AMS Adjustable Short Throw Shifter available @ Z1 Motorsports

NewYorkJon34 · 06-07-2010, 12:02 PM

Oh and which AMS is this then, do they have a website?

NewYorkJon34 · 06-12-2010, 08:07 AM

Do u cut the little zip tie that is tied to the bottom ring?

Dustin@Z1 · 06-14-2010, 09:17 AM

The AMS that produces this shifter is Absolute Motor Specialties from Canada. Not the AMS renowned for the Time Attack EVO's and GT-Rs. They are two separate companies.

As for the question about the zip at the bottom, yes. That Zip tie is only on there for the purpose of shipping. The plastic washers and metal inner sleeve would simply fall out and float around in the packaging during shipping. Simply cut it off at the time of installation.

NewYorkJon34 · 07-02-2010, 03:36 PM

I just had this installed as well, it does vibrate alil bit, but I've noticed lately sometimes if I "gun it" in second I will hear an almost rattle type noise and when I went to the gas station the other day it was rattling my shift knob alil. I noticed the rubber boot kept coming up and I had to push it back down. It kinda feels like the stock shifter actually, or maybe I've gotten used to it. Also how do you raise/lower the ams shifter kit?

snapping · 07-03-2010, 03:30 AM

yea i feel like mines not smooth when moving it side to side in neutral it even gets stuck on the right sometimes =/ i figure it just needs to be broken in a little though just got it installed 2 days ago so time will tell

NewYorkJon34 · 07-03-2010, 08:10 AM

Ya side to side is not as smooth as stock, and it kinda likes to get stuck while taking it outta reverse.

Dustin@Z1 · 07-03-2010, 04:28 PM

Snapping & Jon I will be sending you a replacement piece for your AMS Shifters. We to have started experiencing a slight rattle on with the shifter. The culprit is the two metal washers on top. We have a remedy. I will drop them in the mail for you guys on Tuesday. The install of this piece just requires removal of the shift knob, nothing major.

Dustin

NewYorkJon34 · 07-03-2010, 05:31 PM

cool, thanks dustin for continued great customer service. What is the piece?, and how do I install it?

NewYorkJon34 · 07-03-2010, 05:35 PM

Also can you PM just to confirm the address?

Dustin@Z1 · 07-05-2010, 09:14 AM

The replacement piece is a plastic spacer made from Polycarbonate. It will not rattle like the metal washers do and raises the shift boot spacer the correct amount to meet the shift knob.

Jon, PM sent.

Dustin

Dan Z Man · 11-08-2010, 01:37 PM

just ordered my short shifter from you guys(and my rear fog light

) i'm very excited and cant wait! i'll try to remember to post my feedback on this!

NewYorkJon34 · 11-08-2010, 01:39 PM

Edit: switched to TWM SS

Dan Z Man · 11-08-2010, 02:24 PM

hmm? how come you switched?

Dustin@Z1 · 11-09-2010, 08:26 AM

Jon experienced an unusual failure with his AMS Short Shifter. This is not very common [something I had not seen] and was covered 100% under AMS's warranty.

John sent his shifter back into us, which we refunded and forwarded onto AMS.

John, what are you thoughts on the TWM piece? It seems that you have to disassemble your factory shifter to properly install that piece.

Z1804 · 11-09-2010, 09:52 AM

I had my AMS short shifter installed at Z1 a few months ago and it works great. I've had no problems with it. I only wish that AMS made it a little shorter. The adjustabilty is a great feature though. Can always adjust it to your preference and comfort.

Thanks to Dustin and Z1!

07-03-2010, 03:30 AM	#50 (permalink)
snapping Base Member Join Date: Jul 2009 Location: Miami Posts: 90 Drives: 09 370z pw 6spd Rep Power: 16	yea i feel like mines not smooth when moving it side to side in neutral it even gets stuck on the right sometimes =/ i figure it just needs to be broken in a little though just got it installed 2 days ago so time will tell __________________ Pw 2009 370z 6mt base with sports /stillen g3/FI CBE 18" CF/Nismo rear bumper/KW V3/SPC front and rear camber kit/AMS shortshifter

11-09-2010, 09:52 AM	#60 (permalink)
Z1804 Premium Member Join Date: May 2010 Location: GA Posts: 784 Drives: 2009 370Z Sport M6 Rep Power: 17	I had my AMS short shifter installed at Z1 a few months ago and it works great. I've had no problems with it. I only wish that AMS made it a little shorter. The adjustabilty is a great feature though. Can always adjust it to your preference and comfort. Thanks to Dustin and Z1! __________________ Z1804 ------ Z1804 ------ Z1804 ------ ------ Z1804 ------ Z1804 ------ Z1804 Fairlady Z 2011 Calendar Now on Sale!!!

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Short throw shifter rattle	Anthny2040	Engine & Drivetrain	16	05-27-2011 10:07 AM
short throw shifter?	tvfreakazoid	Nissan 370Z General Discussions	6	03-09-2009 04:02 AM
Short throw shifter	KameezGuru	Engine & Drivetrain	8	01-24-2009 08:35 AM

06-07-2010, 12:02 PM	#46 (permalink)
NewYorkJon34 A True Z Fanatic Join Date: Jun 2009 Location: Naples, Florida Posts: 3,041 Drives: 09 Fairlady Z Rep Power: 1065	Oh and which AMS is this then, do they have a website?

06-12-2010, 08:07 AM	#47 (permalink)
NewYorkJon34 A True Z Fanatic Join Date: Jun 2009 Location: Naples, Florida Posts: 3,041 Drives: 09 Fairlady Z Rep Power: 1065	Do u cut the little zip tie that is tied to the bottom ring?

06-14-2010, 09:17 AM	#48 (permalink)
Dustin@Z1 The370Z.com Sponsor Join Date: Jun 2009 Location: NLA Posts: 1,313 Drives: NLA Rep Power: 18	The AMS that produces this shifter is Absolute Motor Specialties from Canada. Not the AMS renowned for the Time Attack EVO's and GT-Rs. They are two separate companies. As for the question about the zip at the bottom, yes. That Zip tie is only on there for the purpose of shipping. The plastic washers and metal inner sleeve would simply fall out and float around in the packaging during shipping. Simply cut it off at the time of installation.

07-02-2010, 03:36 PM	#49 (permalink)
NewYorkJon34 A True Z Fanatic Join Date: Jun 2009 Location: Naples, Florida Posts: 3,041 Drives: 09 Fairlady Z Rep Power: 1065	I just had this installed as well, it does vibrate alil bit, but I've noticed lately sometimes if I "gun it" in second I will hear an almost rattle type noise and when I went to the gas station the other day it was rattling my shift knob alil. I noticed the rubber boot kept coming up and I had to push it back down. It kinda feels like the stock shifter actually, or maybe I've gotten used to it. Also how do you raise/lower the ams shifter kit?

07-03-2010, 08:10 AM	#51 (permalink)
NewYorkJon34 A True Z Fanatic Join Date: Jun 2009 Location: Naples, Florida Posts: 3,041 Drives: 09 Fairlady Z Rep Power: 1065	Ya side to side is not as smooth as stock, and it kinda likes to get stuck while taking it outta reverse.

07-03-2010, 04:28 PM	#52 (permalink)
Dustin@Z1 The370Z.com Sponsor Join Date: Jun 2009 Location: NLA Posts: 1,313 Drives: NLA Rep Power: 18	Snapping & Jon I will be sending you a replacement piece for your AMS Shifters. We to have started experiencing a slight rattle on with the shifter. The culprit is the two metal washers on top. We have a remedy. I will drop them in the mail for you guys on Tuesday. The install of this piece just requires removal of the shift knob, nothing major. Dustin

07-03-2010, 05:31 PM	#53 (permalink)
NewYorkJon34 A True Z Fanatic Join Date: Jun 2009 Location: Naples, Florida Posts: 3,041 Drives: 09 Fairlady Z Rep Power: 1065	cool, thanks dustin for continued great customer service. What is the piece?, and how do I install it?

07-03-2010, 05:35 PM	#54 (permalink)
NewYorkJon34 A True Z Fanatic Join Date: Jun 2009 Location: Naples, Florida Posts: 3,041 Drives: 09 Fairlady Z Rep Power: 1065	Also can you PM just to confirm the address?

07-05-2010, 09:14 AM	#55 (permalink)
Dustin@Z1 The370Z.com Sponsor Join Date: Jun 2009 Location: NLA Posts: 1,313 Drives: NLA Rep Power: 18	The replacement piece is a plastic spacer made from Polycarbonate. It will not rattle like the metal washers do and raises the shift boot spacer the correct amount to meet the shift knob. Jon, PM sent. Dustin

11-08-2010, 01:37 PM	#56 (permalink)
Dan Z Man Enthusiast Member Join Date: Dec 2009 Location: North Carolina Posts: 286 Drives: 2010 PG 370z Rep Power: 16	just ordered my short shifter from you guys(and my rear fog light ) i'm very excited and cant wait! i'll try to remember to post my feedback on this!

11-08-2010, 01:39 PM	#57 (permalink)
NewYorkJon34 A True Z Fanatic Join Date: Jun 2009 Location: Naples, Florida Posts: 3,041 Drives: 09 Fairlady Z Rep Power: 1065	Edit: switched to TWM SS

11-08-2010, 02:24 PM	#58 (permalink)
Dan Z Man Enthusiast Member Join Date: Dec 2009 Location: North Carolina Posts: 286 Drives: 2010 PG 370z Rep Power: 16	hmm? how come you switched?

11-09-2010, 08:26 AM	#59 (permalink)
Dustin@Z1 The370Z.com Sponsor Join Date: Jun 2009 Location: NLA Posts: 1,313 Drives: NLA Rep Power: 18	Jon experienced an unusual failure with his AMS Short Shifter. This is not very common [something I had not seen] and was covered 100% under AMS's warranty. John sent his shifter back into us, which we refunded and forwarded onto AMS. John, what are you thoughts on the TWM piece? It seems that you have to disassemble your factory shifter to properly install that piece.