OEM oil cooler removal with aftermarket?

synolimit · 01-24-2014, 06:53 AM

Quote:

Originally Posted by Tigger

I'll throw my two cents in on this right quick even though it is a slightly old topic it may help others.

First. The stock 12+ MY oil cooler works fine. I have beaten my 370 down and even in summer temps it never went past 230.

Second. And I've spoken with the dealer regarding a retro-fit of the stock oil cooler assembly on a pre-12 MY 370 and the cost was pushing $900 just for parts. And the complexity of installing it is a bit over the top since you would need to drop the motor. Yes. You need to drop the motor.

Third. I had a 25R GTM oil cooler installed on top of the stock oil cooler and ran into over-cooling issues. It was subsequently removed within two weeks. Oil temps are back to ideal. (The needle on the dash isn't exactly what your oil temps really are but we should all know this by now)

Not to mention the holes you get to cut and the minor modifications to the mount to fit the cooler, rubbing issues with lines, extra hardware to fall apart on you. And the best part? If this thing fails and your motor goes you get to foot the bill on a replacement motor if it is under warranty.

Given that little tidbit... Why even bother with it? If it is under warranty and you don't go into limp mode (as you shouldn't), why try to overdo it? It is a waste of money and in the end can be more detrimental by causing sludge formation due to moisture in the oil not burning off because it isn't getting hot enough.

Anyhow... Those are my thoughts after having been through this already. Take it or leave it. Good luck!

No it doesn't, you must not drive hard enough or on the track. Everyone over heats with it, period.

Who the hell asks a dealer for anything? I have no idea what the **** you're even smoking if you agree with them that "yes you need to drop the motor." Don't reinvent the wheel. Install an oil cooler like normal people do.

Won't over cool with a block off plate. I get the feeling you're a very over cautious person. Never heard of the oil gauge being off. In fact most people that have said what limp mode is within the ecu have also stated that's what the gauge says when said limp mode occurs.

Lol holes? That one tiny 2.5" hole to much for you? Or you could just remove that little flap of plastic and no holes then. This is a track thread my friend, I should move it to the track thread to call you a troll. Mods to the mount? You bolt a plate down, big deal! Rubbing won't happen if you have a brain. There's lots of OEM lines, they don't rub do they? Not sure how one oil cooler would fail (you do know these are on tons of factory cars don't you??!) if again you have a brain at installing. Tons and tons of people for years have been doing these and not only on these cars.

You do it so you don't over heat and cook the motors oil. Did that real need explaining? i don't even want to go on. Tons of fail my friend, good day.

View Poll Results: OEM oil cooler remove?
Remove OEM oil cooler is a good idea. More room, less weight.	19	47.50%
Leave it with the aftermarket cooler for better results.	21	52.50%
Voters: 40. You may not vote on this poll

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Aftermarket Oil Cooler Ruining A/C Temps?	Crxckadome	Engine & Drivetrain	11	06-02-2013 11:16 AM
Aftermarket oil cooler in CS?	fastguy9r	Track / Autocross / Drifting / Dragstrip	8	03-11-2013 07:51 PM
Aftermarket Z parts- Oil Cooler, Long Tube Headers, etc. in Fremont	VICTOR	Northern California Region	1	01-30-2012 11:42 AM
[WTB] WTB Aftermarket Oil Cooler ASAP	krod	Parts for sale (Private Classifieds)	4	12-17-2011 08:35 AM
Aftermarket Oil Cooler Question for SC Z's	krod	Forced Induction	9	11-08-2011 01:26 PM