Jim Wolf Cam testing for the VQ37VHR -- Results inside!

SG4247 · 06-07-2019, 08:59 AM

Be really interested in which valve spring compressor tool you plan to use, and how well it ends up working.

johnnydrama · 06-07-2019, 11:04 AM

Quote:

Originally Posted by SG4247

Be really interested in which valve spring compressor tool you plan to use, and how well it ends up working.

Jon at Z1 recommended a Universal Overhead Valve Spring Compressor. Fortunately we have one so that’s what we are going to try first.

1slow370 · 06-07-2019, 06:48 PM

just dont F up your' lifter bores

1slow370 · 06-07-2019, 06:53 PM

Also not saying its going to happen but if you dont remove the upper pan when you go to put the oil pump back on you stand a good chance of cutting the oring while putting it back in also the front cover is a bitch to rtv and reinstall with the upper pan in place silicone everywhere it shouldnt be and not enough where it should be. This leads to oil leaks at the front of the pan.

johnnydrama · 06-08-2019, 01:24 PM

The universal spring compressor wouldn’t work. We engineered our own tool using the items in the picture below.

SG4247 · 06-08-2019, 02:40 PM

Clearly Jon doesnt know what f*** he is talking about.

johnnydrama · 06-08-2019, 04:49 PM

Quote:

Originally Posted by SG4247

Clearly Jon doesnt know what f*** he is talking about.

Jon Parnham, one of the better known and respected tuners on our cars so I doubt it. I’d say it’s more likely that they have a different tool.

SG4247 · 06-08-2019, 05:27 PM

Tuner - engine builder - retailer are not the same things - lol

I would have expected guidance from the vendor on the best tool for this job.

Looks like you made something work, share another pic?

Hotrodz · 06-08-2019, 06:10 PM

Quote:

Originally Posted by SG4247

Tuner - engine builder - retailer are not the same things - lol

I would have expected guidance from the vendor on the best tool for this job.

Looks like you made something work, share another pic?

LMAO, you must not know much about Z1. Jon is all three and one of the best with a vq!

Sent from my SM-G965U using Tapatalk

SG4247 · 06-08-2019, 06:24 PM

Lol ok !

I know they lie, on several occasions.

And this post on valve spring compressors!

Here is the tool that appears to be recommended by the cam designer/engine builder.

http://www.jimwolftechnology.com/cus...asp?PartID=485

Hotrodz · 06-08-2019, 06:49 PM

Quote:

Originally Posted by SG4247

Lol ok !

I know they lie, on several occasions.

And this post on valve spring compressors!

Here is the tool that appears to be recommended by the cam designer/engine builder.

http://www.jimwolftechnology.com/cus...asp?PartID=485

I hear what you are saying but sometimes a someone can use a tool in away others may not be able to duplicate. I doesn't make them wrong!

Sent from my SM-G965U using Tapatalk

johnnydrama · 06-08-2019, 07:33 PM

Quote:

Originally Posted by Hotrodz

I hear what you are saying but sometimes a someone can use a tool in away others may not be able to duplicate. I doesn't make them wrong!

Sent from my SM-G965U using Tapatalk

Personally I’ve got nothing but love for Z1 and don’t feel let down or misled in anyway. I’ve spent thousands upon thousands with them for a reason and they are my go to source. There are literally hundreds universal spring compressors. At first he mentioned the JWT option, then put me on hold to ask one of the techs just to make sure and he said they were having better luck with a universal.

Regardless we came up with something that works easily and that’s all I really care about.

Forum sure has change since 09-10 when I owned my first Nismo, everyone on this forum was in it together, haters were the minority. A lot of the guys on here today should be driving V6 Mustangs and don’t deserve such a great car. Just don’t understand the negativity.

johnnydrama · 06-08-2019, 07:33 PM

Quote:

Originally Posted by Hotrodz

LMAO, you must not know much about Z1. Jon is all three and one of the best with a vq!

Sent from my SM-G965U using Tapatalk

Thank you!

Hotrodz · 06-08-2019, 08:24 PM

Quote:

Originally Posted by johnnydrama

Personally I’ve got nothing but love for Z1 and don’t feel let down or misled in anyway. I’ve spent thousands upon thousands with them for a reason and they are my go to source. There are literally hundreds universal spring compressors. At first he mentioned the JWT option, then put me on hold to ask one of the techs just to make sure and he said they were having better luck with a universal.

Regardless we came up with something that works easily and that’s all I really care about.

Forum sure has change since 09-10 when I owned my first Nismo, everyone on this forum was in it together, haters were the minority. A lot of the guys on here today should be driving V6 Mustangs and don’t deserve such a great car. Just don’t understand the negativity.

Hey, I remember when I joined and back in 2012. I was so inspired by your car as were many others. I learned a lot from all the OGs and others. I was sad when you sold your car but understood since I'm a little older lol. Now I know enough to call BS when I see it and there are still a decent cohort of us old members to keep things on the up and up around here. Many are miss guided or had a bad experience or know someone that did with a reputable business, tuner or mechanic and therefore they want to slam them. Well I have met a few of the best a ZDAYZ over the years and I have gained great respect for what they bring to the community even if they aren't perfect. Stay the course as you are inspiring lots of enthusiast here. I look forward to your build and love the fact that you doing the build with your dad!

Sent from my SM-G965U using Tapatalk

Spooler · 06-08-2019, 11:52 PM

Haters are gonna hate. I have made tools before also and I keep them around to use again. I understand why your father took the back of the front cover off. Unless you have a lift, it's not easy getting the 2nd oil pan off. Someone with a lift could of had the tranny out in 45min and the oil pan off in the same time. That front cover is no joke, but if you are on jackstands, I would have done the same. MA drops the whole motor and cradle out of the car to change the cams. Different strokes for different folks.

06-07-2019, 06:48 PM	#558 (permalink)
1slow370 A True Z Fanatic Join Date: Aug 2009 Location: In the D Posts: 3,732 Drives: v8 74 260z ;) Rep Power: 7250	just dont F up your' lifter bores __________________ ANSWER PRICE LIST Answers - - - - - - - - - - - - - - - - $0.75 Answers (requiring thought) - - - - $1.25 Answers (correct) - - - - - - - - - - $12.50

06-07-2019, 06:53 PM	#559 (permalink)
1slow370 A True Z Fanatic Join Date: Aug 2009 Location: In the D Posts: 3,732 Drives: v8 74 260z ;) Rep Power: 7250	Also not saying its going to happen but if you dont remove the upper pan when you go to put the oil pump back on you stand a good chance of cutting the oring while putting it back in also the front cover is a bitch to rtv and reinstall with the upper pan in place silicone everywhere it shouldnt be and not enough where it should be. This leads to oil leaks at the front of the pan. __________________ ANSWER PRICE LIST Answers - - - - - - - - - - - - - - - - $0.75 Answers (requiring thought) - - - - $1.25 Answers (correct) - - - - - - - - - - $12.50

06-08-2019, 05:27 PM	#563 (permalink)
SG4247 Track Member Join Date: Oct 2016 Location: OKC Posts: 723 Drives: 2010 touring Rep Power: 4486	Tuner - engine builder - retailer are not the same things - lol I would have expected guidance from the vendor on the best tool for this job. Looks like you made something work, share another pic? Last edited by SG4247; 06-08-2019 at 05:39 PM.

06-08-2019, 06:24 PM	#565 (permalink)
SG4247 Track Member Join Date: Oct 2016 Location: OKC Posts: 723 Drives: 2010 touring Rep Power: 4486	Lol ok ! I know they lie, on several occasions. And this post on valve spring compressors! Here is the tool that appears to be recommended by the cam designer/engine builder. http://www.jimwolftechnology.com/cus...asp?PartID=485 Last edited by SG4247; 06-08-2019 at 06:36 PM.

06-08-2019, 11:52 PM	#570 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,504 Drives: 2013 Nismo 370z Rep Power: 2684391	Haters are gonna hate. I have made tools before also and I keep them around to use again. I understand why your father took the back of the front cover off. Unless you have a lift, it's not easy getting the 2nd oil pan off. Someone with a lift could of had the tranny out in 45min and the oil pan off in the same time. That front cover is no joke, but if you are on jackstands, I would have done the same. MA drops the whole motor and cradle out of the car to change the cams. Different strokes for different folks. Hotrodz and jchammond like this.

06-07-2019, 08:59 AM	#556 (permalink)
SG4247 Track Member Join Date: Oct 2016 Location: OKC Posts: 723 Drives: 2010 touring Rep Power: 4486	Be really interested in which valve spring compressor tool you plan to use, and how well it ends up working.

06-08-2019, 02:40 PM	#561 (permalink)
SG4247 Track Member Join Date: Oct 2016 Location: OKC Posts: 723 Drives: 2010 touring Rep Power: 4486	Clearly Jon doesnt know what f*** he is talking about.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
OEM Denso VQ37VHR Fuel injector Flow Test results	MILENKOGT	Engine & Drivetrain	13	08-30-2015 04:52 PM
GTM Stage 2 Supercharger Preliminary Testing Results	SAM@GTM	Forced Induction	576	01-15-2014 09:40 PM
Uprev Tuned at Z1, results inside :)	'10Anamoly	Tuning	12	01-01-2012 12:32 PM
1/4 mile results inside	ZforMe	Track / Autocross / Drifting / Dragstrip	32	04-24-2009 07:27 AM
Knock on the VQ37VHR - gear heads step inside	BerkTech	Intake/Exhaust	39	04-13-2009 10:37 AM