No start, but cranks

Joepro · 04-24-2014, 05:29 PM

Got it out...

Joepro · 04-24-2014, 06:04 PM

picture from courtesy parts...

1slow370 · 04-24-2014, 06:36 PM

yeah thats F'd, that is F'd right up. now you get to try and figure out why the trigger ring is F'ing your' crank sensor right in the A or it will do it again.

Joepro · 04-24-2014, 06:49 PM

my cousin seemed to think it is heat related...the flywheel has been on the car for 15k...southbend alm fly.

1slow370 · 04-24-2014, 06:55 PM

the groove in the sensor looks thinner than the teeth on that flywheel damage could have been from your oem one before you switched and it just finally gave out. just in case check the teeth on the flywheel for wear marks maybe one of the teeth has a burr on it. you might be able to see through the crank sensor hole or the inspection window on the bottom of the trans. otherwise take the old sensor and put a couple layers o tape on the tip and shove it back in, then turn the engine over take it out and see if your tape is still in one piece.

Chuck33079 · 04-24-2014, 06:59 PM

Could it be related to your clutch/flywheel failure?

Joepro · 04-24-2014, 07:04 PM

I doubt it has anything to do with the plate failure, I wish I would have looked at the sensor while the trans was out...the teeth on the southbend flywheel are thin to my recollection, there is not a chance I could see down the hole...maybe I should try to put a washer where it bolts in, just a small copper crush one like a drain plug gasket, should move it away enough and still read, just so I can drive it to the shop to lift it and look through the check plate.

Joepro · 04-24-2014, 07:14 PM

tough to see in this pic but you can see the difference in the teeth.

1slow370 · 04-24-2014, 07:32 PM

ah i was looking at their race steel flywheels those have bigger teeth. In that case it it very possible that your southbend struck again. OS Giken bro, OS Giken (and I normally hate over priced JDM chit but this thing one me over)

Joepro · 04-24-2014, 07:45 PM

I think ill put a washer on it for now, see if it works. I will also inspect closely the new sensor vs the old to see if there is any differences.

black_sedan · 04-25-2014, 05:40 PM

So whats the verdict?

Sucks that you're having all those problems. Just a few weeks ago, I was reading your thread when your clutch started making all sorts of funny noises.

Got my fingers crossed that its something simple.

Chuck33079 · 04-25-2014, 05:41 PM

Quote:

Originally Posted by black_sedan

Just a few weeks ago, I was reading your thread when your clutch started making all sorts of funny noises.

Got my fingers crossed that its something simple.

That's why I still think it's all somehow related. If not, it's one hell of a coincidence.

Joepro · 04-25-2014, 06:05 PM

Verdict is life hates my azz. There is now undoubtedly an issue with the pickup teeth on the flywheel. I installed the new sensor with a small copper washer and the car would spudder but would not start. So I took the washer off, and the car fired right up, but I shut it off seconds later because I could HEAR the ring grinding the plastic off the new sensor, JFC. I ran back to work and the techs had some really thin shims, 4 equaled the copper washer, I pulled the sensor, which now has a slight groove in it, and put three shims on, and the car starts and runs poorly, but I cannot hear the teeth grinding the sensor. At this point the headers were too hot for me to reach back in there. Tomorrow after work I will remove a shim and then drive it over and park it at the shop, which is less than a mile. Monday ill get it on a rack and pull the check plate to see if I can visually see any issues, regardless it sounds as if the trans is coming out AGAIN. I really do not want to drop 2k on a OS Giken twin disk, Shane at work has a clutch masters twin in his 550 whp neon and it drives like $%^& on the street...Im not sure the JWT is up to the task of holding this power...I ran ACT in my 350z with no issues, I might see what they have to offer. This is getting stupid.

Chuck33079 · 04-25-2014, 06:07 PM

OS Giken Twin Plate Grand Touring Clutch

Hell of a price.

jwick · 04-25-2014, 06:07 PM

Quote:

Originally Posted by Joepro

Verdict is life hates my azz. There is now undoubtedly an issue with the pickup teeth on the flywheel. I installed a the new sensor with a small copper washer and the car would spudder but would not start. So I took the washer off, and the car fired right up, but I shut it off seconds later because I cout HEAR the ring grinding the plastic off the new sensor, JFC. I ran back to work and the techs had so really thin shims, 4 equaled the copper washer, I pulled the sensor, which now has a slight groove in it, and put three shims on, and the car starts and runs poorly, but I cannot hear the teeth grinding the sensor. At this point the headers were too hot for me to reach back in there. Tomorrow after work I will remove a shim and then drive it over and park it at the shop, which is less than a mile. Monday ill get it on a rack and pull the check plate to see if I can visually see any issues, regardless it sounds as if the trans is coming out AGAIN. I really do not want to drop 2k on a OS Giken twin disk, Shane at work has a clutch masters twin in his 550 whp neon and it drives like $%^& on the street...Im not sure the JWT is up to the task of holding this power...I ran ACT in my 350z with no issues, I might see what they have to offer. This is getting stupid.

I'm running Z1 full face and light weight fly wheel. Held up just fine on the dyno today with a bunch of torque

04-24-2014, 05:29 PM	#61 (permalink)
Joepro A True Z Fanatic Join Date: Aug 2012 Location: Athens ohio Posts: 1,213 Drives: Company car Rep Power: 33	Got it out... __________________ Swift\|Koni\|SPC\| FI CBE\|Z1\|Stillen\|Sbend\|Zspeed\|R/T Tuned\|523 whp\|458 tq\|10.5 psi\|SOLD Joepro's Journal\|Joepro's Boosted Performance Build \|Pittsburgh-Western-Pa-Ohio-Wv-Group

04-24-2014, 06:04 PM	#62 (permalink)
Joepro A True Z Fanatic Join Date: Aug 2012 Location: Athens ohio Posts: 1,213 Drives: Company car Rep Power: 33	picture from courtesy parts... __________________ Swift\|Koni\|SPC\| FI CBE\|Z1\|Stillen\|Sbend\|Zspeed\|R/T Tuned\|523 whp\|458 tq\|10.5 psi\|SOLD Joepro's Journal\|Joepro's Boosted Performance Build \|Pittsburgh-Western-Pa-Ohio-Wv-Group

04-24-2014, 06:36 PM	#63 (permalink)
1slow370 A True Z Fanatic Join Date: Aug 2009 Location: In the D Posts: 3,732 Drives: v8 74 260z ;) Rep Power: 7250	yeah thats F'd, that is F'd right up. now you get to try and figure out why the trigger ring is F'ing your' crank sensor right in the A or it will do it again. __________________ ANSWER PRICE LIST Answers - - - - - - - - - - - - - - - - $0.75 Answers (requiring thought) - - - - $1.25 Answers (correct) - - - - - - - - - - $12.50

04-24-2014, 06:49 PM	#64 (permalink)
Joepro A True Z Fanatic Join Date: Aug 2012 Location: Athens ohio Posts: 1,213 Drives: Company car Rep Power: 33	my cousin seemed to think it is heat related...the flywheel has been on the car for 15k...southbend alm fly. __________________ Swift\|Koni\|SPC\| FI CBE\|Z1\|Stillen\|Sbend\|Zspeed\|R/T Tuned\|523 whp\|458 tq\|10.5 psi\|SOLD Joepro's Journal\|Joepro's Boosted Performance Build \|Pittsburgh-Western-Pa-Ohio-Wv-Group

04-24-2014, 06:55 PM	#65 (permalink)
1slow370 A True Z Fanatic Join Date: Aug 2009 Location: In the D Posts: 3,732 Drives: v8 74 260z ;) Rep Power: 7250	the groove in the sensor looks thinner than the teeth on that flywheel damage could have been from your oem one before you switched and it just finally gave out. just in case check the teeth on the flywheel for wear marks maybe one of the teeth has a burr on it. you might be able to see through the crank sensor hole or the inspection window on the bottom of the trans. otherwise take the old sensor and put a couple layers o tape on the tip and shove it back in, then turn the engine over take it out and see if your tape is still in one piece. __________________ ANSWER PRICE LIST Answers - - - - - - - - - - - - - - - - $0.75 Answers (requiring thought) - - - - $1.25 Answers (correct) - - - - - - - - - - $12.50

04-24-2014, 06:59 PM	#66 (permalink)
Chuck33079 A True Z Fanatic Join Date: Nov 2011 Location: Houston Posts: 12,265 Drives: 2011 370ztt Rep Power: 29538	Could it be related to your clutch/flywheel failure? __________________ 2011 MB Touring-Sport-6sp-Nav/GTM TT/FI TT TDX/JTran/Kosmic/Eibach/Hotchkis/SPC/CSF/RPS/SoThatsWhereAllMyMoneyWent

04-24-2014, 07:04 PM	#67 (permalink)
Joepro A True Z Fanatic Join Date: Aug 2012 Location: Athens ohio Posts: 1,213 Drives: Company car Rep Power: 33	I doubt it has anything to do with the plate failure, I wish I would have looked at the sensor while the trans was out...the teeth on the southbend flywheel are thin to my recollection, there is not a chance I could see down the hole...maybe I should try to put a washer where it bolts in, just a small copper crush one like a drain plug gasket, should move it away enough and still read, just so I can drive it to the shop to lift it and look through the check plate. __________________ Swift\|Koni\|SPC\| FI CBE\|Z1\|Stillen\|Sbend\|Zspeed\|R/T Tuned\|523 whp\|458 tq\|10.5 psi\|SOLD Joepro's Journal\|Joepro's Boosted Performance Build \|Pittsburgh-Western-Pa-Ohio-Wv-Group

04-24-2014, 07:14 PM	#68 (permalink)
Joepro A True Z Fanatic Join Date: Aug 2012 Location: Athens ohio Posts: 1,213 Drives: Company car Rep Power: 33	tough to see in this pic but you can see the difference in the teeth. __________________ Swift\|Koni\|SPC\| FI CBE\|Z1\|Stillen\|Sbend\|Zspeed\|R/T Tuned\|523 whp\|458 tq\|10.5 psi\|SOLD Joepro's Journal\|Joepro's Boosted Performance Build \|Pittsburgh-Western-Pa-Ohio-Wv-Group

04-24-2014, 07:32 PM	#69 (permalink)
1slow370 A True Z Fanatic Join Date: Aug 2009 Location: In the D Posts: 3,732 Drives: v8 74 260z ;) Rep Power: 7250	ah i was looking at their race steel flywheels those have bigger teeth. In that case it it very possible that your southbend struck again. OS Giken bro, OS Giken (and I normally hate over priced JDM chit but this thing one me over) __________________ ANSWER PRICE LIST Answers - - - - - - - - - - - - - - - - $0.75 Answers (requiring thought) - - - - $1.25 Answers (correct) - - - - - - - - - - $12.50

04-24-2014, 07:45 PM	#70 (permalink)
Joepro A True Z Fanatic Join Date: Aug 2012 Location: Athens ohio Posts: 1,213 Drives: Company car Rep Power: 33	I think ill put a washer on it for now, see if it works. I will also inspect closely the new sensor vs the old to see if there is any differences. __________________ Swift\|Koni\|SPC\| FI CBE\|Z1\|Stillen\|Sbend\|Zspeed\|R/T Tuned\|523 whp\|458 tq\|10.5 psi\|SOLD Joepro's Journal\|Joepro's Boosted Performance Build \|Pittsburgh-Western-Pa-Ohio-Wv-Group

04-25-2014, 05:40 PM	#71 (permalink)
black_sedan Enthusiast Member Join Date: Dec 2011 Location: Florida Posts: 308 Drives: 14' F150, 14' Q50 Rep Power: 13	So whats the verdict? Sucks that you're having all those problems. Just a few weeks ago, I was reading your thread when your clutch started making all sorts of funny noises. Got my fingers crossed that its something simple.

04-25-2014, 06:05 PM	#73 (permalink)
Joepro A True Z Fanatic Join Date: Aug 2012 Location: Athens ohio Posts: 1,213 Drives: Company car Rep Power: 33	Verdict is life hates my azz. There is now undoubtedly an issue with the pickup teeth on the flywheel. I installed the new sensor with a small copper washer and the car would spudder but would not start. So I took the washer off, and the car fired right up, but I shut it off seconds later because I could HEAR the ring grinding the plastic off the new sensor, JFC. I ran back to work and the techs had some really thin shims, 4 equaled the copper washer, I pulled the sensor, which now has a slight groove in it, and put three shims on, and the car starts and runs poorly, but I cannot hear the teeth grinding the sensor. At this point the headers were too hot for me to reach back in there. Tomorrow after work I will remove a shim and then drive it over and park it at the shop, which is less than a mile. Monday ill get it on a rack and pull the check plate to see if I can visually see any issues, regardless it sounds as if the trans is coming out AGAIN. I really do not want to drop 2k on a OS Giken twin disk, Shane at work has a clutch masters twin in his 550 whp neon and it drives like $%^& on the street...Im not sure the JWT is up to the task of holding this power...I ran ACT in my 350z with no issues, I might see what they have to offer. This is getting stupid. __________________ Swift\|Koni\|SPC\| FI CBE\|Z1\|Stillen\|Sbend\|Zspeed\|R/T Tuned\|523 whp\|458 tq\|10.5 psi\|SOLD Joepro's Journal\|Joepro's Boosted Performance Build \|Pittsburgh-Western-Pa-Ohio-Wv-Group Last edited by Joepro; 04-25-2014 at 06:11 PM.

04-25-2014, 06:07 PM	#74 (permalink)
Chuck33079 A True Z Fanatic Join Date: Nov 2011 Location: Houston Posts: 12,265 Drives: 2011 370ztt Rep Power: 29538	OS Giken Twin Plate Grand Touring Clutch Hell of a price. Optimiser likes this. __________________ 2011 MB Touring-Sport-6sp-Nav/GTM TT/FI TT TDX/JTran/Kosmic/Eibach/Hotchkis/SPC/CSF/RPS/SoThatsWhereAllMyMoneyWent

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
370z wont start no power . Where to start	acracing118	Exterior & Interior	6	01-05-2013 06:37 PM
Car will start sometimes and not start, need advice	aragona7	Nissan 370Z General Discussions	11	03-08-2012 10:23 PM
If you had to start all over....	saiko71	Forced Induction	31	03-27-2011 08:56 PM
cold start/push start	chops	Nissan 370Z General Discussions	21	02-14-2011 03:40 AM
HELP: Car won't start!	tjlazer	Engine & Drivetrain	41	04-06-2010 02:21 PM