DIY: Finally Installed The STILLEN G3 Intake today! Lots of Pics inside (AK370Z)

pfdaxe · 02-02-2013, 12:49 PM

The G37 and 370Z intakes are not interchangable

Quote:

Originally Posted by Gibby1113

I was noticing on the stillen website that the GIII's that are made for the G37 come with some sort of splash gaurds for the filters. I was wondering if the GII's for our Z's have it as well? Only reason I am asking is because the stillen website does not mention it coming with the intakes, I haven't seen anyone installing them on their Z's, and I thought the parts for the G37 and 370Z were interchangeable for the most part. I really want these but idk if I should due to the fact that water can get them. The gains are ridiculous and it just looks awesome when you open up the hood IMO. Any help is appreciated, thanks!

roy'sz · 02-02-2013, 08:32 PM

I I stalled mi e today using a burr bit on my diegrinder....made cutting a whole lot faster. Both holes modified in approx. 3min. All in all 2hrs for install. Forgot to put my stirafoam bumper on.

Kabestro · 02-03-2013, 06:08 PM

Another fast way to cut the holes is use a drill. Drill a couple of holes horizontal and go straight up with the drill bit. That's what I did since I don't have a cutter.

DEpointfive0 · 02-03-2013, 06:11 PM

Quote:

Originally Posted by Kabestro

Another fast way to cut the holes is use a drill. Drill a couple of holes horizontal and go straight up with the drill bit. That's what I did since I don't have a cutter.

That's what I did too, the dremel saving was taking WAYYYYYY too long

roy'sz · 02-03-2013, 06:12 PM

Thats why I have a $14 diegrinder and air compressor with burr bits. Easier than grading cheese!

roy'sz · 02-04-2013, 12:25 AM

Also thought I might add, it would be useful to pur your wipers at top center and shut the carr off so you can get plastic panel off to gain access to rear mounting bolts on strut brace. Just a fyi incase it wasn't covered in this write up.

7speed · 02-08-2013, 03:07 PM

Thanks. I used some of this to help me install my AEM intake.

Now where was that posting of resetting the door open auto windows up down.......

Trips · 02-08-2013, 04:04 PM

Quote:

Originally Posted by 7speed

Thanks. I used some of this to help me install my AEM intake.

Now where was that posting of resetting the door open auto windows up down.......

1. Push the ignition switch to the ON position.

2. Close the door.

3. Open the window completely by operating
the power window switch.

4. Pull the power window switch and hold it to
close the window, and then hold the switch
more than 3 seconds after the window is
closed completely.

5. Release the power window switch. Operate
the window by the automatic function to
confirm the initialization is complete.

6. Perform steps 2 through 5 above for other
windows.

Kabestro · 02-09-2013, 12:09 PM

So, took the car to the Dyno with the Stillen G3, 295 Hp. not bad. That's gonna be my baseline. Amazing intake...

7speed · 02-10-2013, 01:40 PM

Quote:

Originally Posted by Triple's

1. Push the ignition switch to the ON position.

2. Close the door.

3. Open the window completely by operating
the power window switch.

4. Pull the power window switch and hold it to
close the window, and then hold the switch
more than 3 seconds after the window is
closed completely.

5. Release the power window switch. Operate
the window by the automatic function to
confirm the initialization is complete.

6. Perform steps 2 through 5 above for other
windows.

Thanks, I did a little searching and found it right before you post. Everything is all good now.

Good job Kabestro. I'll have to do the same with my AEM intake. I wanted to get baseline but car was out of commission when I had the chance.

BlueMug · 02-16-2013, 11:20 AM

Quote:

Originally Posted by BlueMug

I noticed one post mentioned the CEL light came on. Shortly after my install I had the service engine soon light on... throwing code P0300... reset the and checked the MAFs and clamps... all good. The SES light came right back on. Anyone else have this issue?

Just a follow up to my previous post... I tightened the hell out of all the clamps and swamped the MAF sensors. Then I placed the negative back on the battery and completed an ECU reset. After the reset, I started the car and let it idle for 15 minutes... haven't had an indicator light on since, over 300 miles now - seems like it worked!

SAmilitaryman · 02-20-2013, 03:45 PM

Used this guide to install my G3 today. Thanks for posting it!

BeemaaZ · 02-26-2013, 03:51 AM

AK, Thank you for pointing out the A/C lines rubbing the Intakes. This will safe $$$ cost of repairs. Good looking out!

bigpat728 · 03-24-2013, 06:33 PM

thank you for the wright up. it helped out a lot

RJ89 · 04-16-2013, 01:54 AM

Thank you so much for this guide! I don't think I would've been able to do this in the time that I did... those stillen instructions were confusing!

02-02-2013, 08:32 PM	#182 (permalink)
roy'sz A True Z Fanatic Join Date: Aug 2011 Location: palmdale, ca Posts: 1,299 Drives: 2010 nissan 370z Rep Power: 16	I I stalled mi e today using a burr bit on my diegrinder....made cutting a whole lot faster. Both holes modified in approx. 3min. All in all 2hrs for install. Forgot to put my stirafoam bumper on. __________________ https://www.youtube.com/watch?v=RtvG...data_playerARK HFC'S-ARK Grip-Stillen G3-M370-UPREV-Kinetix upper control arm-WC Latheworks-Stage2 Bad@$$ Driver(318whp/268tq)- Last edited by roy'sz; 02-02-2013 at 08:35 PM.

02-03-2013, 06:12 PM	#185 (permalink)
roy'sz A True Z Fanatic Join Date: Aug 2011 Location: palmdale, ca Posts: 1,299 Drives: 2010 nissan 370z Rep Power: 16	Thats why I have a $14 diegrinder and air compressor with burr bits. Easier than grading cheese! __________________ https://www.youtube.com/watch?v=RtvG...data_playerARK HFC'S-ARK Grip-Stillen G3-M370-UPREV-Kinetix upper control arm-WC Latheworks-Stage2 Bad@$$ Driver(318whp/268tq)-

02-04-2013, 12:25 AM	#186 (permalink)
roy'sz A True Z Fanatic Join Date: Aug 2011 Location: palmdale, ca Posts: 1,299 Drives: 2010 nissan 370z Rep Power: 16	Also thought I might add, it would be useful to pur your wipers at top center and shut the carr off so you can get plastic panel off to gain access to rear mounting bolts on strut brace. Just a fyi incase it wasn't covered in this write up. __________________ https://www.youtube.com/watch?v=RtvG...data_playerARK HFC'S-ARK Grip-Stillen G3-M370-UPREV-Kinetix upper control arm-WC Latheworks-Stage2 Bad@$$ Driver(318whp/268tq)-

02-08-2013, 03:07 PM	#187 (permalink)
7speed Track Member Join Date: Jan 2013 Location: Dallas Posts: 697 Drives: 09 370 sports clone Rep Power: 14	Thanks. I used some of this to help me install my AEM intake. Now where was that posting of resetting the door open auto windows up down....... __________________ 09 370z 6spd traded 1/12/15 for 15 Challenger RT 6spd Last edited by 7speed; 02-08-2013 at 03:09 PM.

02-26-2013, 03:51 AM	#193 (permalink)
BeemaaZ A True Z Fanatic Join Date: Sep 2011 Location: Irvine, CA Posts: 2,594 Drives: 40thAE#472 Rep Power: 508	AK, Thank you for pointing out the A/C lines rubbing the Intakes. This will safe $$$ cost of repairs. Good looking out! AK370Z likes this. __________________ SoCal 40th Meet Old & New Mods Steering Lock RECALL**** Own 40th 370Z? Get the build # and the Manuf. date here

02-03-2013, 06:08 PM	#183 (permalink)
Kabestro Enthusiast Member Join Date: Aug 2012 Location: Puerto Rico Posts: 331 Drives: 13 Nissan 370Z MR M6 Rep Power: 40	Another fast way to cut the holes is use a drill. Drill a couple of holes horizontal and go straight up with the drill bit. That's what I did since I don't have a cutter.

02-09-2013, 12:09 PM	#189 (permalink)
Kabestro Enthusiast Member Join Date: Aug 2012 Location: Puerto Rico Posts: 331 Drives: 13 Nissan 370Z MR M6 Rep Power: 40	So, took the car to the Dyno with the Stillen G3, 295 Hp. not bad. That's gonna be my baseline. Amazing intake...

02-20-2013, 03:45 PM	#192 (permalink)
SAmilitaryman Base Member Join Date: Jan 2013 Location: san antonio, tx Posts: 168 Drives: 09 Nissan black 370z Rep Power: 13	Used this guide to install my G3 today. Thanks for posting it!

03-24-2013, 06:33 PM	#194 (permalink)
bigpat728 Base Member Join Date: Dec 2012 Location: houston Posts: 48 Drives: 09 nissan 370z Rep Power: 13	thank you for the wright up. it helped out a lot AK370Z likes this.

04-16-2013, 01:54 AM	#195 (permalink)
RJ89 Base Member Join Date: Dec 2012 Location: Vegas Posts: 26 Drives: '13 Touring/Sport Z Rep Power: 13	Thank you so much for this guide! I don't think I would've been able to do this in the time that I did... those stillen instructions were confusing! AK370Z likes this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Fujimura cf Rear diffuser installed! (with pics)( AK370Z)	AK370Z	Exterior & Interior	73	04-24-2016 04:47 PM
Finally Got my exhaust! HKS Hi-Power Ti Exhaust (many Pics, Video inside AK370Z)	AK370Z	Intake/Exhaust	102	05-11-2013 01:32 PM
Finally Fully Detailed My 370Z with Porter Cable (AK370Z) 90+ pics inside	AK370Z	Detailing / Washing / Waxing / Cosmetic Maintenance and Repair	24	06-11-2011 08:48 PM
finally amuse stti extra exhaust arrived + lots of pics	zuperman 370	Intake/Exhaust	22	03-16-2011 12:25 AM
Installed my Stillen G3s. lots of pics and a short review	ssqpolo	Nissan 370Z Photos / Spyshots / Video / Media Gallery	45	09-23-2009 03:20 PM