Small nail in tire, plug or inside patch?

cab83_750 · 12-05-2010, 11:05 PM

Well, I guess with technology, the 'plug' is making a comeback (at least per the article below). I am open to this now (again):

Tire Repair: Patch vs Plug

Q. When I first began driving in the late 1950's, if you got a nail in your tire the only way to fix it was with a "plug" which would be inserted moments after removing the nail. As radials became more prevalent, dismounting the tire and applying a patch on the inside was apparently the preferred method of repair.

Now I notice that the plug repair technique is making a comeback and in many instances is the preferred method. Please comment about the pros and cons of each method as it applies to todays steel belted radials.

A. In the old days plugs were used because they were quick and reliable. If the injury was a simple nail, a tire could be repaired in no time. If the tire was cut, then patching was preferred to completely seal the odd shaped hole. Then when radial tires came out it was found that plugs would warp the tire and make them ride differently. That's when patches became the preferred method of repairing a tire. There were two kinds of patches, cold and hot.

The cold patch required buffing the inside of the tire and applying a cement. Then the correct sized patch was placed over the injury and a special tool was used to "stitch" the patch to the tire. I don't mean stitching in the sense it was sewn on, but that this special tool was rolled over the patch until it was sealed against the tire. The drawback to this method was if you didn't do everything perfectly, the patch would leak.

Hot patching involved essentially the same procedure except the patch was heated and melted to the inside of the tire. There was a special heating clamp that went on the tire to do this. It usually took about 15 minutes to heat the patch to the tire. The advantage of this method was that the tire and patch become one piece.

Now we have plugs that are designed to repair radial tires and are self-vulcanizing. That is to say after they heat up from driving, they "melt" into the tire and become one piece. This is again the preferred method because it is much faster to do. If, as in the old days, a tire was cut then patching is the best way to go.

Patching a tire can take about 30 minutes and installing a plug takes a few minutes and usually can be done while the tire is still on the car. Patching a tire can cost $10.00 to $15.00 and plugging can cost as little as $2.00 but usually $5.00.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Urgent: Replace tire or patch?	dudafunk	Wheels & Tires	23	05-28-2012 02:12 PM
nail in tire	ScGRaceR	Nismo 370Z	3	11-20-2010 07:35 PM
BIG nail in tire!	alexanderb	Wheels & Tires	14	09-20-2010 06:31 PM
Urgent: Replace tire or patch? [Tire Section]	dudafunk	Nissan 370Z General Discussions	0	04-03-2010 12:29 PM
Nice nail in my tire. Had it fixed. Am I good?	shesha	Wheels & Tires	22	03-19-2010 12:45 AM

12-05-2010, 11:05 PM	#23 (permalink)
cab83_750 Track Member Join Date: Apr 2009 Location: CA Posts: 887 Drives: 09 NISSAN 370Z Rep Power: 419	Well, I guess with technology, the 'plug' is making a comeback (at least per the article below). I am open to this now (again): Tire Repair: Patch vs Plug Q. When I first began driving in the late 1950's, if you got a nail in your tire the only way to fix it was with a "plug" which would be inserted moments after removing the nail. As radials became more prevalent, dismounting the tire and applying a patch on the inside was apparently the preferred method of repair. Now I notice that the plug repair technique is making a comeback and in many instances is the preferred method. Please comment about the pros and cons of each method as it applies to todays steel belted radials. A. In the old days plugs were used because they were quick and reliable. If the injury was a simple nail, a tire could be repaired in no time. If the tire was cut, then patching was preferred to completely seal the odd shaped hole. Then when radial tires came out it was found that plugs would warp the tire and make them ride differently. That's when patches became the preferred method of repairing a tire. There were two kinds of patches, cold and hot. The cold patch required buffing the inside of the tire and applying a cement. Then the correct sized patch was placed over the injury and a special tool was used to "stitch" the patch to the tire. I don't mean stitching in the sense it was sewn on, but that this special tool was rolled over the patch until it was sealed against the tire. The drawback to this method was if you didn't do everything perfectly, the patch would leak. Hot patching involved essentially the same procedure except the patch was heated and melted to the inside of the tire. There was a special heating clamp that went on the tire to do this. It usually took about 15 minutes to heat the patch to the tire. The advantage of this method was that the tire and patch become one piece. Now we have plugs that are designed to repair radial tires and are self-vulcanizing. That is to say after they heat up from driving, they "melt" into the tire and become one piece. This is again the preferred method because it is much faster to do. If, as in the old days, a tire was cut then patching is the best way to go. Patching a tire can take about 30 minutes and installing a plug takes a few minutes and usually can be done while the tire is still on the car. Patching a tire can cost $10.00 to $15.00 and plugging can cost as little as $2.00 but usually $5.00.