Engine Ticking Noise Rythmic

Spooler · 09-13-2018, 02:47 PM

Yeap, Galley gasket has failed.

Jordan12berg · 09-14-2018, 06:51 PM

Any pro tips on this oil pan? I can’t even get a razor blade to the glue

Rusty · 09-14-2018, 07:39 PM

All the bolts out? If so, put one back on each side. Just a couple of threads screwed in. When the pan pops loose. This keeps the pan in place and not making a mess of things.

I've used a wood chisel at the split line and tapped it in with a hammer. After cleaning up the split line. If there is any marks or gouges. I use a fine file to file down the raised area. Just be careful.

Jordan12berg · 09-14-2018, 08:01 PM

I had all the screws removed originally, I can put a few screws in. The problem is I I have even but a razor blade on a handle and slightly tapped it in and It won’t even let the razor in. It’s so tight at the split line.

Jordan12berg · 09-14-2018, 08:09 PM

This is what I’m working with

Jordan12berg · 09-14-2018, 08:56 PM

Got it!

And 125xxx miles, blown gasket, still no metal shavings at the bottom of the pan or the magnetic plug

Jordan12berg · 09-17-2018, 08:11 PM

Great these bolts for the galley gaskets, the 4mm hex bolts, are starting to strip before I get them to 12ftlbs. I put loctite on them.

Rusty · 09-17-2018, 08:24 PM

You putting it back together again? How bad was the gaskets?

Yeah, sometimes those small bolts don't have enough head on them for a good bite.

Jordan12berg · 09-17-2018, 08:30 PM

Yea finally, they were pretty much exploded on the sideways Y piece.

So my torque wrench can’t even torque down to 12 before they strip. It’s close but it won’t click before they give. I got loctite on them am I going to be ok?

Rusty · 09-17-2018, 09:49 PM

Quote:

Originally Posted by Jordan12berg

Yea finally, they were pretty much exploded on the sideways Y piece.

So my torque wrench can’t even torque down to 12 before they strip. It’s close but it won’t click before they give. I got loctite on them am I going to be ok?

Is the torque wrench in in.lbs or ft.lbs? A 4mm diameter would be in, in.lbs. If your torque wrench is in, ft lbs. And you are torquing to that. 12 ft.lbs is 144 in.lbs.

Jordan12berg · 09-18-2018, 02:23 PM

Haha torque wrench is in ft lbs. I have a hex tool set with a 3/8 connection set I was using.
But yea I followed this DIY: 370z Oil Galley #9 says 12 ft lbs and I dug up all bolt orders and tq specs in the fsm.

Rusty · 09-18-2018, 03:27 PM

Quote:

Originally Posted by Jordan12berg

Haha torque wrench is in ft lbs. I have a hex tool set with a 3/8 connection set I was using.
But yea I followed this DIY: 370z Oil Galley #9 says 12 ft lbs and I dug up all bolt orders and tq specs in the fsm.

I read the thread. Yeah, it says 12 ft.lbs. I see where it's a 4mm allen. Not a 4mm diameter bolt. Big difference between the 2.

Spooler · 09-18-2018, 06:54 PM

Doesn't someone make upgraded bolts that can be torqued properly? I am not sure who makes them, that's what is going on my car.
Do a search, it is on here somewhere. The bolts and gaskets are upgraded.

Rusty · 09-18-2018, 07:51 PM

Quote:

Originally Posted by Spooler

Doesn't someone make upgraded bolts that can be torqued properly? I am not sure who makes them, that's what is going on my car.
Do a search, it is on here somewhere. The bolts and gaskets are upgraded.

It's a steel bolt threading into aluminum hole. Don't think the issue is with the bolt, it's with the hole. If this is happening. The fix would be to heli-coil the hole.

Pic from the DIY thread.

Jordan12berg · 09-18-2018, 09:44 PM

So they are definitely more than hand right with loctite, I should be good right?

And these are the “upgraded bolts” from concept Z
And looking at the DIY pictures it looks like they stripped on them as well.

09-14-2018, 07:39 PM	#48 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 69 Posts: 35,514 Drives: 2011 Nismo GM 6M Rep Power: 2684439	All the bolts out? If so, put one back on each side. Just a couple of threads screwed in. When the pan pops loose. This keeps the pan in place and not making a mess of things. I've used a wood chisel at the split line and tapped it in with a hammer. After cleaning up the split line. If there is any marks or gouges. I use a fine file to file down the raised area. Just be careful. __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

09-14-2018, 08:56 PM	#51 (permalink)
Jordan12berg Base Member Join Date: Jul 2016 Location: Atlanta GA Posts: 70 Drives: 09 370z Red M6 Rep Power: 10	Got it! And 125xxx miles, blown gasket, still no metal shavings at the bottom of the pan or the magnetic plug Rusty likes this.

09-17-2018, 08:24 PM	#53 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 69 Posts: 35,514 Drives: 2011 Nismo GM 6M Rep Power: 2684439	You putting it back together again? How bad was the gaskets? Yeah, sometimes those small bolts don't have enough head on them for a good bite. __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html Last edited by Rusty; 09-17-2018 at 08:27 PM.

09-18-2018, 09:44 PM	#60 (permalink)
Jordan12berg Base Member Join Date: Jul 2016 Location: Atlanta GA Posts: 70 Drives: 09 370z Red M6 Rep Power: 10	So they are definitely more than hand right with loctite, I should be good right? And these are the “upgraded bolts” from concept Z And looking at the DIY pictures it looks like they stripped on them as well. Last edited by Jordan12berg; 09-18-2018 at 09:50 PM. Reason: Additional letters

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Ticking noise above 45mph	owenismo	Engine & Drivetrain	1	11-21-2016 04:42 AM
Rapid clicking/ticking noise while turning all the way	YamahaR6	Nissan 370Z General Discussions	6	06-23-2014 09:06 PM
Ticking noise while shifting	ALTN8NRG	Engine & Drivetrain	4	07-01-2012 05:19 AM
Loud ticking noise from engine	Synack	Nissan 370Z Warranty / Scheduled Maintenance / Servicing / Repairs	191	03-01-2012 06:22 PM
Ticking noise	zrider	Intake/Exhaust	14	07-27-2010 03:57 PM

09-13-2018, 02:47 PM	#46 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 14,125 Drives: 2013 Nismo 370z Rep Power: 2684394	Yeap, Galley gasket has failed.

09-14-2018, 06:51 PM	#47 (permalink)
Jordan12berg Base Member Join Date: Jul 2016 Location: Atlanta GA Posts: 70 Drives: 09 370z Red M6 Rep Power: 10	Any pro tips on this oil pan? I can’t even get a razor blade to the glue

09-14-2018, 08:01 PM	#49 (permalink)
Jordan12berg Base Member Join Date: Jul 2016 Location: Atlanta GA Posts: 70 Drives: 09 370z Red M6 Rep Power: 10	I had all the screws removed originally, I can put a few screws in. The problem is I I have even but a razor blade on a handle and slightly tapped it in and It won’t even let the razor in. It’s so tight at the split line.

09-17-2018, 08:11 PM	#52 (permalink)
Jordan12berg Base Member Join Date: Jul 2016 Location: Atlanta GA Posts: 70 Drives: 09 370z Red M6 Rep Power: 10	Great these bolts for the galley gaskets, the 4mm hex bolts, are starting to strip before I get them to 12ftlbs. I put loctite on them.

09-17-2018, 08:30 PM	#54 (permalink)
Jordan12berg Base Member Join Date: Jul 2016 Location: Atlanta GA Posts: 70 Drives: 09 370z Red M6 Rep Power: 10	Yea finally, they were pretty much exploded on the sideways Y piece. So my torque wrench can’t even torque down to 12 before they strip. It’s close but it won’t click before they give. I got loctite on them am I going to be ok?

09-18-2018, 02:23 PM	#56 (permalink)
Jordan12berg Base Member Join Date: Jul 2016 Location: Atlanta GA Posts: 70 Drives: 09 370z Red M6 Rep Power: 10	Haha torque wrench is in ft lbs. I have a hex tool set with a 3/8 connection set I was using. But yea I followed this DIY: 370z Oil Galley #9 says 12 ft lbs and I dug up all bolt orders and tq specs in the fsm.

09-18-2018, 06:54 PM	#58 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 14,125 Drives: 2013 Nismo 370z Rep Power: 2684394	Doesn't someone make upgraded bolts that can be torqued properly? I am not sure who makes them, that's what is going on my car. Do a search, it is on here somewhere. The bolts and gaskets are upgraded.