Stillen Air to Air setup

JWillis72 · 02-09-2016, 09:27 AM

Quote:

Originally Posted by jwick

This the first AT they e ever worked on?

Nice job btw

No there are 3 GRT there right now with the trans out, he said they didn't need one to fill them.

JWillis72 · 02-09-2016, 05:29 PM

I went and filled the trans with him so he couldn't blow it off but once again it's holding a quart less than Level 10 said it should so no dyno tonight. I emailed Level 10 to see what they say before we continue.

StillenZ84 · 02-09-2016, 05:37 PM

Quote:

Originally Posted by JWillis72

I went and filled the trans with him so he couldn't blow it off but once again it's holding a quart less than Level 10 said it should so no dyno tonight. I emailed Level 10 to see what they say before we continue.

How much did they tell you it is suppose to hold? Do you have the trans cooler?

JWillis72 · 02-09-2016, 06:06 PM

They told me to add 10 quarts and that it should self level around 9.7 when up to temp.

Sent from my iPhone using Tapatalk

JWillis72 · 02-09-2016, 06:07 PM

It's only holding 8.5.

Sent from my iPhone using Tapatalk

StillenZ84 · 02-09-2016, 07:10 PM

Ok yeah dude mine only held between 8-9 also. I think 10 is impossible.

JWillis72 · 02-09-2016, 07:23 PM

Thank you man, he has told me 9.7 this whole time and we have tried 7 or 8 times and it only ever holds 8.5. Pats a super nice guy but clearly he must be thinking of a different trans.

Sent from my iPhone using Tapatalk

blobbish · 02-10-2016, 04:44 AM

Quote:

Originally Posted by JWillis72

Thank you man, he has told me 9.7 this whole time and we have tried 7 or 8 times and it only ever holds 8.5. Pats a super nice guy but clearly he must be thinking of a different trans.

Sent from my iPhone using Tapatalk

Is the car running when you add the remainder of the oil?

I only ask because as part of the oil change on the trans you have to add the required amount (quickly replacing the screw) start the car then remove the screw, excess will drain but if nothing comes out then you can add more at this stage, while the engine is running, until it starts to drain. It should be at the right level then. Replace the sump screw and your away.

JWillis72 · 02-10-2016, 06:38 AM

Quote:

Originally Posted by blobbish

Is the car running when you add the remainder of the oil?

I only ask because as part of the oil change on the trans you have to add the required amount (quickly replacing the screw) start the car then remove the screw, excess will drain but if nothing comes out then you can add more at this stage, while the engine is running, until it starts to drain. It should be at the right level then. Replace the sump screw and your away.

We had a copper tube on the pump with a small piece of the clear hose about 1" from the tip that worked as a plug so we could fill it with the car off. We then ran the car until the pan was 100 degrees and pulled the plug with the car running. The first time we filled it Pat didn't tell me to do it running and it was trying to dump all the fluid.

StillenZ84 · 02-10-2016, 07:19 AM

Yeah the Nissan dealership is who installed my Level 10 trans.

EVOHUNTER · 02-10-2016, 07:57 AM

Maybe this will help?

Install a new O-ring to the charge pipe tool NO. 310811EA5A or equivalent. Connect a scan tool to the DLC and monitor transmission fluid temperature. Start the engine and warm the transmission to approximately 104°F (40°C) NOTE: temperature greatly affects fluid level. Ensure temperature remains constant during checking procedure. With vehicle on a level surface shift the transmission through each gear, then return to the P position. Raise the vehicle and remove the overflow checking plug from the pan. Install charge pipe tool NO. 310811EA5A or equivalent. HAND TIGHTEN only. Connect a suitable fluid pump to the charge pipe and add 0.5 liters of the correct fluid to the transmission. Remove the charge pipe. If no fluid flows from the overflow hole Continue adding fluid. Allow fluid to drain until it drips. Install and tighten overflow plug.

this is now much Nissan says it should take.

Liters 9.2 Quarts 9.7

If you don't shift through the gears it wont take all the fluid!

StillenZ84 · 02-10-2016, 08:46 AM

Well let me know Jason if you are able to get 9.7 quarts in. I figured the dealership would know how much to put in. If that is what they call for then Im guessing it has to fit somehow. Im going to call my buddy at Nissan today to see why they only put 8.5 in mine.

EVOHUNTER · 02-10-2016, 09:27 AM

Quote:

Originally Posted by StillenZ84

Well let me know Jason if you are able to get 9.7 quarts in. I figured the dealership would know how much to put in. If that is what they call for then Im guessing it has to fit somehow. Im going to call my buddy at Nissan today to see why they only put 8.5 in mine.

Im not sure what the level ten in tales,

But maybe theres less room for fluid now???

JWillis72 · 02-10-2016, 12:01 PM

Level ten left out the shifting it part in his instructions to me! S**t, I just drove it and it seemed fine. We were going to dyno it at three but I guess it back to the lift and there is a car on it.

StillenZ84 · 02-10-2016, 12:43 PM

Quote:

Originally Posted by JWillis72

Level ten left out the shifting it part in his instructions to me! S**t, I just drove it and it seemed fine. We were going to dyno it at three but I guess it back to the lift and there is a car on it.

Yeah I have been driving mine for 5+ months and it has seemed fine.

02-09-2016, 06:07 PM	#1310 (permalink)
JWillis72 A True Z Fanatic Join Date: Sep 2013 Location: Fort Myers FL Posts: 2,002 Drives: 2009 370Z yellow 7AT Rep Power: 44	It's only holding 8.5. Sent from my iPhone using Tapatalk StillenZ84 likes this.

02-09-2016, 07:10 PM	#1311 (permalink)
StillenZ84 Enthusiast Member Join Date: Oct 2014 Location: OKC, OK Posts: 316 Drives: 2010 370Z 7AT S/C Rep Power: 17	Ok yeah dude mine only held between 8-9 also. I think 10 is impossible. __________________ AtA SC\|9 lb pulley\|2.85" SC\|3.47" Jack\|E85\|CJM S1-SE\|ID1000s\|Walboro 485\|Zeitronix FF\|Stillen CBE\|AP Racing\|Level 10\|F.I. Flex plate\|Nismo-S tune\|EcuTek RaceRom\|Sebz\|Speed density\|Haltech\|3GsCustoms Dual pod a-pillar\|Carbon Signal GTR gauges\|Fujimura\|Built\| CP Pistons/Carrillo rods\|PortPolishHeads/intakes\|928motorsports IG: evanosteenz34

02-09-2016, 07:23 PM	#1312 (permalink)
JWillis72 A True Z Fanatic Join Date: Sep 2013 Location: Fort Myers FL Posts: 2,002 Drives: 2009 370Z yellow 7AT Rep Power: 44	Thank you man, he has told me 9.7 this whole time and we have tried 7 or 8 times and it only ever holds 8.5. Pats a super nice guy but clearly he must be thinking of a different trans. Sent from my iPhone using Tapatalk StillenZ84 likes this.

02-10-2016, 07:19 AM	#1315 (permalink)
StillenZ84 Enthusiast Member Join Date: Oct 2014 Location: OKC, OK Posts: 316 Drives: 2010 370Z 7AT S/C Rep Power: 17	Yeah the Nissan dealership is who installed my Level 10 trans. JWillis72 likes this. __________________ AtA SC\|9 lb pulley\|2.85" SC\|3.47" Jack\|E85\|CJM S1-SE\|ID1000s\|Walboro 485\|Zeitronix FF\|Stillen CBE\|AP Racing\|Level 10\|F.I. Flex plate\|Nismo-S tune\|EcuTek RaceRom\|Sebz\|Speed density\|Haltech\|3GsCustoms Dual pod a-pillar\|Carbon Signal GTR gauges\|Fujimura\|Built\| CP Pistons/Carrillo rods\|PortPolishHeads/intakes\|928motorsports IG: evanosteenz34

02-10-2016, 07:57 AM	#1316 (permalink)
EVOHUNTER Track Member Join Date: Jul 2011 Location: Edmonton, Canada Posts: 681 Drives: BOOSTED3-7-0 Rep Power: 14	Maybe this will help? Install a new O-ring to the charge pipe tool NO. 310811EA5A or equivalent. Connect a scan tool to the DLC and monitor transmission fluid temperature. Start the engine and warm the transmission to approximately 104°F (40°C) NOTE: temperature greatly affects fluid level. Ensure temperature remains constant during checking procedure. With vehicle on a level surface shift the transmission through each gear, then return to the P position. Raise the vehicle and remove the overflow checking plug from the pan. Install charge pipe tool NO. 310811EA5A or equivalent. HAND TIGHTEN only. Connect a suitable fluid pump to the charge pipe and add 0.5 liters of the correct fluid to the transmission. Remove the charge pipe. If no fluid flows from the overflow hole Continue adding fluid. Allow fluid to drain until it drips. Install and tighten overflow plug. this is now much Nissan says it should take. Liters 9.2 Quarts 9.7 If you don't shift through the gears it wont take all the fluid! __________________ Last edited by EVOHUNTER; 02-10-2016 at 08:00 AM.

02-09-2016, 05:29 PM	#1307 (permalink)
JWillis72 A True Z Fanatic Join Date: Sep 2013 Location: Fort Myers FL Posts: 2,002 Drives: 2009 370Z yellow 7AT Rep Power: 44	I went and filled the trans with him so he couldn't blow it off but once again it's holding a quart less than Level 10 said it should so no dyno tonight. I emailed Level 10 to see what they say before we continue.

02-09-2016, 06:06 PM	#1309 (permalink)
JWillis72 A True Z Fanatic Join Date: Sep 2013 Location: Fort Myers FL Posts: 2,002 Drives: 2009 370Z yellow 7AT Rep Power: 44	They told me to add 10 quarts and that it should self level around 9.7 when up to temp. Sent from my iPhone using Tapatalk

02-10-2016, 08:46 AM	#1317 (permalink)
StillenZ84 Enthusiast Member Join Date: Oct 2014 Location: OKC, OK Posts: 316 Drives: 2010 370Z 7AT S/C Rep Power: 17	Well let me know Jason if you are able to get 9.7 quarts in. I figured the dealership would know how much to put in. If that is what they call for then Im guessing it has to fit somehow. Im going to call my buddy at Nissan today to see why they only put 8.5 in mine. __________________ AtA SC\|9 lb pulley\|2.85" SC\|3.47" Jack\|E85\|CJM S1-SE\|ID1000s\|Walboro 485\|Zeitronix FF\|Stillen CBE\|AP Racing\|Level 10\|F.I. Flex plate\|Nismo-S tune\|EcuTek RaceRom\|Sebz\|Speed density\|Haltech\|3GsCustoms Dual pod a-pillar\|Carbon Signal GTR gauges\|Fujimura\|Built\| CP Pistons/Carrillo rods\|PortPolishHeads/intakes\|928motorsports IG: evanosteenz34

02-10-2016, 12:01 PM	#1319 (permalink)
JWillis72 A True Z Fanatic Join Date: Sep 2013 Location: Fort Myers FL Posts: 2,002 Drives: 2009 370Z yellow 7AT Rep Power: 44	Level ten left out the shifting it part in his instructions to me! S**t, I just drove it and it seemed fine. We were going to dyno it at three but I guess it back to the lift and there is a car on it.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Custom intake setup -- Stillen G3's, Velocity Stacks, Custom Front Crash Beam, pics	'10Anamoly	Intake/Exhaust	26	02-14-2015 10:59 AM
My new setup :)	Flushnismo	Nissan 370Z Photos / Spyshots / Video / Media Gallery	30	06-29-2012 11:03 AM
[WTB] wtb nismo seats stillen g3 cai stillen headers and stillen exhaust	bloodvayne	Parts for sale (Private Classifieds)	1	12-18-2011 09:25 PM
Stillen Sway bars - 305 rear tires - setup?	FricFrac	Track / Autocross / Drifting / Dragstrip	2	02-15-2011 10:33 AM
Full Stillen Bolt-On Setup - Videos!	RCZ	Intake/Exhaust	114	06-15-2009 04:32 PM