Just swapped the triple meter OEM gauge

JP-370Z · 07-19-2011, 10:16 PM

I went back and forth about how to do this mod... I just could not see adding a gauge pod when I have three perfectly good spots on the dash.

As previously discussed, I don't see anyway you could remove the triple meter without pulling the entire dash. Although I'm certain I could do it, I saw no reason to spend the time to remove all of those pieces to save a $200 gauge that I'll never go through the pain of re-installing. Plus the possibility of introducing a new creak or rattle in the dash because it has now been compromised. Instead I removed the gauge not in one piece but many... I have no use for it so I methodically removed pieces of it one by one eventually reducing it to a plastic pile of rubble in the trash can.

Please excuse the crappy cellphone pics... I did not have a good camera with me at the shop this weekend but i snapped as many photos as I could throughout the process. I will take higher pics of gauges soon.

Removed removed the hoods, cover as well as the plastic covers, faces and needles - all of these will come off with ease.

After about 45 minutes of carefully removing piece by piece...

I was planning to get the Defi gauges after seeing how they looked but had a hard time sourcing them in time to start the project. Turned out better because I decided to go with the ProSport 60mm premium gauges instead which still black out similar to Defi but they also offer wideband O2. I picked up Boost, Oil Temp, Oil Pressure and Wideband AFR ... the boost, oil temp and Widband will go on the dash. The oil pressure will be mounted out of the way but will have an audible alarm and LED indicator on the dash for low pressure indication (separate project on that later)

The size worked out perfect, not too deep and I was able to mill down the OE rings to fit back over for a more stock look. Not entirely stock looking since these have the peak hold/recall button on the face but still very OE finish when all was said and done.

a good bit of dremel work to shave out all of the clips and obstructions to get the gauge to fit properly it fit together perfectly (this is without silver ring at this point)

Complete test assemble of first gauge (not glued together yet though)

Mounting was the next obstacle, I wanted something that would be solid and have zero wiggle room. So cut down a small strip of aluminum for each and with a 3" screw, washer, lock-washer combo arrived at this

test fit / tighten to make sure it worked before creating the others

all three installed

you can source power right from the harness that is feeding the stock gauges. There is ground, constant power and switched ignition power all right there... you can even re-use the other end of the plug that is left over from the stock gauges which met their early demise.

final after install - color matches the stock interior nearly perfect, the iPhone image over saturates the amber glow but it really turned out well.

I took out navi the week before to unplug the the harness that leads to the gauge so that I could be certain that the car did not care that the gauges were no longer present. I would not have been happy to live with any sort of dash board error due to their absence... happy to report that the car does not care about the OEM gauges any more than I did - no errors.

I ran all of the sensor wires through the drivers side firewall and will be making those connection under the hood neatly tucked away under the fluid cover.

.

here is a quick peak at the exterior

sorry I could not post and actual DIY but this should spark some creative ideas and give hope where there previously was none... I will be happy to share any other details you wish

red6spd · 07-19-2011, 10:27 PM

I'm watinggggggggggggggggggggggggggggggggggg

wheee! · 07-19-2011, 10:43 PM

hmmmm.... no implications from the ECU for the missing gauges???

nismo 1234 · 07-19-2011, 10:53 PM

amazing!

chuckd05 · 07-19-2011, 10:58 PM

wow great job... I have a feeling many will be following in your footsteps...

I am confused on how the mount you fabricated holds them in place.. under the hat theres a screw than tightens the aluminum into place to hold them... because the screw in the picture looks like the gauge hat is mangled or cut... is that the case? Or is the gauge hat (or top piece you see from the interior) a seperate piece from the one the screw goes into ?

Cmike2780 · 07-19-2011, 11:01 PM

Very clean, almost stock looking. Nice job.

wheee! · 07-19-2011, 11:03 PM

Well done +1 for you!

JP-370Z · 07-19-2011, 11:06 PM

Quote:

Originally Posted by chuckd05

wow great job... I have a feeling many will be following in your footsteps...

I am confused on how the mount you fabricated holds them in place.. under the hat theres a screw than tightens the aluminum into place to hold them... because the screw in the picture looks like the gauge hat is mangled or cut... is that the case? Or is the gauge hat (or top piece you see from the interior) a seperate piece from the one the screw goes into ?

the hole that i drilled and where you see the screw head is the cover that is UNDER the hat. The hat is not damaged and looks completely stock when all is reassembled.

EazyD · 07-19-2011, 11:08 PM

Killer first post. The gauges look great and are useful. You have a clock on the navi

Not having the guage needles wave at me when I turn the car on is a dealbreaker

FastPaced · 07-19-2011, 11:26 PM

Looks great. I'm loving that Stillen bumper, btw!

BennytheBlade · 07-19-2011, 11:27 PM

I really like the prosport gauges.

EazyD · 07-19-2011, 11:31 PM

Those wheels and front look

JP-370Z · 07-19-2011, 11:41 PM

thank you for the positive feedback guys... I plan to do high res photos of all my mods and post in the appropriate threads but I wanted to share this info about the gauges sooner than later. I'm doing headlight mod now and will begin S/C install this weekend. So far everything is coming together just as planned (knock on wood)

Boost_lee · 07-20-2011, 04:14 AM

To be honest I was a bit worried about the look at the beginning, but the outcome was great. Well done

GingaBreadMan · 07-20-2011, 05:48 AM

The oil temperature is the only usefull gauge we have. What do your replacement gauges show?

07-19-2011, 10:16 PM	#1 (permalink)
JP-370Z Base Member Join Date: May 2011 Location: Atlanta Posts: 12 Drives: '10\|370\|Sport\|6Speed Rep Power: 13	Just swapped the triple meter OEM gauges I went back and forth about how to do this mod... I just could not see adding a gauge pod when I have three perfectly good spots on the dash. As previously discussed, I don't see anyway you could remove the triple meter without pulling the entire dash. Although I'm certain I could do it, I saw no reason to spend the time to remove all of those pieces to save a $200 gauge that I'll never go through the pain of re-installing. Plus the possibility of introducing a new creak or rattle in the dash because it has now been compromised. Instead I removed the gauge not in one piece but many... I have no use for it so I methodically removed pieces of it one by one eventually reducing it to a plastic pile of rubble in the trash can. Please excuse the crappy cellphone pics... I did not have a good camera with me at the shop this weekend but i snapped as many photos as I could throughout the process. I will take higher pics of gauges soon. Removed removed the hoods, cover as well as the plastic covers, faces and needles - all of these will come off with ease. After about 45 minutes of carefully removing piece by piece... I was planning to get the Defi gauges after seeing how they looked but had a hard time sourcing them in time to start the project. Turned out better because I decided to go with the ProSport 60mm premium gauges instead which still black out similar to Defi but they also offer wideband O2. I picked up Boost, Oil Temp, Oil Pressure and Wideband AFR ... the boost, oil temp and Widband will go on the dash. The oil pressure will be mounted out of the way but will have an audible alarm and LED indicator on the dash for low pressure indication (separate project on that later) The size worked out perfect, not too deep and I was able to mill down the OE rings to fit back over for a more stock look. Not entirely stock looking since these have the peak hold/recall button on the face but still very OE finish when all was said and done. a good bit of dremel work to shave out all of the clips and obstructions to get the gauge to fit properly it fit together perfectly (this is without silver ring at this point) Complete test assemble of first gauge (not glued together yet though) Mounting was the next obstacle, I wanted something that would be solid and have zero wiggle room. So cut down a small strip of aluminum for each and with a 3" screw, washer, lock-washer combo arrived at this test fit / tighten to make sure it worked before creating the others all three installed you can source power right from the harness that is feeding the stock gauges. There is ground, constant power and switched ignition power all right there... you can even re-use the other end of the plug that is left over from the stock gauges which met their early demise. final after install - color matches the stock interior nearly perfect, the iPhone image over saturates the amber glow but it really turned out well. I took out navi the week before to unplug the the harness that leads to the gauge so that I could be certain that the car did not care that the gauges were no longer present. I would not have been happy to live with any sort of dash board error due to their absence... happy to report that the car does not care about the OEM gauges any more than I did - no errors. I ran all of the sensor wires through the drivers side firewall and will be making those connection under the hood neatly tucked away under the fluid cover. . here is a quick peak at the exterior sorry I could not post and actual DIY but this should spark some creative ideas and give hope where there previously was none... I will be happy to share any other details you wish .c2, Grantzpitti, exactly and 3 others like this. Last edited by JP-370Z; 07-19-2011 at 11:22 PM.

07-19-2011, 10:27 PM	#2 (permalink)
red6spd A True Z Fanatic Join Date: Apr 2010 Location: Long Island NY Posts: 3,277 Drives: 2010 Z Coupe M6 SPT Rep Power: 21	I'm watinggggggggggggggggggggggggggggggggggg __________________ 2010 Base+Sport 6spd: Stillen G3, FI Non-Resonated CBE, FI Non-Resonated Test Pipes, UpRev Tuned, Custom 24R Oil Cooler, JDM Rear Fog-OEM Harness. ???Whp ???WTQ (Will find out come spring time)

07-19-2011, 10:43 PM	#3 (permalink)
wheee! A True Z Fanatic Join Date: Sep 2009 Location: Mod Capital of Canada Age: 57 Posts: 7,354 Drives: cars. lots of cars. Rep Power: 40181	hmmmm.... no implications from the ECU for the missing gauges??? __________________ H&R / Stillen / Berk / HKS / Swift / Michelin / UpRev / SPC / Amuse Rep / Seibon / Fringe XVO / TWM / more... My Journal

07-19-2011, 10:53 PM	#4 (permalink)
nismo 1234 Track Member Join Date: May 2010 Location: Canada BC Posts: 501 Drives: 10 370z M6 40th Rep Power: 15	amazing! hyunsoo1803 likes this.

07-19-2011, 10:58 PM	#5 (permalink)
chuckd05 A True Z Fanatic Join Date: Oct 2009 Location: NY Posts: 2,391 Drives: No longer a Z Rep Power: 19	wow great job... I have a feeling many will be following in your footsteps... I am confused on how the mount you fabricated holds them in place.. under the hat theres a screw than tightens the aluminum into place to hold them... because the screw in the picture looks like the gauge hat is mangled or cut... is that the case? Or is the gauge hat (or top piece you see from the interior) a seperate piece from the one the screw goes into ? __________________ 09 370Z 6M PW - FBO Best 1/4 mile = 12.926 @ 109 SOLD -- 08 BMW 135i - FBO 12.1@120mph SOLD -- white 09 e92 335 Coupe Mtech - 11.9 @ 119 :-) Last edited by chuckd05; 07-19-2011 at 11:03 PM.

07-19-2011, 11:01 PM	#6 (permalink)
Cmike2780 A True Z Fanatic Join Date: Jun 2010 Location: Long Island Posts: 5,059 Drives: slowwww Rep Power: 28	Very clean, almost stock looking. Nice job. __________________ [09][MB][6-Spd MT][Touring][Stillen Gen III][K&N][Borla CBE][Evo-R] [ArchitTEK Photography]

07-19-2011, 11:03 PM	#7 (permalink)
wheee! A True Z Fanatic Join Date: Sep 2009 Location: Mod Capital of Canada Age: 57 Posts: 7,354 Drives: cars. lots of cars. Rep Power: 40181	Well done +1 for you! __________________ H&R / Stillen / Berk / HKS / Swift / Michelin / UpRev / SPC / Amuse Rep / Seibon / Fringe XVO / TWM / more... My Journal

07-19-2011, 11:08 PM	#9 (permalink)
EazyD A True Z Fanatic Join Date: Nov 2009 Location: Massachusetts, USA Posts: 1,211 Drives: 2010 6MT Sport pkg. Rep Power: 25	Killer first post. The gauges look great and are useful. You have a clock on the navi Not having the guage needles wave at me when I turn the car on is a dealbreaker __________________ Pearl White 2010 370Z Sport, Stillen CBE, tint, K&N drop-in filters, GT-R start button, Kenwood DNX-6980 with backup cam, LED bulbs, Raceseng shift knob.

07-19-2011, 11:26 PM	#10 (permalink)
FastPaced Enthusiast Member Join Date: Mar 2011 Location: Bronx, NY Posts: 372 Drives: '08 SFP IS-F Rep Power: 14	Looks great. I'm loving that Stillen bumper, btw!

07-19-2011, 11:27 PM	#11 (permalink)
BennytheBlade Base Member Join Date: Oct 2009 Location: Huntsville Posts: 180 Drives: 09 Black 370 NISMO Rep Power: 15	I really like the prosport gauges. __________________ Forged Specialties SC 6 Bronze 19x9.5 +22 19x10.5+12\|Hankook Evo 255/35/19 305/30/19 Berk HFC \| BM Short Shifter \|Stillen G3 Intake

07-19-2011, 11:31 PM	#12 (permalink)
EazyD A True Z Fanatic Join Date: Nov 2009 Location: Massachusetts, USA Posts: 1,211 Drives: 2010 6MT Sport pkg. Rep Power: 25	Those wheels and front look __________________ Pearl White 2010 370Z Sport, Stillen CBE, tint, K&N drop-in filters, GT-R start button, Kenwood DNX-6980 with backup cam, LED bulbs, Raceseng shift knob.

07-19-2011, 11:41 PM	#13 (permalink)
JP-370Z Base Member Join Date: May 2011 Location: Atlanta Posts: 12 Drives: '10\|370\|Sport\|6Speed Rep Power: 13	thank you for the positive feedback guys... I plan to do high res photos of all my mods and post in the appropriate threads but I wanted to share this info about the gauges sooner than later. I'm doing headlight mod now and will begin S/C install this weekend. So far everything is coming together just as planned (knock on wood) Boomzig likes this.

07-20-2011, 04:14 AM	#14 (permalink)
Boost_lee A True Z Fanatic Join Date: Feb 2009 Location: SATX Posts: 2,813 Drives: 09 370Z TT 6MT Rep Power: 29	To be honest I was a bit worried about the look at the beginning, but the outcome was great. Well done __________________ My TT Z

07-20-2011, 05:48 AM	#15 (permalink)
GingaBreadMan Enthusiast Member Join Date: Jun 2009 Location: New York Posts: 313 Drives: 09 370z Sport 6spd Rep Power: 15	The oil temperature is the only usefull gauge we have. What do your replacement gauges show? __________________ ClearBra/Debadging/Tinted Head & Taillights Coming Soon:180° Customs Headlights/ISS Forged Spyder 19" 265*305/Swift Springs/STS Rear Mount Turbo

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Who has swapped to the 4.08 gear?	Big J	Engine & Drivetrain	16	11-27-2012 02:21 PM
triple gauge covers	soldknow	Exterior & Interior	5	01-30-2011 12:03 PM
Custom triple meter modification...	DIGItonium	Exterior & Interior	23	11-18-2010 04:07 PM
370z Nismo version instrument meter & gauge	deben	Exterior & Interior	0	10-01-2010 09:51 AM
Tsb: 2009-2010 nissan 370z coupe, 370z roadster; triple meter clock setting procedure	AK370Z	370Z Technical Service Bulletins (TSB) / Recalls	0	02-08-2010 10:21 PM