Done :tiphat:

Thank you! Let me know when you want a carbonfiber version for your cubby set up. :icon17:

They are very time consuming. Thank you for the compliments. :tiphat:

I have a "base" ready and waiting to be fabricated into someone's idea. :tup:

So, it's gonna be a couple of weeks for me to get my pillar, but I wanted to know where would be the best place to get power for the wideband? Don't know were I read it, but it was not recommended to wire the wideband to an Acc wire. Where do you guys normally tap into?

Can I get a quote on a double pillar gauge shipped to 38002? And a separate one for the cubby for 2 spots? Im trying to figure out what I want to do. I had the gauges in the dash but ill probably be swapping back to factory gauges there for ECUtek. Idk yet.

You can find the necessary sources at the left kick panel fuse panel. Use a multimeter and fuse tap on the needed wires.

Done :tiphat:

I'm interested in a single pillar shipped to 30019.

Cubby gauge setup shipped to 34119


Sent from my iPhone using Tapatalk

Done :tiphat:

Done :tiphat:

More going out to members,

https://farm2.staticflickr.com/1694/...c6e73957_c.jpgUntitled

Mmmmm. Love the premium pillars.

Jason

You think you could pull off a premium pillar for a G now that you've done a few?

Are you talking about having the same look as the 370z pillar? Yes.

Yes. I like how they have contours and such. Obviously they would be colored like the G but I like how the pod cups are fancy and don't look like cups molded to the pillar.

Pm price single silver ring guage and cubby to 85021 thx

I can and should I guess. The only reason I didn't in the first place is because the G37 does't have any of the same design cues. Buuuuut, if it's wanted by the members, I'm more than happy to fabricate it.

They look so sweet I don't think anyone would notice it doesn't flow.

Sweet pillar man, thanks :tiphat:

That was quick! Nice set-up. Thanks for sharing :tiphat:

Got mine today... beautiful piece and thanks again!

I'm happy that it arrived safely. Glad you like it. Thank you :tiphat:

Is the most expensive one on the top and the cheapest in the bottom? :tup:

Nice work - car audio geekness came in handy.

I want this
 

Galeforce, I would like to order the cubby gauge mount that you have shown. Standard black, two 52mm gauges side by side as shown in the picture.

PM me with ordering instructions to 35749 please.

Cubby mount
 

Ordered my cubby mount today with trim rings. Looks awesome!

Price for single pod w/ silver ring pillar shipped to 94041. Also what is the price difference if I send you my pillar along with the gauge itself? Planning to use a tanabe 52mm gauge. Thanks.

PM'd :tiphat:

http://uploads.tapatalk-cdn.com/2016...fe606ccad2.jpg

Installed. Very happy with it.

Sent from my SM-N920V using Tapatalk

Nice! :tup:

Edit, your inbox is full. I tried to send you a PM.

Fixed

Sent from my SM-N920V using Tapatalk

http://uploads.tapatalk-cdn.com/2016...acb87c0f16.jpg

Gauges on

Sent from my SM-N920V using Tapatalk

Looks great. I have stock gauges and will have AEM oil pressure and boost/AFR in mine.

@GaleForce

Love the A Pillar pods...my questions are:

1) How easy are the A pods to remove?
2) Are the OEM ones trashed when they are removed?

I've been eyeing up a dual pod for years, so this may make me finally pull the plug...

Thanks, and yours look amazing...

I'm not Gale, but I can answer your question....

1) Super easy. Just pull on them and they pop loose. There is a plastic tab that will be tethering the pillar to the chassis once it is loose, just reach in with needle nose pliers and turn it 90 degrees to release it. (This will make sense when you see it).

2) Nope.

here's a snap i took a few weeks back. u can see where the tab is located. use an interior tool and pull the very top of the finisher towards the center of the car.

then take a long (quite long) nose pliers and twist the plastic tab. it's there so when the airbag deploys the finisher dont it ur face. :icon17:

http://www.the370z.com/members/kench...ide-driver.jpg

twist (inside red box 90 degrees).
http://www.the370z.com/members/kench...llar-twist.jpg

Thank you Jayhovah and Mr.Kenchan :tiphat:

I second that...thanks for the information and pics :)

Cubby gauge mount received! Looks awesome!!!

I'll try and get the gauges stuffed in and shoot some pictures this week. I'm super busy this week but I'll try and get a quick shot of the mount.

THANKS GALEFORCE!

Some updates,

https://farm2.staticflickr.com/1537/...bfa19cb0_c.jpgInfiniti G37/Q60 pillar - Jeffers by Jason Gale, on Flickr

https://farm2.staticflickr.com/1481/...4945ed42_c.jpgNissan 370Z premium pillar - Scott by Jason Gale, on Flickr

This was a special request. A RHD Premium pillar for a forum member living in Australia. He supplied the photos.

https://farm8.staticflickr.com/7788/...efc444e0_c.jpgAustralia RHD by Jason Gale, on Flickr

Pls pm the price plus shipping to Brunei BE1318
single and double gauge pod for RHD

Thank inadvance

Sent from my HTC One max using Tapatalk

Done :tiphat: