I'm trying to figure out the necessity of a part

steveycheesey · 05-18-2016, 04:22 PM

A few weeks ago I installed the AAM 2.5" midpipe into my 09 370z. After the installation was complete I noticed a really loud rattle when ever the rev died down. I found out that when the exhaust was vibrating it would rattle against this "v bar" that is right about the midpipe itself. I've removed this bar multiple times while doing work on the car and am curious if that bar is required or not. Does it do anything of significance for my car or can I just remove it. As of right now removing the bar is the only thing that I can think of that would remedy this loud rattle. Any assistance or advice would be greatly appreciated. Thanks in advance. And if there has been any other threads regarding this topic, I apologize, I probably just didn't know how to word the search.

TerribleONE · 05-18-2016, 04:35 PM

Quote:

Originally Posted by steveycheesey

A few weeks ago I installed the AAM 2.5" midpipe into my 09 370z. After the installation was complete I noticed a really loud rattle when ever the rev died down. I found out that when the exhaust was vibrating it would rattle against this "v bar" that is right about the midpipe itself. I've removed this bar multiple times while doing work on the car and am curious if that bar is required or not. Does it do anything of significance for my car or can I just remove it. As of right now removing the bar is the only thing that I can think of that would remedy this loud rattle. Any assistance or advice would be greatly appreciated. Thanks in advance. And if there has been any other threads regarding this topic, I apologize, I probably just didn't know how to word the search.

Assuming you are talking about the cross brace? I wouldn't remove it. Have you contacted AAM? Sounds like your mid pipe doesn't fit right to me.

Zbrah · 05-18-2016, 04:51 PM

Same issues with Ark exhaust as well but it's an easy fix. You need to loosen the bolts on both ends of the mid pipe. Push the pipe up to create enough spacing between it and the cross member then have someone hold the pipe in that position while you tighten the bolts. This is assuming you're doing it with the car on a lift.

barncobob · 05-19-2016, 06:36 AM

Dirk McGurck · 05-19-2016, 09:21 AM

Make sure your hangers are bent/stretched?

VQZ34 · 05-20-2016, 12:24 PM

Just loose all of the bolts push the mid pipe with a jack and then adjust everything, same thing happen with my ark exhaust and did that and nothing since then, it'll give like a finger of clearance but will work

Sent from my SM-G930T using Tapatalk

05-18-2016, 04:22 PM	#1 (permalink)
steveycheesey Base Member Join Date: Oct 2015 Location: Maryland Age: 31 Posts: 1 Drives: 09 Nissan 370z CS M6 Rep Power: 9	I'm trying to figure out the necessity of a part A few weeks ago I installed the AAM 2.5" midpipe into my 09 370z. After the installation was complete I noticed a really loud rattle when ever the rev died down. I found out that when the exhaust was vibrating it would rattle against this "v bar" that is right about the midpipe itself. I've removed this bar multiple times while doing work on the car and am curious if that bar is required or not. Does it do anything of significance for my car or can I just remove it. As of right now removing the bar is the only thing that I can think of that would remedy this loud rattle. Any assistance or advice would be greatly appreciated. Thanks in advance. And if there has been any other threads regarding this topic, I apologize, I probably just didn't know how to word the search.

05-18-2016, 04:51 PM	#3 (permalink)
Zbrah A True Z Fanatic Join Date: May 2013 Location: The370Z.com Posts: 4,956 Drives: 370Z Rep Power: 5451	Same issues with Ark exhaust as well but it's an easy fix. You need to loosen the bolts on both ends of the mid pipe. Push the pipe up to create enough spacing between it and the cross member then have someone hold the pipe in that position while you tighten the bolts. This is assuming you're doing it with the car on a lift. axmea? likes this. __________________

05-19-2016, 09:21 AM	#5 (permalink)
Dirk McGurck Track Member Join Date: Jun 2014 Location: Delaware Posts: 715 Drives: 09 MB 370Z Touring Rep Power: 20	Make sure your hangers are bent/stretched? __________________ 2009 370Z Touring with Sport

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
I cannot figure this out	smoothtransit	Engine & Drivetrain	20	07-03-2015 05:09 PM
necessity of gaskets	Hitmeplease	Exterior & Interior	2	10-14-2014 08:22 PM
Is Voltage Stabilizer a necessity or waste of money?	andreschen	Nissan 370Z Owners Manual / Service Manuals	9	07-14-2012 05:42 AM
Please help noob figure out if this will fit	alexanderb	Wheels & Tires	4	01-01-2010 12:03 PM
The role and necessity of dual action polishers	spearfish25	Exterior & Interior	10	11-27-2009 12:17 PM

05-19-2016, 06:36 AM	#4 (permalink)
barncobob A True Z Fanatic Join Date: Sep 2015 Location: hangtown, CA Posts: 1,164 Drives: 16 370Z auto Rep Power: 589

05-20-2016, 12:24 PM	#6 (permalink)
VQZ34 Base Member Join Date: Dec 2014 Location: Stockton Posts: 197 Drives: 97 acura CL Rep Power: 10	Just loose all of the bolts push the mid pipe with a jack and then adjust everything, same thing happen with my ark exhaust and did that and nothing since then, it'll give like a finger of clearance but will work Sent from my SM-G930T using Tapatalk