wire. Since I am adding a vented hood, we decided to go with the sleeve. (attached pic)

In doing more research this is actually a well known fact in thermal electrical engineering here is the definition for Heat resistance.

Heat Resistance

Heating a metal conductor makes it more difficult for electricity to flow through it.

In metal conductors, electrical current flows due to the exchange of electrons between atoms. As electrons move through a metal conductor, some collide with atoms, other electrons or impurities. These collisions cause resistance and generate heat. Heating the metal conductor causes atoms to vibrate more, which in turn makes it more difficult for the electrons to flow, increasing resistance.

https://nationalmaglab.org/education...eat-resistance

WhiskeyHotel · 11-01-2019, 08:23 AM

Yes, the actual equation is R=Rref(1+a(T-Tref)) and the temp coef (a) of Cu is +0.000393 per degree centigrade. That means the effect is pretty small at the lengths and temps you would experience under your car's hood. (That Bunsen burner temp in your example link is ~1700 degrees C!)

Example: 100 feet of 20 gauge wire with resistance of 1.015 ohms at 20° C (room temp). If the temperature of the wire goes up 10°C, the resistance will change by 0.0399 ohms (10 degrees * 0.00393 per degree * 1.015 ohms = 0.0399 ohms).

The wire resistance will now be 1.015 ohms + 0.0399 ohms = 1.0549 ohms.

In my opinion, that wouldn't be enough change to account for the large increase in resistance your mechanic is seeing. (I think - I don't know what the increase was. I also don't know how the resistance was measured nor do I know which of the conductors he measured and there are grounds, power, and sensor signals going to the throttle body. You can see that I am shooting from the hip here.) My electrical engineering spider sense is tingling at this point. There could be something else going on - connector pins heating up and losing continuity - something. I hope the proposed solution works - but I am a bit skeptical at this point. Let us know how it goes.

Z4fun · 11-02-2019, 08:35 AM

Quote:

Originally Posted by WhiskeyHotel

Yes, the actual equation is R=Rref(1+a(T-Tref)) and the temp coef (a) of Cu is +0.000393 per degree centigrade. That means the effect is pretty small at the lengths and temps you would experience under your car's hood. (That Bunsen burner temp in your example link is ~1700 degrees C!)

Example: 100 feet of 20 gauge wire with resistance of 1.015 ohms at 20° C (room temp). If the temperature of the wire goes up 10°C, the resistance will change by 0.0399 ohms (10 degrees * 0.00393 per degree * 1.015 ohms = 0.0399 ohms).

The wire resistance will now be 1.015 ohms + 0.0399 ohms = 1.0549 ohms.

In my opinion, that wouldn't be enough change to account for the large increase in resistance your mechanic is seeing. (I think - I don't know what the increase was. I also don't know how the resistance was measured nor do I know which of the conductors he measured and there are grounds, power, and sensor signals going to the throttle body. You can see that I am shooting from the hip here.) My electrical engineering spider sense is tingling at this point. There could be something else going on - connector pins heating up and losing continuity - something. I hope the proposed solution works - but I am a bit skeptical at this point. Let us know how it goes.

If your engine only goes up 10 degree from ambient that would be awesome, unfortunately for the rest of us with a cable sitting directly on an engine with an oil temp of 115+- C your resistance formula would make a large difference if you wanna recalculate it.

The point of my response was common sense with alittle info in heat and resistance for some ppl that don't need a degree to understand it. That's why I didn't have to pull formulas and stuff. The cause was heat and the failure is the wire or connector under the heat stress over a "PERIOD OF TIME" not a one time thing. materials can heat and cool multiple times before getting to the breaking point.

we appreciate your criticism, but would rather appreciate a solution to the problem at hand.

cgr406 · 11-02-2019, 07:09 PM

So I installed the Michigan Motorsports TB cable about a week ago & wrapped it in teva tape, just cause it can't hurt. No codes / limp mode so far, but it's only been a week. Tonight i wrapped it in thermal insulation from Summit. So, we'll see how it goes, although now that it's November in PA, not sure how much more I'll be able to drive the car for a while.

WhiskeyHotel · 11-02-2019, 10:20 PM

No criticism intended.

Optimiser · 05-19-2020, 09:36 PM

Quote:

Originally Posted by cgr406

So I installed the Michigan Motorsports TB cable about a week ago & wrapped it in teva tape, just cause it can't hurt. No codes / limp mode so far, but it's only been a week. Tonight i wrapped it in thermal insulation from Summit. So, we'll see how it goes, although now that it's November in PA, not sure how much more I'll be able to drive the car for a while.

It's been a year so how is it now? More reliable?

cgr406 · 05-20-2020, 03:57 PM

Yep, so far so good. Although I've only put about 1,600 mi on it. The original stillen cable was OK for a while too, so I'm not sure this is enough of a test to be conclusive. I probably had about 3.5k mi on the Stillen cable before it started crapping out. Fingers crossed.

vqholic@Korea · 09-27-2020, 10:54 AM

Quote:

Originally Posted by cgr406

Yep, so far so good. Although I've only put about 1,600 mi on it. The original stillen cable was OK for a while too, so I'm not sure this is enough of a test to be conclusive. I probably had about 3.5k mi on the Stillen cable before it started crapping out. Fingers crossed.

I also suffered by p1239. Seeing this thread, Hannes was insulated and passed through the summer without any problems. Now that autumn has come, limp mode is back on, and the fault code represents p1239.
It ran about 3,000 mi. Fucxxxx

Optimiser · 09-27-2020, 09:01 PM

I'm thinking the only way to fix this problem is to use TopGunz new kit (or piping) that utilizes the stock manifold and therefore stock (length) TB wiring harness.

DrBacon · 09-27-2020, 11:17 PM

Quote:

Originally Posted by Optimiser

I'm thinking the only way to fix this problem is to use TopGunz new kit (or piping) that utilizes the stock manifold and therefore stock (length) TB wiring harness.

Would be nice if the extensions were proper length, I had to loop the excess because I didn't know what else to do with it.

10-19-2019, 09:40 PM	#92 (permalink)
cgr406 Base Member Join Date: Sep 2013 Location: pittsburgh Posts: 106 Drives: '14 Z Sport Tour 6M Rep Power: 3366	I've been having this same issue and it's really affecting my enjoyment of the car. It's happened to me probably 7 or 8 times this summer / fall. Seems to be increasing in frequency. It's to the point where I'm uncomfortable driving the car in heavy traffic b/c I never know when it's going to go limp. I've emailed Stillen about this, but of course, I've not heard back from them. I just ordered the Michigan Motorsports cable, so I'll see if that helps / fixes it. Thanks @Z4fun for finding & posting that! Optimiser, wideglideleon and Z4fun like this. __________________ TopGunZ Rotrex SC / CJM RFS / 1300 / Ecutek / Dynosty / F.I. TP & CBE / Z1 / Swift / SPL / Whiteline / Hotchkis / Michelin SP4

10-21-2019, 10:10 AM	#94 (permalink)
cgr406 Base Member Join Date: Sep 2013 Location: pittsburgh Posts: 106 Drives: '14 Z Sport Tour 6M Rep Power: 3366	I checked w/ Aaron a while back & the replacement cables that he has are the same ones (Stillen Gen II) that came w/ the full SC kit that I bought from him. So, I'm wanting to try something different. I will also try wrapping / insulating the new cable. __________________ TopGunZ Rotrex SC / CJM RFS / 1300 / Ecutek / Dynosty / F.I. TP & CBE / Z1 / Swift / SPL / Whiteline / Hotchkis / Michelin SP4

11-01-2019, 08:23 AM	#97 (permalink)
WhiskeyHotel Track Member Join Date: Nov 2009 Location: Oklahoma Posts: 530 Drives: 2015 GT-R PW Premium Rep Power: 16	Yes, the actual equation is R=Rref(1+a(T-Tref)) and the temp coef (a) of Cu is +0.000393 per degree centigrade. That means the effect is pretty small at the lengths and temps you would experience under your car's hood. (That Bunsen burner temp in your example link is ~1700 degrees C!) Example: 100 feet of 20 gauge wire with resistance of 1.015 ohms at 20° C (room temp). If the temperature of the wire goes up 10°C, the resistance will change by 0.0399 ohms (10 degrees * 0.00393 per degree * 1.015 ohms = 0.0399 ohms). The wire resistance will now be 1.015 ohms + 0.0399 ohms = 1.0549 ohms. In my opinion, that wouldn't be enough change to account for the large increase in resistance your mechanic is seeing. (I think - I don't know what the increase was. I also don't know how the resistance was measured nor do I know which of the conductors he measured and there are grounds, power, and sensor signals going to the throttle body. You can see that I am shooting from the hip here.) My electrical engineering spider sense is tingling at this point. There could be something else going on - connector pins heating up and losing continuity - something. I hope the proposed solution works - but I am a bit skeptical at this point. Let us know how it goes. Last edited by WhiskeyHotel; 11-01-2019 at 08:28 AM.

11-02-2019, 10:20 PM	#100 (permalink)
WhiskeyHotel Track Member Join Date: Nov 2009 Location: Oklahoma Posts: 530 Drives: 2015 GT-R PW Premium Rep Power: 16	No criticism intended. Z4fun likes this.

05-20-2020, 03:57 PM	#102 (permalink)
cgr406 Base Member Join Date: Sep 2013 Location: pittsburgh Posts: 106 Drives: '14 Z Sport Tour 6M Rep Power: 3366	Yep, so far so good. Although I've only put about 1,600 mi on it. The original stillen cable was OK for a while too, so I'm not sure this is enough of a test to be conclusive. I probably had about 3.5k mi on the Stillen cable before it started crapping out. Fingers crossed. Optimiser likes this. __________________ TopGunZ Rotrex SC / CJM RFS / 1300 / Ecutek / Dynosty / F.I. TP & CBE / Z1 / Swift / SPL / Whiteline / Hotchkis / Michelin SP4

09-27-2020, 09:01 PM	#104 (permalink)
Optimiser Enthusiast Member Join Date: Mar 2013 Location: Australia Posts: 453 Drives: 2012 Nissan 370Z MT Rep Power: 20144	I'm thinking the only way to fix this problem is to use TopGunz new kit (or piping) that utilizes the stock manifold and therefore stock (length) TB wiring harness. Spooler and vqholic@Korea like this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
P1239 throttle position sensor	ThamerZ370	Tuning	5	12-19-2015 12:47 PM
[WTB] stillen supercharger	mathys92	Parts for sale (Private Classifieds)	0	03-02-2015 08:03 AM
[FOR SALE] Stillen supercharger kit	mr-emv	Parts for sale (Private Classifieds)	11	09-07-2013 11:07 AM
FS: Stillen Supercharger kit	Elysium	Canada	11	03-31-2012 08:05 AM
Stillen or gtm supercharger?	germanattitud	Forced Induction	34	08-07-2011 01:47 PM