Lowering Springs Comparisons

shadow85

How was that an argument, I was just stating what eBay wrote. I didn't agree or disagree with it. And link to the information you are referring to?

Chuck33079

Search for it yourself. There are tons of threads here with what you need. This forum needs to stop spoon feeding you information.

__________________
2011 MB Touring-Sport-6sp-Nav/GTM TT/FI TT TDX/JTran/Kosmic/Eibach/Hotchkis/SPC/CSF/RPS/SoThatsWhereAllMyMoneyWent

shadow85

But I am a baby, I need to be spoon fed!

Chuck33079

Pretty much. Your entire post history backs that up. Read more, post less.

__________________
2011 MB Touring-Sport-6sp-Nav/GTM TT/FI TT TDX/JTran/Kosmic/Eibach/Hotchkis/SPC/CSF/RPS/SoThatsWhereAllMyMoneyWent

shadow85

Babies can't spoon feed themselves, they will die.

Chuck33079

We should be so lucky.

__________________
2011 MB Touring-Sport-6sp-Nav/GTM TT/FI TT TDX/JTran/Kosmic/Eibach/Hotchkis/SPC/CSF/RPS/SoThatsWhereAllMyMoneyWent

shadow85

That's horrible!

ChopsZ

Here's a good comparison between stock springs and Ark GT-S springs...

__________________
She's For Sale! PERFORMANCE: Aero Workz | Akebono | BC Racing | EcuTek | HKS | MaxBore | Motordyne | Nismo | RJM | SPL | StopTech | Z1
AUDIO: Arc Audio | Bazooka | Helix | Pioneer | Stereo Integrity

ChopsZ

BTW, that pic above was after rolling right off the rack. I only drove it about 100 feet down the lot and 100 feet back, swerving a little bit both ways to try and "settle" down the ride height. I've been driving on these springs for two weeks now and they haven't settled anymore than what you see above.

Also, a couple quick questions which I have yet to see asked...

1) Has anyone had issues running into the bump stops with lowering springs?
2) Has anyone ever had issues with the drive shaft having less movement between the output shaft of the transmission and input shaft of the differential?

__________________
She's For Sale! PERFORMANCE: Aero Workz | Akebono | BC Racing | EcuTek | HKS | MaxBore | Motordyne | Nismo | RJM | SPL | StopTech | Z1
AUDIO: Arc Audio | Bazooka | Helix | Pioneer | Stereo Integrity

ChopsZ

So does anyone have anything for these questions? Just curious.

__________________
She's For Sale! PERFORMANCE: Aero Workz | Akebono | BC Racing | EcuTek | HKS | MaxBore | Motordyne | Nismo | RJM | SPL | StopTech | Z1
AUDIO: Arc Audio | Bazooka | Helix | Pioneer | Stereo Integrity

ChopsZ

So with ALL of the members on here over ALL of the years of lowering these cars one way or another, no one has any answers for these two questions? Really?...

__________________
She's For Sale! PERFORMANCE: Aero Workz | Akebono | BC Racing | EcuTek | HKS | MaxBore | Motordyne | Nismo | RJM | SPL | StopTech | Z1
AUDIO: Arc Audio | Bazooka | Helix | Pioneer | Stereo Integrity

Rusty

Question 1. Depending on how low you go. Will determine when you will hit the bump stops and how often. Everyone has hit the bump stops at one time or another. You just don't know it.

Question 2. Lowering the car has nothing the do with the driveshaft between the tranny and diff. Both are fixed in position. The driveshaft doesn't move. It's fixed at the diff. You should be concern about the halfshafts between the diff and knuckle. The diff stays in place the the knuckle moves up and down in an arc.

__________________

浪人 - 殺し屋
"The Difficult Anytime, The Impossible By Appointment Only"
http://www.the370z.com/members-370z-...o-journal.html

ChopsZ

Q1) I ask about the bump stops because I wanted to know just how close we actually are to them once lowered. On one of the roads I normally drive on almost daily, there's two manhole covers in the middle of the lane, and for whatever reason, the road has a couple of really sharp dips (ripples) between them. While stock, it's quite an abrupt bounce through there. Now that I'm lowered, it's an actual "jolt" going through there. I'm assuming that jolt is from ramming right into the rear bump stops. It does not seem to bother the front at all.

I'm sure we do all ride the bump stops once in a while without knowing it. If our Z's are setup like Miatas, they are designed to compress the springs fully and then gradually compress the bump stops as the bump stops on Miatas are actually factored into the handling of the car. They rely on riding on the bump stops during hard cornering.


Q2) I don't know why, but for some reason, I have been thinking about it as if it were a live axle, which it's not. I wasn't even thinking about the fact that the diff is physically connected to the chassis. Sorry about that.

On that note, what concerns would there be with the half shafts? Only asking for curiosity reasons. I have no plans on ever going any lower than what the Ark GT-S springs give me.

As it is, I sometimes think I should have stuck to my guns and went with the Swifts. Not because of rubbing or bottoming out, but because the front and rear tires tuck a little now which prevents me from using spacers, and also limits me on eventually going with wider meat front and rear.

__________________
She's For Sale! PERFORMANCE: Aero Workz | Akebono | BC Racing | EcuTek | HKS | MaxBore | Motordyne | Nismo | RJM | SPL | StopTech | Z1
AUDIO: Arc Audio | Bazooka | Helix | Pioneer | Stereo Integrity

Rusty

To get into the halfshafts is long and detailed. It deals with angles of operation, engineering POV. Had to deal with it at work. And I don't feel like getting into right now. But with the Z. You don't have to worry about them. Unless you are pushing mega HP and torque. From a strength POV.

__________________

浪人 - 殺し屋
"The Difficult Anytime, The Impossible By Appointment Only"
http://www.the370z.com/members-370z-...o-journal.html

MaysEffect

Constantly riding on the bumpstops is NOT a good thing. Slamming the bumps can cause damage and premature failure to the damper. Also considering the low profiles tires, this will be exerting more load on the tire sidewall and ultimately the wheel rim. The miata for example had larger sidewalls, softer tires overall and softer bumpstops with more absorption.

There are however aftermarket bumpstops with tuned bump curves that will allow some further compression instead of hard stops in compression stroke.

I'm inclined to believe the jolt you are feeling is from the rear springs binding the "dead springs" Where as the fronts are already fully bound at normal ride height due to the weight bias. Next time you have car up in the air, check if you see scratches/indentations between the tightly bound coils


With regards to the halfshafts, the suspension geometry as factory is designed to keep the shafts relatively level during normal driving conditions. Increased camber, lower ride height. higher torque loads and blown out bushings can cause premature failure to the boots, the internal cages/races and the shaft itself. Ripped boots is a slower wear issue which usually leads to damaged bearings which is a noticeable failure. Damage to the cages and races would almost definitely be catastrophic failure. A snapped shaft is probably the most preferred failure, in a worse case it will bend and start playing hammer fist with the surrounding suspension pieces. This will probably fail at lowspeed.

There are plenty of details on how it all can fail like Rusty suggested.