Oil Temperature Issues

EventHorizoN · 07-25-2011, 12:42 PM

Hello Fellow Z Car owners,

Just recently I purchased the Z1 Motorsports 370Z Oil Cooler Kit.

The kit includes:
# 1x Setrab Oil Cooler Core (19 Row Standard; Additional sizes available)
# 1x Z1 -10 AN SS Oil Cooler Line Set (Optional protective sleeving available pre-installed)
# 1x Mocal Sandwich Adapter (Non-Thermostatic Standard; Optional Thermostatic model available)
# 1x Setrab Oil Cooler Lower Mount
# 1x Z1 Motorsports Oil Cooler Upper Mount
# 1x Z1 Motorsports 370Z Oil Cooler Install Hardware Kit
# 1x Z1 Motorsports 370Z Oil Cooler Installation Instructions
# 2x Setrab (-10 AN to 22mm Port) adapter fittings (Cooler)
# 2x Mocal (-10 AN to 22mm Port) adapter fittings (Sandwich adapter)
# 2x 13/16" Rubber Seal (Sandwich Adapter)

Some friends and I recently installed the same kit on my good friends 2010 370z. It works amazing on his car both on the street and on the track.

However, with mine its not the case. This past weekend I went to Streets of Willow and had some serious Oil Temp issues even with the Cooler installed. I know its working because I never have a rise above 180 degrees driving on the public roads. Yet, when I started driving on the track the temps jumped from 180 all the way to 260+ Thus making the car go into limp mode. Basically the car was running the same as when the Oil Cooler wasn't installed. Which makes no sense when my friends is working properly with heavy tracking.

Does anyone else have this problem, and if so what measures should I take to resolve this immediately! Thank you all in advance, and looking forward to hearing everyone's feedback!

Thank you!

Jason

cossie1600 · 07-25-2011, 12:50 PM

You are in south cal, the 19R might be too small for you. Short shift by 500RPM, that will help lower the temperature for the short term.

EventHorizoN · 07-25-2011, 01:02 PM

Quote:

Originally Posted by cossie1600

You are in south cal, the 19R might be too small for you. Short shift by 500RPM, that will help lower the temperature for the short term.

Thanks for the quick response, it's much appreciated. I was just thinking the same thing, now I am seriously considering upgrading to the 25row core. A good friend of mine also asked me what my RPM range was while tracking. I think running the RPM's high will definitely increase the temperatures. I'm just hoping my car doesn't have a serious issue. We are going to Streets of Willow again this coming weekend, I really hope I don't run into the same problem again...

WWJD · 07-25-2011, 01:23 PM

Hi Jason, hope u can get your problem solved. U might wanna change or get your car checked out before going to track. This weekend will be hotter than the night event.
This is Ricky btw.

Trips · 07-25-2011, 01:23 PM

Quote:

Originally Posted by EventHorizoN

Thanks for the quick response, it's much appreciated. I was just thinking the same thing, now I am seriously considering upgrading to the 25row core. A good friend of mine also asked me what my RPM range was while tracking. I think running the RPM's high will definitely increase the temperatures. I'm just hoping my car doesn't have a serious issue. We are going to Streets of Willow again this coming weekend, I really hope I don't run into the same problem again...

Id just go with a 34 row and call it a day

I've been on the canyons on 90+ days and have not had any issues with oil temps.

gtkiller · 07-25-2011, 01:39 PM

It's odd that we both have the same oil cooler and I did not have the same issues at the track. I was running a little above 230-240 car felt great all day. Of course I don't have any bolt on mods.
BTW this is walter

red6spd · 07-25-2011, 01:49 PM

Yea 19 is to small. The standard should be at least 24 25 row. I run a 24.

WWJD · 07-25-2011, 02:45 PM

^^There's another car running exact the same oil cooler that had no issue whatsoever. If 19 is too small, then how come the guy has the same cooler could run all day long without overheating?

zcar_dad · 07-25-2011, 02:50 PM

Quote:

Originally Posted by WWJD

^^There's another car running exact the same oil cooler that had no issue whatsoever. If 19 is too small, then how come the guy has the same cooler could run all day long without overheating?

What did Z1 tell you when you called them?

Mike · 07-25-2011, 02:56 PM

Quote:

Originally Posted by WWJD

^^There's another car running exact the same oil cooler that had no issue whatsoever. If 19 is too small, then how come the guy has the same cooler could run all day long without overheating?

but were they running the same lap times? The harder you drive, the hotter the oil. Just like fuel starvation. Novices on stock tires get it around 1/2 tank or less, more advanced drivers on sticky tires get it before hitting 7/8 of a tank.

WWJD · 07-25-2011, 03:03 PM

Quote:

Originally Posted by Mike

but were they running the same lap times? The harder you drive, the hotter the oil. Just like fuel starvation. Novices on stock tires get it around 1/2 tank or less, more advanced drivers on sticky tires get it before hitting 7/8 of a tank.

The op couldn't even run 4 laps straight. I don't think he ran hard enough to make the difference.
My guess is the oil cooler or hose or some hardware problems.
Also, I drove an Z with the same cooler set up for 20 min straight in 100+ F hot day. No issue.

Dustin@Z1 · 07-25-2011, 03:16 PM

Jason,
For a track'ed Z, we recommend atleast a 25 row core. In your case, given your local, I would even go so far as suggesting a 34 Row core if you plan on doing repeated track events. I hate that you had an issue with your Z.

Did you speak with anyone here at Z1 prior to you making your purchase? Let me know if you decide to upgrade to a larger core. I will do what I can to get you the best price shipped so that you can make the track this weekend. I have both 25 and 34 Row Cores instock and can ship today. Via standard ground service I can get you a core by Thursday/Friday without requiring any expedited shipping.

Dustin@Z1 · 07-25-2011, 03:21 PM

Quote:

Originally Posted by WWJD

^^There's another car running exact the same oil cooler that had no issue whatsoever. If 19 is too small, then how come the guy has the same cooler could run all day long without overheating?

Was it one of our kits? I would be VERY impressed to hear about this! Are you sure it was a 6 series 19 row? Or was it a 9 series 19 row core?

The 6 series 19 row is very small in comparison to a 9 series 19 row. A 9 series 19 row will have a similar surface area as a 6 series 25 row oil cooler core.

travisjb · 07-25-2011, 03:37 PM

Dustin, you guys might think about offering a duct kit that directs airflow from the OEM front fascia to the core... using that setup, I've been able to run summer events in Arizona with only one setrab core... I'd guess it saved me ~20F. Mike B is also running this setup. Another thing you might consider is to reduce the gap between the oil cooler core and the radiator - I was told by some racing buds in AZ that a smaller gap there will make the leading core more efficient because it will help pull air through... no science to back that up, of course, so take it with a grain of salt

OP, you can mock up your own air flow duct/diverter to this core and try that as a next step... just go to ace hardware and buy some thin sheets of aluminum, cut to fit and mount up using rivets or frankly duct tape + velcro... the goal is to build a "box" leading up to the core so air has to go through the core and can't get around it

EventHorizoN · 07-25-2011, 03:48 PM

Quote:

Originally Posted by WWJD

Hi Jason, hope u can get your problem solved. U might wanna change or get your car checked out before going to track. This weekend will be hotter than the night event.
This is Ricky btw.

Thank you very much Ricky!I need to take care of this asap... especially for next weekend! Btw: your going to be coming out this coming Saturday right?
I posted some photos of your GT-R on my flickr! Enjoy friend!
Flickr: d3capmode's Photostream

Jason

07-25-2011, 01:23 PM	#4 (permalink)
WWJD Enthusiast Member Join Date: Jun 2010 Location: SoCal Posts: 396 Drives: PW 370Z Rep Power: 16	Hi Jason, hope u can get your problem solved. U might wanna change or get your car checked out before going to track. This weekend will be hotter than the night event. This is Ricky btw. __________________ My Journal #1 My Journal #2 Build by The R's Tuning, Irvine Laguna Seca 1:43.073 (stock power)/ Buttonwillow 13CW 1:59.532 (full exhaust)

07-25-2011, 01:49 PM	#7 (permalink)
red6spd A True Z Fanatic Join Date: Apr 2010 Location: Long Island NY Posts: 3,277 Drives: 2010 Z Coupe M6 SPT Rep Power: 22	Yea 19 is to small. The standard should be at least 24 25 row. I run a 24. __________________ 2010 Base+Sport 6spd: Stillen G3, FI Non-Resonated CBE, FI Non-Resonated Test Pipes, UpRev Tuned, Custom 24R Oil Cooler, JDM Rear Fog-OEM Harness. ???Whp ???WTQ (Will find out come spring time)

07-25-2011, 02:45 PM	#8 (permalink)
WWJD Enthusiast Member Join Date: Jun 2010 Location: SoCal Posts: 396 Drives: PW 370Z Rep Power: 16	^^There's another car running exact the same oil cooler that had no issue whatsoever. If 19 is too small, then how come the guy has the same cooler could run all day long without overheating? __________________ My Journal #1 My Journal #2 Build by The R's Tuning, Irvine Laguna Seca 1:43.073 (stock power)/ Buttonwillow 13CW 1:59.532 (full exhaust)

07-25-2011, 03:37 PM	#14 (permalink)
travisjb A True Z Fanatic Join Date: Jan 2009 Location: GSO Posts: 2,803 Drives: VIR Rep Power: 189	Dustin, you guys might think about offering a duct kit that directs airflow from the OEM front fascia to the core... using that setup, I've been able to run summer events in Arizona with only one setrab core... I'd guess it saved me ~20F. Mike B is also running this setup. Another thing you might consider is to reduce the gap between the oil cooler core and the radiator - I was told by some racing buds in AZ that a smaller gap there will make the leading core more efficient because it will help pull air through... no science to back that up, of course, so take it with a grain of salt OP, you can mock up your own air flow duct/diverter to this core and try that as a next step... just go to ace hardware and buy some thin sheets of aluminum, cut to fit and mount up using rivets or frankly duct tape + velcro... the goal is to build a "box" leading up to the core so air has to go through the core and can't get around it __________________ 2009 370Z #104 For Sale

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Outside air temperature gauge	Parrotguy	Exterior & Interior	6	03-09-2011 10:07 PM
thinking of buying 370z, then GTM turbo's , but overheat issues,oil issues ??	Christopher	Nissan 370Z General Discussions	19	10-16-2009 03:55 PM
Initial Z issues that are now non-issues......	cave vulture	Nissan 370Z General Discussions	1	09-06-2009 10:19 PM
Oil Temperature Video	Vectorsumio	Nissan 370Z Photos / Spyshots / Video / Media Gallery	39	08-27-2009 06:29 PM
Outside temperature gauge.	Chan Chee Hoe	Nissan 370Z General Discussions	12	05-11-2009 06:15 PM

07-25-2011, 12:50 PM	#2 (permalink)
cossie1600 A True Z Fanatic Join Date: Jun 2009 Location: californee way Posts: 5,380 Drives: 370, Leaf Rep Power: 31	You are in south cal, the 19R might be too small for you. Short shift by 500RPM, that will help lower the temperature for the short term.

07-25-2011, 01:39 PM	#6 (permalink)
gtkiller Enthusiast Member Join Date: Jul 2010 Location: SoCal Posts: 489 Drives: 370Z Rep Power: 3371	It's odd that we both have the same oil cooler and I did not have the same issues at the track. I was running a little above 230-240 car felt great all day. Of course I don't have any bolt on mods. BTW this is walter

07-25-2011, 03:16 PM	#12 (permalink)
Dustin@Z1 The370Z.com Sponsor Join Date: Jun 2009 Location: NLA Posts: 1,313 Drives: NLA Rep Power: 19	Jason, For a track'ed Z, we recommend atleast a 25 row core. In your case, given your local, I would even go so far as suggesting a 34 Row core if you plan on doing repeated track events. I hate that you had an issue with your Z. Did you speak with anyone here at Z1 prior to you making your purchase? Let me know if you decide to upgrade to a larger core. I will do what I can to get you the best price shipped so that you can make the track this weekend. I have both 25 and 34 Row Cores instock and can ship today. Via standard ground service I can get you a core by Thursday/Friday without requiring any expedited shipping.